• Journal of the Korean Society of Visualization
• /
• v.17 no.2
• /
• pp.25-31
• /
• 2019

A device that consists of an array of hydrofoils (called a vane deployer) is widely used in ocean engineering. In general, the vane deployer has to spread out efficiently, which is possible by enhancing the lift-to-drag ratio. In the present study, using a computational fluid dynamics, we investigate the effect of hydrofoil arrangement on the lift-to-drag ratio to establish the condition in which a reasonable level of constant lift-to-drag ratio is achieved in a wide range of angle of attack, to avoid a degradation of the hydrodynamic performance. First, the flow around two-dimensional hydrofoil array is examined by varying the size of hydrofoil components, gap between the hydrofoils, and arrangement type. As a result, we determine the optimized hydrofoil array configuration whose lift-to-drag ratio is nearly independent on the angle of attack. Finally, a three-dimensional simulation is performed for the optimized geometry to estimate the performance of actual vane deployer.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.4
• /
• pp.443-448
• /
• 2015

A swirl type mixer was developed to improve the flow mixing performance of a marine selective catalytic reduction system. In this study, the swirl type mixer and a multi-staged swirl type mixer, in which the angle of the vanes at each stage is controllable were considered to provide the optimal region of angles for the mixers. The effects of the vane angles in both mixers on the uniformity index and pressure drop were investigated using a computational fluid dynamics simulation. In the swirl type mixer, the optimal conditions for the flow mixing performance were observed at vane angles from 30 to 60 degrees when vane angles could be adjusted between 10 to 80 degrees, however, the pressure drop increased continually with increasing vane angle of the mixer. On the other hand, control of the individual staged angles of the multi-staged mixer showed that it is possible to keep enhancing flow mixing performance while reducing the pressure drop.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.5
• /
• pp.44-49
• /
• 2008

As the alternative energy, renewable energy should have been developing by many techniques, in order to substitute the fossil fuel which will be disappeared in the near future. One of the small hydropower generator, main concept of tubular turbine is based on using the different water pressure levels in pipe lines, energy which was initially wasted by using a reducing valve at the end of the pipeline, is collected by turbine in the hydro power generator. A propeller shaped hydro turbine has been used in order to use this renewable pressure energy in order to acquire basic design data of tubular type hydraulic turbine, output power, head, efficiency characteristics due to the guide vane opening angle are examined in detail. First, it ensures the reliance of CFD by that of compared with experiment data. After all, the results of performance characteristics of the CFD and experiment show to confirm the data that power, head and efficiency of less than 4%, 2% and 5% respectively. Moreover influences of pressure, tangential and axial velocity distributions on turbine performance are investigated.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2839-2844
• /
• 2007

Micro hydraulic power generation of which the output is less or equal to a 100kW is attracting considerable attention. This is because of its small, simple, renewable, and abundant energy resources. By using a small hydropower generator of which main concept is based on using the different water pressure levels in pipe lines, energy which was initially wasted by use of a reducing valve at the end of the pipeline, is collected by turbine in the hydropower generator. A propeller shaped hydroturbine has been used in order to use this renewable pressure energy. In this study, in order to acquire basic design data of tubular type hydraulic turbine, output power, head, efficiency characteristics due to the flow coefficient are examined in detail. Moreover influences of pressure and velocity distributions with the variations of runner vane angle on turbine performance are investigated by using a commercial CFD code.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.7
• /
• pp.1044-1050
• /
• 2008

Most of developed countries, the consumption of fossil fuels has been serious problems that cause serious environment pollution like acid rain, global warming. Also, we have faced that limitation fossil fuels will be exhausted. Currently, small hydropower attracts attention because of its small, clean, renewable, and abundant energy resources to develop. By using a small hydropower generator of which main concept is based on using the different water pressure levels in pipe lines, energy which was initially wasted by use of a reducing valve at the end of the pipeline, is collected by turbine in the hydropower generator. A propeller shaped hydroturbine has been used in order to use this renewable pressure energy. In this study, in order to acquire basic design data of tubular type hydraulic turbine, output power, head, efficiency characteristics due to the flow coefficient are examined in detail. Tubular-turbine among small hydraulic power generation can be used at low-head. The purpose of this study is to research turbine's efficiency due to runner vane angle using CFD analysis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.130-134
• /
• 2005

The objectives of this study are to improve the aerodynamics performance on the down-wind blade system with folding type blade which consists of the folding type rotor blade, wind vane yawing stabilizer and a bevel gearbox. The aerodynamics performance for the new wind turbine system are compared with those of the conventional up-wind blade system. In addition to, a novel multi voltage inverter system is applied for reductions of harmonic.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.335-340
• /
• 1992

유압 시스템(System)은 원동기의 기계적 에너지를 유압펌프가 작동유를 압력 에너지의 형태로변환 시켜 이것을 유합 실린더(Cylinder)등의 엑츄에이터(Actuator)가 다시 기계적 에너지로 변환시켜 부하 를 구동하게한다. 상용차(NT-1, KH 등)용 파워스티어링(Power Steering)에 장착되는 Vane Type Oil Pump (이하 VOP)가 바로 이와같은 역할을 담당하고 있다. 본 연구에서는 VOP의 성능과 관련되어지는 주요 제원(Parameter)인 미끄럼부에서의 틈새, 작동유점도, 압력변화, 회전수 등을 다양하게 변화시키는 모의실험(Simulation)을 통하여각각의 조건하에서얻어지는 누설 유량과 체적효율을 수치적 으로 예측하고 이것을 주요제원을 고려하여 해석해서 정량적인 값을 얻는 것을 목적으로한다.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2007.05a
• /
• pp.1992-1996
• /
• 2007

The Kaplan turbine model has been tested and analized. The blade angle and the guide vane opening of the turbine model were designed to be varied according to the best combination of guide vane and runner blade opening. When the changes in head and output were comparatively large, the efficincy drop were small, so the efficiency characteristics and stability of the entire operating condition were maintained in good condition. These results showed that the developed model in this study will be suitable for small hydro power stations with large changes in head and load.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.664-667
• /
• 2009

The Francis type hydro turbine with vertical axis has been designed and analized for hydraulic performance verification. The guide vane angle of turbine casing were designed to be varied according to the condition of head and flowrate. When the changes in flowrate and output were comparatively large, the efficiency drop were small, so the efficiency characteristics and stability of the entire operating condition were maintained in good condition. These results showed that the developed hydro turbine in this study will be suitable for small hydro power stations with medium and high head such as agricultural reservoirs and large dam.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.302-305
• /
• 2009

The Francis type hydro turbine with vertical axis has been designed and analized for hydraulic performance verification. The guide vane angle of turbine casing were designed to be varied according to the condition of head and flowrate. When the changes in flowrate and output were comparatively large, the efficiency drop were small, so the efficiency characteristics and stability of the entire operating condition were maintained in good condition. These results showed that the developed hydro turbine in this study will be suitable for small hydro power stations with medium and high head such as agricultural reservoirs and large dam.