• 한국연소학회:학술대회논문집
• /
• 한국연소학회 1998년도 제17회 KOSCI SYMPOSIUM 논문집
• /
• pp.91-101
• /
• 1998

The effect of secondary flow on both methane/air and propane/air premixed flame was investigated experimentally. By changing the radius of curvature, various flame behavior was observed. In the V-bend nozzles, flame surface is deformed from axisymmetry. As the exit velocity increased, flame lifted off partially. When the radius of curvature of the V-bend increased, the region where premixed flame is entirely on the rim increased. Since the axial velocity field is changed due to the secondary flow effect, comparison of V-bend and straight tube with the same diameter shows larger V-bend nozzle exit velocity for both flash back and flame blowout. The flame characteristics are mapped with a equivalence ratio, a velocity, and a nozzle radius of curvature. To identify physical reasoning on the flame surface deformation, numerical calculations are conducted. OH radical distributions in flames are visualized by PLIF technique.

• 한국전기전자재료학회논문지
• /
• 제35권5호
• /
• pp.494-498
• /
• 2022

In this study, SiO₂ 20 phr, ATH 70 phr, and platinum flame retardant were mixed with raw silicone rubber and -10 kV was applied to measure electrostatic charge attenuation voltage, surface resistance, and volume resistance, and the following conclusions were obtained. When the platinum flame retardant was 0 phr, the humidity 74.6% and the temperature was 21.8℃, the potential was half-reduced to 0.63 kV, 0.57 kV, and 0.44 kV when the applied voltage was changed from -10 kV to -8 kV, and the time halved to 50% was increased to 2.40 seconds, 2.47 seconds, and 2.61 seconds. It was confirmed that as the platinum flame retardant increased from 0.1 to 0.3 phr, the potential half-reduced to 0.67 kV, 0.60 kV, and 0.595 kV decreased, and the charge potential attenuation time half-reduced to 50% decreased to 3.44 seconds, 1.78 seconds, and 1.60 seconds. It was confirmed that the surface resistance increased as the humidity decreased, and the volume resistance decreased as the platinum flame retardant increased.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.447-448
• /
• 2008

The goal of this study is to find flame dynamic behavior using a transverse fuel injection in a model combustor, and is to investigate main causes of unstable combustion in a liquid-fueled combustor. For transverse fuel injection into air cross flow, spray result shows similar tendency with Wu et al.[1998] until spray arrives at flame-holder. However, passing through flame-holder, fuel inflow into recirculation region of flameholder is not sufficient so it makes large difference between shear flame and recirculation flame behind flameholder. In combustion tests, the stable flame shows a kind of shear flames and low peaks of dynamic pressure frequencies. On the other hand, unstable flame shows periodic detached flame in recirculation zone and a strong peak of dynamic pressure frequency. The instability frequency is highly affected by influx air velocity, air temperature, equivalence ratio and wake or vortex shedding frequency behind the flameholder.

• 한국안전학회지
• /
• 제27권6호
• /
• pp.70-77
• /
• 2012

Experimental investigations were performed to examine the characteristics of propagating flame fronts around multiple bars within a rectangular chamber. The explosion chamber is 400 mm in height, $700{\times}700mm^2$ in cross-section and has a large top-venting area, $A_v$, of $700{\times}210mm^2$. This results in a value of 0.44 for $A_v/V^{2/3}$ and a L/D value of 0.57. The multiple obstacles of length 700 mm with a blockage ratio of 30 % were placed within the chamber. Temporally resolved flame front images were recorded by a high speed video camera to investigate the interaction between the propagating flame and the obstacles. Results showed that the flame propagation speeds before the flame impinges onto the obstacle almost equal to the laminar burning velocity. As the propagating flame impinged on the obstacle, the central region of flame began to become concave, this resulted in the flame deceleration in the region. As the flame interacted with the modified flow filed generated behind the central obstacle, the probability density functions(PDFs) of the local flame displacement speed were extensively distributed toward higher speeds.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1372-1377
• /
• 2003

The stabilization of propane/air lean premixed flames by a heated cylindrical rod is investigated experimentally. The flame stability limits, heat flux, surface temperatures, equivalence ratios, and mixture velocities are measured in order to understand the role of heat flux or surface temperature on the flame stabilization of lean premixed flames. The flame stability limits are lowered by a heated cylindrical rod and extended even below the flammability limit of propane/air mixture when sufficient heat flux is provided. The flame stability limit decreases with the increase of heat flux or surface temperature and decreases with the higher mixture velocity. The diameter of cylindrical rod, however, dose not significantly affect the flame stability limit. The laminar flame speed has been measured for ultra lean propane/air premixed flames. The flame stabilization by a heated cylindrical rod provides the useful tool for the measurement of flame speed under very fuel-lean conditions.

• 한국연소학회:학술대회논문집
• /
• 대한연소학회 2003년도 제27회 KOSCO SYMPOSIUM 논문집
• /
• pp.185-193
• /
• 2003

Basic flow fields of two dimensional V flames were examined as a preliminary work to study the instability of premixed flame with vorticity generation. Laminar premixed propane and methane flame were anchored by electrically heated wire to make two dimensional V flames. Flow fields were measured mainly by PIV(Particle Image Velocimetray) and the results were compared with those obtained by LDV(Laser Doppler Velocimetry) to confirm their reliability. Because the curvatures of V flames are so small, V flames were locally assumed to be inclined planar flames in gravitational field. The measured flow fields were locally compared with those of analytical solutions, which showed the qualitatively similar results. In downstream region, the vorticity fields were nearly constant except region near the center line, which support the assumption of locally one dimensional flame. Besides it was tried to find experimentally the similarity of flow fields in downstream region. Finally, stability diagram of propane and methane flames were drawn for the equivalence ratio less than one and the wide range of mean velocity.

• 한국안전학회지
• /
• 제17권2호
• /
• pp.112-117
• /
• 2002

메탄-공기의 비예혼합 대향류 확산화염 차폐가스가 화염구조에 미치는 영향을 수치적으로 조사하였다. 20 $s^{-1}$의 저변형율, 메탄가스 19%와 질소 79%의 혼합가스 연료와 공기의 확산화염을 대상으로 하였다. 질소차폐가스의 속도의 차폐가스의 유무에 따른 화염의 형태와 중심선상의 온도 및 축방향 속도의 분포를 비교하였다. 정상중력에서 $V_{S}/V_{F}{\leq}2$일 때 차폐가스의 유동이 화염구조에 미치는 영향은 무시할 수 있었다. 정상중력에서 차폐가스가 없는 경우의 화염형태와 그 위치는 차폐가스가 있는 경우와 다르지만, 무중력에서는 중심선상에서 차폐가스의 영향이 거의 없었다.

• Elastomers and Composites
• /
• 제55권1호
• /
• pp.40-45
• /
• 2020

In this study, the mechanical and flame-retardant properties of ethylene-propylene-diene-termonomer (EPDM) based rubber compounds and various other environmentally friendly inorganic flame retardants were investigated. Alumina trihydrate (ATH) and magnesium hydroxide (MDH) were used as inorganic flame retardants. The mechanical properties after thermal oxidation aging and the flame-retardant properties of the EPDM compounds were measured using a moving die rheometer, a universal testing machine, a compression set, and a UL 94 V flammability test. We focused on how the properties were affected by the type and amount of flame retardants. The results demonstrated that the optimal mechanical and flame-retardant V-0 grade properties were obtained at an ATH content of 200 phr.

• 청정기술
• /
• 제23권4호
• /
• pp.378-387
• /
• 2017

영구적 난연성기를 함유한 에폭시 수지를 얻기 위하여, 본 연구에서는 디하이드록시를 함유한 인 화합물[10-(2,5-dihydroxyphenyl)-9,10-dihydro-9-oxa-10-phospha phenanthrene-10-oxide, DOPO-HQ]과 디하이드록시를 함유한 실리콘 화합물(polydimethylsiloxane, hydroxyl terminated, PDMS)를 경화하지 않은 에폭시 프리폴리머(diglycidyl ether of bisphenol A, DGEBA)와 반응시킨 다음, 경화제(4,4-diaminodiphenylmethane, DDM)를 사용하여 경화반응 시킨 에폭시 수지를 제조하였다. 제조된 에폭시 수지의 각종 특성을 적외선 분광분석기(FTIR), 시차주사열량기(DSC), 열중량 분석기(TGA), 한계산소지수(LOI)/수직 연소 시험(UL 94-V test), 인장 및 충격 시험을 이용하여 분석하였다. 그리고 사용한 인 및 실리콘 화합물의 함량이 에폭시 경화물의 열적/기계적 성질 및 난연성에 미치는 영향을 조사하였다. 인 및 실리콘 성분이 함유된 에폭시 수지의 열적 및 기계적 물성이 단순 에폭시 수지의 물성에 비교하여 크게 향상되었다는 것을 알 수 있었다. 그리고 인 및 실리콘을 함유한 모든 에폭시 수지는 29.9 ~ 31.8%의 LOI 및 V-0 수준의 UL 94-V로 난연성 기준(LOI: 30% 이상, UL 94-V: V-0)을 통과한 반면, 단순 에폭시 수지는 LOI: 21.4% 및 UL 94-V: no rating으로 난연성 기준에 크게 못 미치는 것을 알 수 있었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2001년도 제16회 학술발표회 논문초록집
• /
• pp.43-46
• /
• 2001

Dump type Ram-combustor의 성능 개선을 위한 화염 안정화 장치인 V-gutter를 장착하고 그 영향을 파악하기 위한 본 실험에서 V-gutter가 없고, Ram-combustor의 길이가 짧을 경우($L_c$=300mm)에는 출구중앙의 온도가 감소하는 경향이 나타났고 Ram-combustor의 길이가 증가하면($L_c$=500mm) 중앙에서 온도가 감소되는 현상은 나타나지 않지만 화염은 아직도 Ram-combustor의 아래 부분에 치우쳐있다. V-gutter가 장착된 경우 Ram-combustor 출구의 온도 분포는 훨씬 균일하게 분포되었다. 그리고 Ram-combustor의 길이가 짧을 때($L_c$=300mm) 연소효율의 경우 V-gutter을 장착한 경우 연소효율은 약간 증가하지만 큰 영향은 없음을 알 수 있다.