• Tribology and Lubricants
• /
• v.6 no.2
• /
• pp.43-49
• /
• 1990

The Dynamic Behavior in line contacts between the vane tip and camring in an oil hydraulic vane pump with intravanes has been investigated. Variations of the radial acting force of a vane were calculated from previously measured results of dynamic infernal pressure in four chambers surrounding a vane, and variations of the behavior were estimated in both the rotational speed range from 1200 to 2700 rpm and in the delivery pressure range from 10 to 21Mpa. The results indicate the variations of the radial acting force. Under the standard operating condition (to 14 Mpa, 1800 rpm), the radial acting force on the vane is governed by internal dynamic pressures, but it is more influenced by rotating speed at higher than 2000 rpm relatively.

• The KSFM Journal of Fluid Machinery
• /
• v.10 no.4
• /
• pp.9-14
• /
• 2007

The purpose of present work is to analyze the convective heat transfer downstream of mixing vane in subchannel of nuclear reactor with three-dimensional Navier-Stokes equations. SST model is selected as a turbulence closure by comparing the performances of two different turbulent closures. Three different shapes of mixing vane are tested. And, thermal-hydraulic performances of these vanes are discussed. The results show that twist of the vane improves the heat transfer performance far downstream of the vane.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.2
• /
• pp.191-199
• /
• 1992

This paper presents in experimental study of the dynamic internal pressure within an oil hydraulic vane pump. The measurements of the dynamic internal pressures near the vane of a pressure balance type of an oil hydraulic vane pump with intravanes has been made to provide the essential information for the study of the pump dynamics and control, the pump design and the analysis of tribological problems in the sliding components. The influences of the discharge pressure and rotating speed of the vane on the dynamic pressure in four chambers surrounding a vane have been investigated. The results indicate that the surge pressures of the chambers at the instant moment of discharge and closure are affected by the rotating speed. The pressure in the intravane chamber maintains almost constant values, which remarkably effects the pulsating discharge pressure.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.3
• /
• pp.311-318
• /
• 2003

The present work evaluates the effects of mixing vane shape on the flow structure and heat transfer downstream of mixing vane in a subchannel of fuel assembly. by obtaining velocity and pressure fields. turbulent intensity. flow-mixing factors. heat transfer coefficient and friction factor using three-dimensional RANS analysis. Four different shapes of mixing vane. which were designed by the authors were tested to evaluate the performances in enhancing the heat transfer. Standard k-$\varepsilon$ model is used as a turbulence closure model. and. periodic and symmetry conditions are set as boundary conditions. The flow blockage ratio is kept constant. but the twist angle of mixing vane is changed. The results with three turbulence models were compared with experimental data.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1293-1302
• /
• 2001

It is generally known that radial vane blowers with vaneless diffuser may generate mostly only a rotating stall but backward curved vane blowers may do both an impeller and a diffuser rotating stalls. In this study, it was found from the numerical and experimental results that the diffuser rotating stall does not appear in a radial vane because of the suppression for the diffuser stall appearance by occurring of impeller rotating stall in a large flow rate coefficient. The diffuser rotating stalls occurring when the width of diffuser is broaden fur a backward curved vane blower are classified definitely by the diffuser flow rate coefficient defined by adopting the varying diffuser width.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.408-413
• /
• 2003

Naphthalene sublimation technique is used to investigate the average and local heat transfer from the circular rod, and to determine the average and local heat transfer from the circular rod with and without square wing type mixing vane in axial flow. The experiments are performed for a circular rod and flat plate with and without mixing vane in wind tunnel. In comparison with flat plate and circular rod in axial flow, averaged Nusselts number is increased 2 times as the increase of Reynolds number with mixing vane. Longitudinal vortex induced by square wing type has the stronger vortex strength, so square wing type vortex generator shows an effect further in downstream.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.111-117
• /
• 2012

Dust collecting performance of axial-vane type cyclone for oil mist was analyzed in this study. For predicting cut diameter size of cyclone, the number and angle of vane ($tan{{\beta}_2}^{\prime}$) was simulated by CFD. As the result, $tan{{\beta}_2}^{\prime}$ was decreased as the number of vane was increased and the angle of inclination(${{\beta}_2}^{\prime}$) decreased, and it cause strong swirl flow. Therefore, it could be confirmed that as the number of vane was increased and the angle of inclination was decreased, cut diameter size was decreased. Also, by verifying the results of CFD through experiment, the cut diameter size could be $2{\mu}m$ at $4m^3/min$ of flow rate.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.11a
• /
• pp.3-3
• /
• 1997

미사일 수직발사 시스템은 공간을 작게 차지하고 간편하여 각국이 선호하고 있다. 그러나 수직발사 초기에는 매우 낮은 속도로 상승하므로 Fin의 공력이 발생하지 않기 때문에 추력방향을 직접제어하지 않으면 안된다. 추력방향 제어장치는 Gimbal, Jet Vane, Jet Tab, Secondary Injection 등 여러 방식이 있으나 Jet Vane Type의 추력 방향 제어장치는 응답이 빠르고 경량화가 가능하며 후방 Fin과의 연동 및 작동 후 분리가 가능하다는 장점으로 인해 수직발사 미사일의 초기 방향제어에 주로 사용한다. 이 장치는 Vane이 화염 속에서 직접 구동되므로 고내열성 재료의 기술이 필요하며 미사일의 전체 System에 요구되는 Side Force를 발생시키기 위한 Vane의 최대 받음각 및 회전속도를 결정해야 한다. 따라서 초음속 유동해석을 통해서 Vane의 받음각에 대한 Side Force와 Torque를 계산하며, 구조해석을 통해 Side Force가 가해지는 동안의 Housing의 굽힘, 비틀림 하중 등을 계산하였다. 또한 Controller는 기존의 유압방식보다도 소형이며 복잡하지 않고 가격이 싼 DC Motor와 감속기를 이용하여 빠른 응답성에 부합토록 설계하였다. 본론에서는 성능과 관련된 초기 요구조건에 대한 최적설계의 변수들을 해석하고. 그에 따른 개발사양, 개발 과정, 구조, 시험방법 등에 대해 고찰하고자 한다.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.2
• /
• pp.120-130
• /
• 2000

A flow uniformity in a duct cooler of duct system of FGD(Flue Gas Desulfurization) linking a reheater and a absorber has been investigated in the present study. For this purpose, the flow characteristics according to the geometry of a vertical and horizontal vane in a curved duct of the duct system has been examined with the aid of a numerical simulation. The results indicate that the vertical vane with a little deflection toward a recirculation region makes the flow distribution in the duct cooler more uniform than that without deflection, and horizontal vane does not effect the change of the flow distribution for an angle of inclination. The mean flow uniform factor shows its maximum for duct system without the vane(case NP) and its minimum for the vertical vane with a little deflection(case P-0.8-0) .

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.3 s.246
• /
• pp.230-237
• /
• 2006

Flows in the cavity with pump out vane are calculated using the CFX-Tascflow CFD code. flow calculations are performed for different values of vane height, numbers, leakage flow rate, and rotational speed. The flow is very complex and three dimensional with strong vortex and leakage flow over the vane. The variations of pressure coefficient and K-factor with these parameters and resulting effects on the thrust and torque are studied. The present study contributes to showing the capability of flow simulation of back cavity with pump-out vane. The calculated results are good enough to be used back cavity design.