• 설비공학논문집
• /
• 제13권8호
• /
• pp.746-756
• /
• 2001

An experimental study was conducted to investigated the effect of refrigerant flow control on the performance of a variable-speed heat pump operating in both cooling and heating mode. For this purpose, cooling and heating capacity, EER and refrigerant mass flow rate corresponding to an electronic valve as well as a capillary tube were measured as functions of compressor speed, length of capillary tube (or valve opening of the electronic valve), refrigerant charge, and outdoor temperature. From the comparison of experimental results, it was found that the performance variation due to the electronic valve opening became significant as the operating conditions(outdoor temperature and compressor speed) deviated from the standard condition at which heating capacity and EER were rated for the indicated capillary tube.

• 유공압시스템학회논문집
• /
• 제7권4호
• /
• pp.44-49
• /
• 2010

This paper represents solenoid design of control valve for incline angle control in variable compressor. Some theoretical and numerical analysis were performed to analyse solenoid and compared with experimental results. Maxwell program was used for numerical analysis. Through redesigns of housing body, plunger, core, and disk in control valve, the needed force was gotten. Reduction of core groove and housing body air-gap had a large influence on magnetic force. But increasing of disk thickness had little effect on magnetic force. Control valve efficiency could be improved through solenoid redesign.

• 한국분무공학회지
• /
• 제22권1호
• /
• pp.22-28
• /
• 2017

In this study, the effects of intake valve closing timing by using Cam-in-Cam system on combustion and emission characteristics for diesel engine were investigated under GT-POWER simulation environment. As a result, it was found that volumetric efficiency and effective compression ratio were decreased as the intake valve closing(IVC) timing is retarded due to its backflow effect. Also, we found that in-cylinder pressure, heat release rate and NOx emission were decreased as IVC timing was retarded. These show that the LIVC(late intake valve closing) can be effective to control AFR and mixing rate in diffusion combustion of diesel engine.

• 설비공학논문집
• /
• 제22권2호
• /
• pp.97-103
• /
• 2010

For large reciprocating compressors in parallel operation, an analytical study has been carried out on the gas pulsation in associated discharge piping lines. Since the pressure pulsation at a valve, valve dynamics, and the gas flow rate through the valve are interrelated, affecting one another, these need to be solved simultaneously. Acoustic transfer matrix method, which relates acoustic pressure and velocity at one location to those at another location, has been adopted to calculate the effect of the gas flow at one valve location on the gas pulsation at other valve locations.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.995-999
• /
• 2017

제어밸브의 유량계수에 영향을 미치는 인자들을 파악하고 그 영향을 분석하였다. 제어밸브의 유량계수는 레이놀즈 수, 연결 배관의 형상과 표면 조도 등에 영향을 받는다. 따라서 유량계수를 상수로 취급할 수 없다. 그러므로 로켓엔진과 같이 정확한 유량계수를 요구하는 시스템에서 사용할 목적으로 제어밸브의 유량계수를 측정할 때는 실제 사용 환경과 유사한 레이놀즈 수 영역에서, 동일한 조도 및 형상을 가지는 입출구 배관을 사용하여 측정해야 한다.

• Journal of Chest Surgery
• /
• 제23권3호
• /
• pp.514-521
• /
• 1990

Patient with aortic valvular disease have increased left ventricular work and greater myocardial oxygen demand, which may aggravate the effect of concomitant coronary artery disease. Thus in patient who repair aortic valve replacement, concomitant aortocoronary bypass surgery is often performed when angiographically significant coronary artery disease is present. This approach is supported by reports that revascularization does not increase operative risk when associated coronary artery disease is present and significantly reduce the occurrence of late sudden death. Recently we have experienced one case of aortic valve replacement concomitant with aorta-coronary bypass surgery. The patient was 56 year-old male and admitted with complaint of anterior chest pain especially during his exercise. He was diagnosed as aortic valve stenosis and regurgitation [GIII] with proximal right main coronary artery occlusion We performed aortic valve replacement with aorta coronary bypass surgery by use of saphenous vein. Post operative course was uneventful and chest pain was relieved. Post operative coronary angiogram disclosed good patency of grafted vessel.

• International Journal of Fluid Machinery and Systems
• /
• 제5권3호
• /
• pp.109-116
• /
• 2012

Water hammer pumps can effectively use the water hammer phenomenon for water pumping. They are capable of providing an effective fluid transport method in regions without a well-developed social infrastructure. The results of experiments examining the effect of the geometric form of water hammer pumps by considering their major dimensions have been reported. However, these conventional studies have not fully evaluated pump performance in terms of pump head and flow rate, common measures of pump performance. The authors have focused on the effects on the pump performance of various geometric form factors in water hammer pumps. The previous study examined how the hydrodynamic characteristics was affected by the inner diameter ratio of the drive and lift pipes and the angle of the drive pipe, basic form factors of water hammer pumps. The previous papers also showed that the behavior of water hammer pump operation could be divided into four characteristic phases. The behavior of temporal changes in valve chamber and air chamber pressures according to the air volume in the air chamber located downstream of the lift valve was also clarified in connection with changes in water hammer pump performance. In addition, the effects on water hammer pump performance of the length of the spring attached to the drain valve and the drain pipe angle, form factors around the drain valve, were examined experimentally. This study focuses on the form of the lift valve, a major component of water hammer pumps, and examines the effects of the size of the lift valve opening area on water hammer pump performance. It also clarifies the behavior of flow in the valve chamber during water hammer pump operation.

• 드라이브 ㆍ 컨트롤
• /
• 제15권4호
• /
• pp.1-10
• /
• 2018

Spool displacement of a direction control valve is the standard signal to measure the bandwidth frequency of the direction control valve. When the spool displacement signal is not available, it is suggested in this study to use the metering hydraulic line as an alternative way to measure - 90 degree phase bandwidth frequency of the hydraulic direction control valve. Dynamics of the hydraulic line is composed of inertia, capacitance, and friction effects. The effect of oil inertia is dominant in common hydraulic line dynamics and the line dynamics is close to a derivative action in a range of high frequency; such as a range of bandwidth frequency of common directional control valves. Phase difference between spool displacement and line load pressure is nearly constant as a valve close to 90 degree. If phase difference is compensated from the phase between valve input and pressure, compensated phase may be almost same as the phase of spool displacement that is a standard signal to measure phase bandwidth frequency of the directional control valve. A series of experiments were conducted to examine the possibility of using line pressure in to measure phase bandwidth frequency of a directional control valve. Phase bandwidth frequency could be measured with relatively high precision based on metering hydraulic line technique and it reveals consistent results even when valve input, oil temperature, and supply pressure change.

• International Journal of Automotive Technology
• /
• 제2권1호
• /
• pp.1-7
• /
• 2001

This paper presents further investigation into the effect of over-expansion cycle in a spark-ignition engine. On the basis of the results obtained in previous studies, several combinations of late-closing (LC) of intake valve and expansion ratio were tested using a single-cylinder production engine. A large volume of intake capacity was inserted into the intake manifold to simulate multi-cylinder engines. With the large capacity volume, LC can decrease the pumping loss and then increase the mechanical efficiency. Increasing the expansion ratio from 11 to 23.9 with LC application can produce about 13% improvement of thermal efficiency which was suggested to be caused by the increased cycle efficiency. The decrease of compression ratio from 11 to 5.5 gives little effect on the thermal efficiency if the expansion ratio could be kept constant. Thus, the expansion ratio is revealed to be a determining factor for cycle efficiency, while compression ratio is no more important, which suggests the usefulness of controlling the intake charge with intake valve closure timing. These were successfully explained by simple thermodynamic calculation and thus the mechanism could be verified by the estimation.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.66.1-66.1
• /
• 2005