• Journal of radiological science and technology
• /
• v.44 no.3
• /
• pp.173-181
• /
• 2021

The purpose of this study was to reduce dose while maintaining image quality during digital radiographic examination of paranasal sinus by using the automatic exposure control (AEC) system. The tube voltage was set as six stages that increased by about 10 kVp to 70 kVp, 81 kVp, 90 kVp, 102 kVp, 109 kVp and 117 kVp. And then the AEC system conditions were consisted of 9 setting environments, that change mode of the sensitivity (S200, S400, S800) and the density (+2.5, 0, -2.5). We measured automatically exposed tube current (mAs) under 54 conditions with combined these, and assessed SNR and PSNR through the acquired images. In addition, four radiologists performed a qualitative assessment of the acquired images for each combination on a five-point scale of the Likert. As a result, the lowest dose and the highest values of SNR and PSNR in images with a qualitative assessment more than 4 point were the AEC control factors of 90 kVp, S800, D2.5. We applied this condition to the clinical trial, it showed an effect of 83.1% reduction in exposure radiation dose (mR). Therefore, AEC system could be used as dose reduction technology if it understood and used related regulatory factors and physical characteristics.

• Journal of the Korean Society of Radiology
• /
• v.16 no.2
• /
• pp.131-139
• /
• 2022

The purpose of this study was to insert a pedicle screw into a pig thoracic vertebrae, a general CT scan(Non MAR), and a thoracic axial image obtained with the Metallic Artifact Reduction for Orthopedic Implants (O-MAR) to reduce artifacts. The image obtained by reconstructing the algorithm (Standard, Soft, Bone, Detail) was used using the image J program. Signal to noise ratio(SNR) and contrast to noise ratio(CNR) were compared and analyzed by obtaining measured values based on the given equation. And this study was to investigate tube voltage and algorithm suitable for CT scan for thoracic pedicle screw insertion. As a result, when non-MAR was used, the soft algorithm showed the highest SNR and CNR at 80, 100, 120, and 140 kVp, On the other hand, when MAR was used, the standard algorithm showed the highest at 80 kVp, and the standard and soft algorithms showed similar values at 100 kVp. At 120 kVp, the Soft and Standard algorithms showed similar values, and at 140 kVp, the Soft algorithm showed the highest SNR and CNR. Therefore, when comparing Non-MAR and MAR, even if MAR was used, SNR and CNR did not increase in all algorithms according to the change in tube voltage. In conclusion, it is judged that it is advantageous to use the Soft algorithm at 80, 100, 120, and 140 kVp in Non MAR, the Standard algorithm at 80 and 100 kVp in MAR, and the Soft algorithm at 120 and 140 kVp. This study is expected to serve as an opportunity to further improve the quality of images by using selective tube voltage and algorithms as basic data to help evaluate images of pedicle screw CT scans in the future.

• Journal of Korean Academy of Oral and Maxillofacial Radiology
• /
• v.20 no.2
• /
• pp.265-276
• /
• 1990

The purpose of this experiment was to evaluate radiographic interpretation, of various sized 60 periapical and 60 cancellous lesions in 10 mandibular sections of 5 dogs according to kVp (65, 70, 75, 80 and 85 kVp). The results were as follows; The change of kilovoltage within 65kVp-85kVp range did not have influence on the radiographic interpretation of the same-sized bony defects at the constant radiographic density (p> 0.05). When the bony defects were less than the size of No.2 round bur, radiographic interpretation of bony defects prepared with No.2 round bur was easier than those prepared with No. 1 round bur at 80-85kVp in periapical region (p<0.05). However, in cancellous bone, this radiographic interpretation was easier at 65-75kVp (p<0.05). There were significant differences in the radiographic interpretation between the defects confined only to the cancellous, bone and the defects involved in the compact bone (p<0.05). However there were no significant differences between the defects confined only to the cancellous bone and the defects involved in junctional area of cancellous and compact bone (p>0.05). From the results of densitometric analysis, there was a difference in densitometric measurements at the same radiographic interpretation scores, and aluminum equivalent differences of 0.15-1.66㎜ thickness were needed for radiographic interpretation.

• Journal of the Korean Society of Radiology
• /
• v.17 no.4
• /
• pp.489-495
• /
• 2023

Radiation shielding facilities are constructed in locations where diagnostic radiation generators are installed, with the aim of preventing exposure for patients and radiation workers. The purpose of this study is seek to compare and validate the trend of attenuation thickness of lead, the primary material in these radiation shielding facilities, at different maximum tube voltages by Monte Carlo simulations and measurement. We employed the Monte Carlo N-Particle 6 simulation code. Within this simulation, we set a lead shielding arrangement, where the distance between the source and the lead sheet was set at 100 cm and the field of view was set at 10 × 10 cm². Additionally, we varied the tube voltages to encompass 80, 100, 120, and 140 kVp. We calculated energy spectra for each respective tube voltage and applied them in the simulations. Lead thicknesses corresponding to attenuation rates of 50, 70, 90, and 95% were determined for tube voltages of 80, 100, 120, and 140 kVp. For 80 kVp, the calculated thicknesses for these attenuation rates were 0.03, 0.08, 0.21, and 0.33 mm, respectively. For 100 kVp, the values were 0.05, 0.12, 0.30, and 0.50 mm. Similarly, for 120 kVp, they were 0.06, 0.14, 0.38, and 0.56 mm. Lastly, at 140 kVp, the corresponding thicknesses were 0.08, 0.16, 0.42, and 0.61 mm. Measurements were conducted to validate the calculated lead thicknesses. The radiation generator employed was the GE Healthcare Discovery XR 656, and the dosimeter used was the IBA MagicMax. The experimental results showed that at 80 kVp, the attenuation rates for different thicknesses were 43.56, 70.33, 89.85, and 93.05%, respectively. Similarly, at 100 kVp, the rates were 52.49, 72.26, 86.31, and 92.17%. For 120 kVp, the attenuation rates were 48.26, 71.18, 87.30, and 91.56%. Lastly, at 140 kVp, they were measured 50.45, 68.75, 89.95, and 91.65%. Upon comparing the simulation and experimental results, it was confirmed that the differences between the two values were within an average of approximately 3%. These research findings serve to validate the reliability of Monte Carlo simulations and could be employed as fundamental data for future radiation shielding facility construction.

• Journal of KIISE:Information Networking
• /
• v.27 no.2
• /
• pp.187-196
• /
• 2000

Failures in ATM networks can occur at virtual path (VP) links, virtual path switches, and virtual channel (VC) switches. Restoration schemes have been proposed for VP link and VP switch failures, however, none for VC switch failures. In general, VC switches are used for edge nodes in protection domains. Since even only one VC switch failure can cause a critical problem, new restoration schemes for VC switch failures are highly required. Restoration schemes at the VP level proposed so far can be categorized into those using the flooding algorithm and those using the backup virtual path (BVP) concept. Even though the latter cannot handle unpredictable failures, it has some advantages such as fast restoration and low spare capacity requirement. In this paper, we propose new restoration schemes using a new type of BVPs to handle VC switch failures. The simulation results show that the proposed schemes can restore virtual connection failures due to VC switch failures without degrading restorability for VP failures.

• Journal of the Korean Society of Radiology
• /
• v.11 no.1
• /
• pp.63-68
• /
• 2017

To reduce the exposure dose in head CT, the use of low tube voltage is required. However, increasing noise may cause errors in the second data processing. In this study, we proposed a method to reduce noise by using low tube voltage. Experimental results show that the noise level is high at 100kVp and lowest at 140 kVp. The dose was lower at 100 kVp and higher at 140 kVp. As a result of applying the wavelet according to the threshold value, the noise value in the wavelet Th30 decreased to 4.51. Using the parameter condition(100 kVp, rotation time 0.5 sec, dose: 40.64 mGy) and the wavelet Th 30, the dose reduction of 65.3% was possible. We believe that applying the proposed method to head CT images will help to patient safety and interpret accurate information.

• Pediatric Gastroenterology, Hepatology & Nutrition
• /
• v.9 no.2
• /
• pp.147-152
• /
• 2006

Purpose: Efficacy of the new rotavirus vaccines ($Rotarix^{(R)}$, $RotaTeq^{(R)}$) recently developed can be affected by the rotavirus genotypes prevalent in communities. We performed this study to identify the recent distribution of rotavirus genotypes prevalent in Jeju. Methods: Genotyping of human rotaviruses was performed using 81 samples collected from 154 inpatients and outpatients with rotavirus gastroenteritis at Cheju National University Hospital between July 2005 and June 2006. All six (1, 2, 3, 4, 8, 9) G serotypes were identified by amplification of segments of the gene for VP7 using the reverse transcription-polymerase reaction (RT-PCR). Results: The results of RT-PCR for 81 samples were all positive. G typing of the VP7 protein showed that G1 was the most dominant circulating genotype (65.5%) followed by G2 (14.8%), G3 (13.6%), G8 (1.2%), G9 (1.2%), G4 (0%), and a combination of G1/G3 (3.7%). Conclusion: This distribution of rotavirus VP7 genotypes in Jeju is different from that in other domestic areas; the most dominant circulating genotype was G1.

• Journal of radiological science and technology
• /
• v.38 no.2
• /
• pp.107-114
• /
• 2015

The purpose is reducing radiation dose while maintaining of image quality in liver dynamic CT(LDCT) scan, by protocols generally used and the tube voltage set at a low level protocol compared to the radiation dose and image quality. The target is body mass index, 18.5~24 patients out of 40 patients who underwent the ACT(abdominal CT). Group A(tube voltage : 120kVp, SAFIRE strength 1) of 20 people among 40 people, to apply the general abdominal CT scan protocol, group B(tube voltage : 100kVp, apply SAFIRE strength 0~5) was 20 people, set a lower tube voltage. Image quality evaluation was setting a region of interest(ROI) in the liver parenchyma, aorta, superior mesenteric artery (SMA), celiac trunk, visceral fat of arterial phase. In the ROI were compared by measuring the noise, signal to noise ratio(SNR), contrast to noise ratio(CNR), CT number. In addition, qualitative assessments to evaluate two people in the rich professional experience in Radiology by 0-3 points. We compared the total radiation dose, dose length product(DLP) and effective dose, volume computed tomography dose index(CTDIvol). The higher SAFIRE in the tube voltage 100 kVp, noise is reduced, CT number was increased. Thus, SNR and CNR was increased higher the SAFIRE step. Compared with the tube voltage 120kVp, noise, SNR, CNR was most similar in SAFIRE strength 2 and 3. Qualitative assessment SAFIRE strength 2 is the most common SAFIRE strength 2 the most common qualitative assessment, if the tube voltage of 100kVp when the quality of the images better evaluated was SAFIRE strength 1. Dose was reduced from 21.69%, in 100kVp than 120kVp. In the case of a relatively high BMI is not LDCT scan, When it is shipped from the factory tube voltage is set higher, unnecessary radiation exposure when considering the reality that is concerned, when according to the results of this study, set a lower tube voltage and adjust the SAFIRE strength to 1 or 2, the radiation without compromising image quality amount also is thought to be able to be reduced.

• The Journal of the Korea Contents Association
• /
• v.15 no.1
• /
• pp.316-323
• /
• 2015

In this study, we analyzed radiation dose and MTF with setting of Ion chamber and changing kVp so that we are able to suggest acquiring optimized diagnostic images and minimizing patient dose. we assumed right lateral decubitus position among chest decubitus projection and set 7 combination of Ion chamber. By changing kVp(100, 110, 120, 130kVp), we exposed x-ray five times respectively and calculated average value after measuring entrance dose. we input the entrance dose value to PCXMC Monte carlo simulation tool and calculated organ dose and effective dose. Then we did physical image evaluation with MTF for the purpose to compare image quality. As a result, the high kVp, entrance dose is reduced. As change of ion chamber, when selecting second ion chamber, both organ dose and effective dose were the lowest. In contrast, selecting first ion chamber was the highest. MTF is superior to set second Ion chamber and using 120 kVp. Consequently, when taking chest right lateral decubitus using Digital radiography, the optimized combination which have both reducing dose efficiently without declining image quality and aquring good qualified image is set 120 kVp and selecting second Ion chamber.

• The Journal of Korean Society of Virology
• /
• v.28 no.2
• /
• pp.165-174
• /
• 1998

Characterizations of the VP4 (P type) and VP7 (G type) genes of Korean isolates of bovine rotavirus were performed using RT-PCR/RFLP and nucleotide sequencing analysis. After RT-PCR amplification of partial length (1094bp) of the VP4 and full length (1062bp) of the VP7 genes, amplified PCR products were digested with restriction endonucleases and digestion patterns were compared with those of reference rotaviruses. With the VP4 genes, four RFLP (A-D) profiles were observed; three (A, Band C) were the same as those of bovine rotavirus NCDV (P[1]), IND (P[5]) and B223 (P[11]), respectively. Profile D was the same as that of porcine rotavirus OSU (P[7]). With the VP7 genes, five RFLP profiles (I-V) were observed; three of them (I, II and III) were the same as those of bovine rotavirus NCDV (G6), Cody 1-801 (G8), and B223 (G10), respectively. Profile IV and V were atypical to those of reference bovine rotaviruses used in this study. These two profiles were identified as G6 and G5, respectively, after analyzing and comparing the nucleotide sequences. The G typing analysis revealed that 61.9% (26/42) were G6, which included G6 subtype; 28.6% (12/42) were G5; 7.1% (3/42) were G10; 2.4% (1/42) were G8. The P typing analysis revealed that 54.8% (23/42) were P[5]; 28.6% (12/42) were P[7]; 11.8% (5/42) were [11]; 4.8% (2/42) were P[1]. Our results showed that G6/P[5] were the most prevalent rotaviruses in diarrheic calves in Korea. Also, this is the first report that G5/P[7] rotaviruses were identified from cattle with diarrhea.