• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.1218-1222
• /
• 2006

The bolts fixing the valve cover to the engine were often reported to be failed in a wheel loader model. Recently this failures were continually repeated in the specified equipment. In order to identify the fatigue fractures of the bolts, various vibration tests were carried out. From these tests, it was found out that the failure was due to the resonance between the excitation force of engine and the transverse mode of engine valve cover. So, the several modifications for the bolts were considered to avoid the resonance. Finally, the bolt failure problem was clearly resolved.

• 설비공학논문집
• /
• 제22권7호
• /
• pp.460-467
• /
• 2010

In housing units constructed recently in Korea, the length of ondol coil is different in each room, so the flow rate of hot water is adjusted by setting valve opening. If the flow rate is not appropriate for heating load, the room temperature seriously deviates from the set temperature range for comfort. In particular, too small valve opening can induce a noise by cavitation. In order to adjust the valve opening, two methods by zone area and a new method by return temperature rise were modelled and simulated using TRNSYS and EES. As a result, heating energy consumption during one week was the same on three methods, but the room temperature of the new method minimally deviated from the range of set temperature with a low possibility of noise.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.661-665
• /
• 2005

The muffler reducing the exhaust noise and vibration from the engine influence on the engine performance. Recently the semi-active muffler was developed and adopted to the actual use in consideration of the cost and technical side for noise and vibration. This study is about the recently developed semi-active muffler. This paper attempt to analyze the dynamic stress field on the gate plate by using the finite element methods. According to the analysis of the Exhaust Variable Valve, its spring has the most influence on its operation compare with effects of other components. The design parameters of the Exhaust Variable Valve such as the spring displacement, diameter, coil number, free angle and so forth were used.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.331-336
• /
• 2012

This paper proposes a new type of high-frequency directional valve controlled by the piezostack actuator associated with displacement amplifier. As a first step, a dynamic model of directional valve which can operate at 200 Hz with a flow rate of 12 l/min is derived by considering pressure drop and flow force. As a second step, an appropriate piezostack is selected by considering actuation force as well as field-dependent displacement. Subsequently, in order to control spool displacement and flow rate a proportional-derivative (PD) controller is designed based on the $3^{rd}$-order valve system. Control performances such as sinusoidal trajectory tracking of the spool displacement in time domain are evaluated. In addition, the field-dependent flow rate is also presented to verify the required performance of the valve system.

• 한국소음진동공학회논문집
• /
• 제22권10호
• /
• pp.1020-1026
• /
• 2012

This paper proposes a new type of high-frequency directional valve controlled by the piezostack actuator associated with displacement amplifier. As a first step, a dynamic model of directional valve which can operate at 200 Hz with a flow rate of 12 litter/min is derived by considering pressure drop and flow force. As a second step, an appropriate piezostack is selected by considering actuation force as well as field-dependent displacement. Subsequently, in order to control spool displacement and flow rate a proportional-derivative(PD) controller is designed based on the 3rd-order valve system. Control performances such as sinusoidal trajectory tracking of the spool displacement in time domain are evaluated. In addition, the field-dependent flow rate is also presented to verify the required performance of the valve system.

• 오토저널
• /
• 제14권5호
• /
• pp.117-127
• /
• 1992

In this work, the possibility to diagnose valve lashes of an automotive diesel engine via cylinder head vibration/noise analysis is studied. First of all the measurement signals and conditions are selected after considering which signals and conditions are most suitable to diagonse valve lashes. Both accelerometer and microphone are used to measure cylinder head accelerations and acoustic pressure due to valve impact on cylinder head. The signals are measured in both cranking and engine firing conditions. Finally, it was found that acceleration signal obtained in engine operating condition is the most reliable signal to diagnose the valve lash condition. The valve closing angle and the peak acceleration due to valve close are chosen to analyze the valve lash condition. The measured cylinder head acceleration signals are statistically tested to derive information which are useful to judge the valve lash. In conclusion, it was found that the developed technique can be one of feasible methods to diagnose the valve conditions while the engine is in operation.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1942-1947
• /
• 2003

The valve is the key part which governs the efficiency, noise and reliability of the compressor, so the development of analytical model about valve performance is necessary. As the valve leed is opened and closed by pressure pulsation, the flow characteristic of the refrigerant passing the valve is very important. In the present study, a circular disk with inclination is assumed to be the valve reed of a reciprocating compressor and numerical analysis of three dimensional velocity fields are perfomed for the radial flow through the valve model. The effective flow and force area which are required to predict the efficiency of the valve are measured and compared with the numerical analysis in this research.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2003년도 추계학술대회 논문집
• /
• pp.99-102
• /
• 2003

PIV(Particle Image Velocimetry)was used to visualize the interaction of reed valve of the reciprocating compressor. The valve is the key part which governs the efficiency, noise and reliability of the compressor, so the development of analytical model about valve performance is necessary. As the valve reed is opened and closed by pressure pulsation, the flow characteristic of the refrigerant passing the valve is very important. In the present study, a circular disk with inclination is assumed to be the valve reed of a reciprocating compressor, The mean velocity shows the vortical characteristic of this flow. It is found that the back flow is affected by the height of reed valve of reciprocating compressor.

• 유공압시스템학회논문집
• /
• 제6권3호
• /
• pp.1-9
• /
• 2009

Noise reduction for hydraulic pump is strongly demanded in the market with its efficiency and durability. In order to meet this demand, it is necessary to reveal mechanism for noise and relationship between the important factors. In this paper, mathematical model for cylinder pressure which is primary reason of pulsation and sound noise were established, and examined its pressure profile by simulation. Also, the valve plate of three kind types are manufactured and tested for piston pressure, pressure pulsation, and sound power level based on the tentative standard which is officially recognized.

• 한국음향학회:학술대회논문집
• /
• 한국음향학회 2002년도 하계학술발표대회 논문집 제21권 1호
• /
• pp.469-474
• /
• 2002

In recent years, modularization of engine parts has increased the application of plastic products in air intake systems. Plastic intake manifolds provide many advantages including reduced weight, contracted cost, and lower intake air temperatures. These manifolds, however, have some weakness when compared with customary aluminium intake manifolds, in that they have low sound transmission loss because of their lower material density. This low transmission loss of plastic intake manifolds causes several problems related to flow noise, especially when the throttle is opened quickly. The physical processes, responsible for this flow noise, include turbulent fluid motion and relative motion of the throttle to the airflow. The former is generated by high-speed airflow in the splits between the throttle valve and the inner-surface of the throttle body and surge-tank, which can be categorized into the quadrupole source. The latter induces the unsteady force on the flow, which can be classified into the dipole source. In this paper, the mechanism of noise generation from the turbulence is only investigated as a preliminary study. Stochastic noise source synthesis method is adopted for the analysis of turbulence-induced, i.e. quadrupole noise by throttle at quick opening state. The method consists of three procedures. The first step corresponds to the preliminary time-averaged Navier-Stokes computation with a $k-\varepsilon$ turbulence model providing mean flow field characteristics. The second step is the synthesis of time-dependent turbulent velocity field associated with quadrupole noise sources. The final step is devoted to the determination of acoustic source terms associated with turbulent velocity. For the first step, we used market available analysis tools such as STAR-CD, the trade names of fluid analysis tools available on the market. The steady state flows at three open angle of throttle valve, i.e. 20, 35 and 60 degree, are numerically analyzed. Then, time-dependent turbulent velocity fields are produced by using the stochastic model and the flow analysis results. Using this turbulent velocity field, the turbulence-originated noise sources, i.e. the self-noise and shear-noise sources are synthesized. Based on these numerical results, it is found that the origin of the turbulent flow and noise might be attributed to the process of formulation and the interaction of two vortex lines formed in the downstream of the throttle valve. These vortex lines are produced by the non-uniform splits between the throttle valve and inner cylinder surface. Based on the analysis, we present the low-noise design of the inner geometry of throttle body.