• 한국세라믹학회지
• /
• 제35권9호
• /
• pp.974-980
• /
• 1998

This study is concerned with the production of carbon fiber reinforced carbon(C/C) with polyaromatic mesophase pitch as matrix precursor and with the investigation of friction-wear characteristics in ambient air using a constant speed type of friction tester. The main problem in using the polyaromatic mesophase as the matrix precursor is the high viscosity which may limit the complete impregnation of the fiber preform in the vacuum. To solve these problems two dimensional carbon fiber fabrics were infiltrated with meso-phase pitch in the pitch impregnator. After the impregnation and the heat treatment process. C/C com-posites were characterized by density porosity to monitor the influence of high pressure and temperature. It showed that the bulk density was increased and the apparent porosity and the density increasing rate was reduced as repeating the impregnation the carbonization and the heat treatment. The friction-wear charac-teristics of C/C composites were investigated by measuring the average friction coefficient and the specific wear rate as functions friction speed and friction pressure using a constant speed type of friction tester. C/C composite4s showed the average friction coefficient to be reduced as increasing the friction speed and the friction pressure.

• Asian-Australasian Journal of Animal Sciences
• /
• 제31권8호
• /
• pp.1336-1344
• /
• 2018

Objective: This study aimed to observe whether high-pressure processing (HPP) affected aroma development and the degradation rate of umami taste-related ATP breakdown products, specifically inosinic acid in grass-fed beef during vacuum aging. Methods: Strip loin (longissimus lumborum) cuts obtained from six grass-fed Friesian Holstein steers (32 months old) on day 4 post slaughter were vacuum-packed and subjected to pressurization at 300 and 500 MPa for 180 s at $15^{\circ}C{\pm}2^{\circ}C$. The samples were then stored for 4 weeks at $5^{\circ}C{\pm}0.5^{\circ}C$ under vacuum and compared with the control (0.1 MPa). Results: HPP increased the shear force value, promoted moisture loss and lipid oxidation, induced surface paleness, stabilized pH during aging, and reduced bacterial load and growth. The shear force value of 500 MPa-treated samples remained higher than the control after aging, while no significant differences were found between the control and 300 MPa-treated samples. Degradation of inosinic acid and inosine occurred during pressurization, resulting in an increase in hypoxanthine content. However, the degradation rate in HPP-treated samples during aging was slower; therefore, inosinic acid and inosine content remained higher than in control samples. No significant differences were found in hypoxanthine content at the end of aging. HPP intensified the levels of hexanal, octanal, 2-methylbutanal, 3-methylbutanal, benzaldehyde, and 2,5-dimethylpyrazine in cooked-aged beef samples. Conclusion: HPP induced aroma development and delayed the degradation of inosinic acid. However, it also reduced the postmortem tenderization rate.

• 전자공학회논문지D
• /
• 제35D권5호
• /
• pp.63-68
• /
• 1998

The absolute pressure sensor using SDB wafer has been fabricated. the structure of the sensor consists of two wheatstone bridges and a diaphragm. One of the two wheatstone bridges is located on the edge of diaphragm, and the other is located on the center of diaphragm. The diaphragm cavity is sealted in vacuum (~10$^{5}$ Torr) to reduce the effect of temperature due to the vapor in the cavity on the sensitivity of pressure sensor. This is the minor method of temperature compensation method. In this experiment the main compensation method is to use the difference of the two bridge offset voltages. The drift of offset voltage with temperature is reduced by using this method so that temperature charcteristics is improved. In this method the temperature effect in the range of 22~100.deg. C was compensated over 80%.

• 대한기계학회논문집
• /
• 제19권8호
• /
• pp.1999-2011
• /
• 1995

Computer simulation was conducted to study performance characteristics of air-cooled condenser of a double effect absorption heat pump with variations of saturation pressures and mass flow rates of the refrigerant ; volume flow rates, relative humidities and temperatures of the air The vertically installed condenser had the staggered tube array with continuous plate fins of wavy type. When the saturation pressure of the condenser was decreased from 760 torr to 20 torr, heat transfer rates and condensing rates of refrigerant were decreased. If excess refrigerant flows in the condenser, the pressure and saturation temperature of the condenser were increased which makes the refrigerating capacity of an absorption heat pump reduced.

• 콘크리트학회논문집
• /
• 제14권1호
• /
• pp.33-40
• /
• 2002

굳지않은 콘크리트를 진공ㆍ감압시켜 제조하는 진공콘크리트는 내부의 공극을 제거하여 조직의 밀실화를 도모하는 것으로 내마모성 및 강도개선 효과가 있는 것으로 알려져 있으며 선진국에서는 건축물 바닥, 댐콘크리트등에 실용화 된 바 있다. 본 연구는 콘크리트 제조과정에서 진공ㆍ감압 수준의 변화와 배합조건에 따른 콘크리트의 강도 및 슬럼프 등과 같은 물리적 특성변화를 관찰하고자 하였으며 연구 결과는 다음과 같다. 진공ㆍ감압콘크리트의 경우, 공기량 저하에 의한 내부공극 감소로 인한 압밀현상으로 단위용적중량과 압축강도가 증진되는 것으로 나타났으나, 시공성, 취성, 내구성능 등에 있어서는 문제 해결을 위한 지속적인 연구가 필요하다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.866-870
• /
• 2008

In this study, we designed cold gas propulsion system with minimum 0.25 mm nozzle and micro-thrust measurement system to analyze flow characteristic of micro propulsion system in ambient and vacuum condition. Argon and Nitrogen are used for propellant and the result of experiments is compared with CFD analysis and theory. But there is a point where reduced scale versions of conventional propulsion systems will no longer be practical. Therefore, a fundamentally different approach to propulsion systems was taken. That is thermal transpiration based micro propulsion system. It has no moving parts such as lubricants, pressurizing system and can pump the gaseous propellant by temperature gradient only(cold to hot). We are advancing basic research of propulsion system based on thermal transpiration in vacuum conditions and had tried experiment process and theoretical access in advance. To characterize membrane of Knudsen pump, we select Polyimide material that has low thermal conductivity(0.29 W/mK) and can stand high temperature($300^{\circ}C$) for long time. And we fabricated hole diameter 1, 0.5, 0.2, 0.1 mm using precision manufacturing. Experimental results show that pressure gradient efficiency of Knudsen pump is increased to maximum 82% according to Knudsen number and thick membranes are more effective than thin membranes in transition flow regime.

• Korean Chemical Engineering Research
• /
• 제59권4호
• /
• pp.521-531
• /
• 2021

진공가압함침공정(Vacuum Pressure Impregnation, VPI)은 발전기, 전동기 등 대형 회전기에 사용되는 고정자 권선에 에폭시 계열의 레진을 코팅시켜 물성을 강화하는 공정이다. VPI 공정 중 진공과 가압과정에서 에폭시 레진의 기화에 의해 레진 가스가 발생하고, 함침공정이 끝나고 경화를 위해 탱크 개방 시 레진 가스가 제거되지 않고 탱크 밖으로 유출된다. 유출된 레진 가스가 작업장 전체에 확산 시 화재, 폭발 및 호흡기 문제와 같은 안전 환경 문제가 있으므로 공정 내 레진 가스 배출시스템이 필요하다. 따라서, 본 연구에서는 VPI 공정에서 발생한 레진 가스를 배출하는 시스템을 설계하기 위해 전산유체역학(Computational Fluid Dynamics, CFD)을 이용하여 공기 유입구·배출구의 위치에 따른 배출효율에 대한 사례연구를 진행하였다. 본 연구의 최적의 배출시스템을 활용 시 1,800초 이내 90%이상의 레진 가스를 배출할 수 있으며, 레진 가스의 폭발하한계(Low Explosive Limit, LEL)이하로 레진 가스의 분율을 낮출 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.281-285
• /
• 2007

추력기의 성능 등을 예측하려면 기하학적 모양과 압력비를 고려한 노즐 유동 특성을 해석해야 한다. 이 논문에서는 연속체 역학 역학의 가정이 성립하는 한계를 파악하기 위해서 인공위성 자세 제어용으로 사용되는 실제 축대칭 노즐에서의 유동을 계산하였다. 유동은 정상 상태의 비반응 압축성 유동이고 비정렬 격자계를 사용하였다. 추력기의 면적비는 56이고 주위 압력의 진공도를 변경하면서 해석하였는데 그 압력이 $10^{-3}$ 기압 이하가 되면 연속체 역학은 더 이상 타당하지 않게 된다.

• 한국진공학회지
• /
• 제8권4A호
• /
• pp.490-495
• /
• 1999

In 0.18 $\mu \textrm m$ LOGIC device, the etch rate of NMOS polysilicons is different from that of PMOS polysilicons due to the state of polysilicon to manufacture gate line. To control the etch profile, we tested the ratio of $Cl_2$/HBr gas and the total chamber pressure, and also we reduced Back He pressure to get the vertical profile. In the case of manufacturing the gate photoresist line, we used Bottom Anti-Reflective Coating (BARC) to protect refrection of light. As a result we found that $CF_4O_2$ gas is good to etch BARC, because of high selectivity and good photoresist line profile after etching BARC. in the results of the characterization of plasma damage to the antenna effect of gate oxide, NO type thin film(growing gate oxide in 0, ambient followed by an NO anneal) is better than wet type thin film(growing gate oxide in $0_2+H_2$ ambient).

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.110-110
• /
• 1999

Polyvinylidenefluoride (PVDF) is most used in piezoelectric polymer industry. Electrode effect on the electrical properties of PVDF has been investigated. al has been used due to fair adhesion for PVDF. Work function of metal plays an important role on the electrical properties of ferroelectrics for top and /or bottom electrode. However, Al has much lower work function than Pt or Au and so leakage current of Al/PVDF/Al may be large. Pt or Au has not been used for electrode of PVDF system due to poor adhesion. PVDF irradiated by Ar+ ion beam with O2 environment takes good adhesion to inert metal. Contact angle of PVDF to triple distilled water was reduced from 75$^{\circ}$ to 31$^{\circ}$ at 1$\times$1015 Ar+/cm2. Working pressure was 2.3$\times$10-4 Torr and base pressure was 5$\times$10-6 Torr. Pt was deposited by ion beam sputtering and thickness of pt film was about 1000$\AA$. in previous study, enhancing adhesion of Pt on PVDF was shown. in this study, effect of electrode on PVDF will be represented.