• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.515-523
• /
• 2010

Porous SiC candle filter preforms were fabricated by extrusion and ramming process. To fabricate SiC candle filter preform, commercially available F180 mesh ($85\;{\mu}m$) $\alpha$-SiC powder and $44\;{\mu}m$ mullite, $CaCO_3$ powder were used as the starting materials. The candle type preforms were fabricated by vacuum extrusion and ramming process, and sintered at $1400^{\circ}C$ 2 h in air atmosphere. Corrosion test of the sintered candle filter specimens as forming method was performed at $600^{\circ}C$ for 2,400 h in simulated IGCC syngas atmosphere. The effect of forming method on mechanical properties, pore distribution, microstructure and crystalline phase was investigated.

• Journal of the Korean Ceramic Society
• /
• v.46 no.6
• /
• pp.662-667
• /
• 2009

Porous SiC candle filter preforms were fabricated by extrusion and ramming process. To fabricate SiC candle filter preform, commercially available 85 ${\mu}m\;{\alpha}-$-SiC powder and 44 ${\mu}m$ mullite, CaC$O_3$ powder were used as the starting materials. The candle type preforms were fabricated by vacuum extrusion and ramming process, and sintered at $1400{^{\circ}C}$ 2 h in air atmosphere. The effect of forming method on porosity, density, strength (flexural and compressive strength) and microstructure was investigated. Also, corrosion test of the sintered candle filter specimens as forming method was performed at $600{^{\circ}C}$ in IGCC syngas atmosphere. The sintered SiC filter which was formed by ramming process has more higher density and exhibit higher strength than extruded filter. Its maximum density and 3-point bending strength were 2.00 g/$cm^3$ and 45 MPa, respectively.

• Korean Journal of Materials Research
• /
• v.11 no.7
• /
• pp.590-598
• /
• 2001

SiCp/pure Al and SiCp/2024Al MMCs were fabricated by in-situ VHP process designed specially just in this study which is composed of the vacuum hot press at range from R.T. to $500^{\circ}C$ and the continuous extrusion without canning process at $520^{\circ}C$. It was investigated the effect of SiC particle size, volume fraction and extrusion ratio on the tensile properties and micro structure in auf composites. In case of the 10:1 extrusion ratio, but SiCp/pure Al and SiCp/2024Al composites were shown a sound appearance and a good micro structure without crack of SiCp as well as uniform distribution of SiCp. However, in case of the 16:1 extrusion ratio, the number of cracked SiC particles more than increased in a higher volume fraction composite and 2024Al matrix composite compared with pure Al matrix one. The tensile strength of the composites reinforced smaller SiCp was higher than that of the bigger SiCp reinforced in same volume fraction and extrusion ratio.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.04a
• /
• pp.23-26
• /
• 2003

Solid-state extrusion technique was employed for the improvement of mechanical properties of polylactic acid (PLLA) widely used as biodegradable internal fixation devices currently. Cylindrical billets were machined out from the vacuum compression-molded PLLA to have various diameters, and solid-state extrusion of the billets was performed at various drawing rates and at the extrusion temperature of $130^{\circ}C$. Throughout the whole processes the decrease in molecular weight was significantly suppressed to be about $10\%$. Flexural modulus and strength of PLLA increased up to 8.3 GPa and 221 MPa, respectively. Studies on the orientation and crystallinity of extruded PLLA could reveal the effects of billet morphology, draw ratio, and drawing rate on the flexural strengths of PLLA.

• Journal of Korea Foundry Society
• /
• v.20 no.2
• /
• pp.110-115
• /
• 2000

In this study, the powders of Mg-3wt%Al-1wt%Zn-1wt%MM alloy were produced under vacuum condition by the inert gas atomization and the rapidly solidified powders were consolidated by the vacuum hot extrusion. Then the structural change of powders during extrusion was investigated. The effects of misch metal addition to AZ31 on mechanical properties of extruded bars were also examined. During extrusion of the rapidly solidified powders, their dendrite structure was broken into fragments and remained as grains of 2 ${\mu}m$ size in extruded bar. The Mg-Al-Ce intermetallic compounds formed in the interdendritic regions of powders were broken finely, too. The yield stress, tensile strength and ductility obtained in as-extruded Mg-3wt%Al-1wt%Zn-1wt%MM alloy were ${\sigma}_{0.2}=325$ MPa, ${\sigma}_{T.S.}=417$ MPa and ${\varepsilon}=16.8%$. All of these improvements on mechanical properties result from the refined micostructure and second-phase dispersions.

• Proceedings of the CALSEC Conference
• /
• 2001.08a
• /
• pp.105-109
• /
• 2001

성형의 종류 ◈금속 성형 ㆍ 스탬핑(Stamping) ㆍ 정밀 블랭킹(Fine Blanking) ㆍ 딥 드로잉(Deep Drawing) ㆍ 다이캐스팅(Die Casting) ㆍ 인베스트먼트 주조(Investment Casting) ㆍ 분말 야금(Power Metallurgy) ㆍ 인발(Wire Drawing) ㆍ 압출(Extrusion) ㆍ 단조(Forging) ㆍ ㆍ코이닝(Coining) ㆍ... ◈비금속 성형 ㆍ 사출(Injection) ㆍ 압축(Compression) ㆍ 블로우 성형(Blow Molding) ㆍ 진공 성형(Vacuum Molding) ㆍ 발포 성형(Foam Molding) ㆍ 피복(Encapsulation) ㆍ 회전식(Rotational) ㆍ 주조(Casting) ㆍ 적층(Laminating) ㆍ 압출(Extrusion) ㆍ...(중략)

• Elastomers and Composites
• /
• v.57 no.3
• /
• pp.114-120
• /
• 2022

The tensile properties of the extruded PC film were measured in the extrusion direction and perpendicular to the extrusion direction. The measured properties were the elastic modulus and Poisson's ratio at the glass transition temperature of PC. The measured orthotropic properties of the film were used for the computer simulation of vacuum forming. In this simulation, three mold shapes were tested: dome, trapezoid, and cubic, and the vacuum was applied between the mold surface and the heated film. The stress, strain, thickness, and stretch ratio distributions of the film in different mold shapes were observed and compared. The thermoforming simulation method used in this study and the obtained results, considering the determined orthotropic properties, can be applied to the thermoforming of various three-dimensional shapes.

• Food Science and Preservation
• /
• v.14 no.5
• /
• pp.451-456
• /
• 2007

The vitamin C content in extruded comstarch matrix was shown to depend on extrusion process variables (barrel temperature and water content), the packaging method, and the storage period. In addition, loss rates of vitamin C under different processing conditions were calculated. Extrusion process variable were barrel temperature ($80^{\circ}C,\;90^{\circ}C,\;100^{\circ}C$ and $110^{\circ}C$), and water content (25% 30% both w/w). The vitamin C content decreased as barrel temperature increased from $80^{\circ}C$ to $110^{\circ}C$ and water content increased from 25% to 30% when either LDPE plastic film packaging or ON film vacuum packaging were employed. As barrel temperature and water content increased, vitamin C decreased in comstarch packed in either LDPE film or ON film. As temperature increased, vitamin C loss rate increased under both packaging conditions, but the loss tate was only 50% of the LDPE film packaging rate when ON film vacuum packaging was used. In conclusion, the higher the temperature, and the greater the water content, the less vitamin C was inactivated during extrusion cooking, although the loss rah of vitamin C became faster as temperature and water content rose. In conclusion, extrusion process could be applied for making vitamin C matrix to extend vitamin C preservation.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.118.1-118.1
• /
• 2016

포항가속기연구소 PLS-II 저장링에 설치 운용을 위한 타원편광 언듈레이터(EPU114)용 초고진공 진공 챔버는 전체를 기계가공 후 용접하여 제작하는 기존의 방식을 바꾸어 알루미늄 압출 공법을 적용한 진공 챔버의 개발과 본제품 제작을 완료하였다. 압출 공법을 이용한 초고진공용 진공 챔버 제작은 기계가공 및 용접비용의 절감과 동일 형상의 진공 챔버를 상대적으로 쉽게 대량 생산을 할 수 있는 장점이 있다. 알루미늄 압출형 초고진공 진공 챔버의 기계, 진공 특성을 달성하기 위하여 정밀금형 제작기술, 특수압출기술, 표면처리기술 등이 필수적이다. 본 발표에서는 초고진공 진공 챔버 개발을 위하여 적용된 압출 공법의 소개와 함께 압출 공법이 적용된 타원편광 언듈레이터(EPU114)진공 챔버의 제작, 초고진공 진공달성, 설치 등의 과정을 내용으로 한다.

• Journal of Powder Materials
• /
• v.5 no.4
• /
• pp.340-344
• /
• 1998

Along with the growth of conventional ferrous powder metallurgy (PM), PM of aluminum alloys has been intensively investigated in Japan. Although rapidly solidified aluminum alloy powder was first used in the USA,/sup 1)/ commercialization for consumer market was first realized in Japan./sup 2)/ In order to achieve the viable cost-performance including Near Net Shape (NNS) formability, we developed three processes, powder extrusion, powder forging and sintering. The new powder extrusion process does not use either capsulation or vacuum degassing. The new powder forging does not need lateral flow. The new sintering process does not use liquid phase. The performance achieved by the processes is outstanding mechanical or physical properties that has potential to substitute cast iron, steel, titanium Metal Matrix Composite (MMC) or Ingot Metallurgy (IM) aluminum alloys. Cooperation with customers, powder suppliers and research associations contributed to the advancement of PM aluminum alloys in Japan.