• 한국태양에너지학회 논문집
• /
• 제23권4호
• /
• pp.63-70
• /
• 2003

It is very important to improve the insulation performance of curtain wall anchoring unit since it is composed of materials with high thermal conductivity, such as aluminium, steel and so on. This study aims to evaluate the heating energy performance and economical efficiency of various alternatives which are different in position and material of insulation. As results, alternative of inserting the urethane washer & pad and coating the anchoring unit with urethane foam can improve the heating energy performance and L.C.C(Life Cycle Cost) by 6.33% and 0.95%, respectively, as compared with the existing case.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.599-605
• /
• 2009

The aim of the present study is the characteristics of bridge rubber pads and suggested how to determine the stiffness the pads. A disk bearing is operated as an elastic bearing in the vertical direction and is composed of a Polyether Urethane (polyurethane) disk for elastic support and Polytetrafluoroethylene (PTFE) to accommodate movement. Static tests are conducted in a laboratory to determine the static behavior of a Polyurethane disk. Finite Element (FE) analysis is also performed to verify the static performance. For dynamic behavior, four disk bearings having the identical Polyurethane disk used in the static tests are installed in a full size railway bridge and tested under a running locomotive. From the tests results, the static and dynamic stiffness of disk bearings are estimated and compared with each other. In the procedure to estimate the stiffness of a pad, the dead load(pre-load) of a bridge and live load of a vehicle are considered.

• 대한기계학회논문집A
• /
• 제33권4호
• /
• pp.337-345
• /
• 2009

This paper investigates the reliability of district heating pipes at thermo-elastic fatigue loading. District heating pipes, subjected to $120^{\circ}C$ and $16kg_f/cm^2$ due to water distributing service through inside the pipes, should endure long term cyclic thermal-mechanical loadings. The heating pipes are the co-centric tubes of steel pipe, poly urethane(PUR) insulator, and high density poly ethylene(HDPE) case. On installation, foam pad is externally wrapped for accommodating stress reduction near the bend sections of pipes. However, there have been frequent reports on the failures of bend sections in the middle of long term service. This study scrutinizes the observed failures near the bend sections through applying the finite element methods. Specially in this study, heating pipes are studied on the influence of foam padding on failures and proposed new designs for reinforced bend without foam pad.

• Elastomers and Composites
• /
• 제43권3호
• /
• pp.173-182
• /
• 2008

고무나 우레탄과 같은 고 탄성력을 이용하여 튜브를 임의의 형상으로 성형하는 고 탄성체 성형방법은 타 공정에 비해 높은 치수 정밀도와 생산 공정의 단축, 에너지 절감 등을 기대할 수 있는 차세대 성형기술이라 할 수 있다. 본 연구에서는 탄성체에 대한 소재 물성시험과 특성평가를 통해 고 탄성체 성형에 적합한 소재를 선정하고 시험으로 얻어진 응력-변형률을 이용하여 비선형 재료상수를 결정하여 성형해석에 필요한 물성 데이터를 확보하였다. 또한, 랙튜브에 대한 유한요소해석을 통해 탄성체의 두께변화에 따른 공정변수의 영향을 검토하였다.

• 한국산업보건학회지
• /
• 제24권3호
• /
• pp.281-292
• /
• 2014

Objectives: The aim of this case study is to verify the chemical exposure reductions for various chemicals by substituting the ingredients of raw materials in a polyurethane(PU) foaming industry. The PU foaming process was making various passenger car seats from chemicals such as toluene diisocinate(TDI), methylene bisphenyl isocyanate(MDI) and polyols. Methods: Basic process data and workers' health effects could be gathered by interviewing managers and reviewing previous exposure monitoring data. Amine, aldehyde and isocyanate chemicals were analyzed following the NIOSH-NMAM. Area sampling methods rather than personal sampling were introduced for this field investigation. Results: Two amines, triethylene diamine(TEDA) and N,N,N',N'-Tetramethyl-1,6- hexanediamine(TMHDA) were identified in raw polyol, cured PU foam and air. The average concentrations of TEDA and TMHDA showd less than 1 ppm by area sampling; however, that caused halovision among workers in PU-PAD process. Aldehydes and isocyanates were detected in the air while the concentrations were relatively low compare to occupational exposure limits. Successful raw material substitution from nonreactive amine to reactive amine could reduces air-borne amine and aldehyde levels by about 70%. Halovision had been disappeared successfully in the process. Conclusions: Several amines caused halovision among workers in PU-PAD process, especially during summer season in spite of relatively low levels. Combination of reactive amines into urethane foam could reduced vapor generation into air, which resulted in the elimination of eye troubles in the process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.281-284
• /
• 2009

Flexible forming process for sheet metal using reconfigurable die is introduced based on numerical simulation. Numerical simulation of sheet metal forming process is carried out by using flexible dies model instead of conventional matched die set. Elastic cushion which has high resilience behavior from excessive deformation are inserted between forming punches and blank material for smoothing the forming surface which has discrete due to characteristics of the flexile die. As an elastic cushion, urethane pads are utilized using hyperelastic material model in the simulation. Formability in view of surface defect such as onset of dimple is compared with regard to various punch sizes. Consequently, it is confirmed that the flexible forming process for sheet material has appropriate capability and feasibility for manufacturing of smoothly curved surface instead of conventional die forming process.

• 한국축산시설환경학회지
• /
• 제19권1호
• /
• pp.33-38
• /
• 2013

We conducted investigations of the information and welfare of broiler chickens in Korea. The livestock housing of all broiler chicken farms were windowless type, bell feeder and nipple waterer were used, and stocking density was relatively higher (ranging from 18.2 $birds/m^2$ to 24.2 $birds/m^2$) than RSPCA's welfare standards for chicken hens (less than 19 $birds/m^2$). The ratios of sandwich panel, urethane form, slate, and steel plate in roofing materials were 61%, 21%, 13%, and 5%, respectively. The ratios of sandwich panel, urethane form, brick, and steel plate in wall materials were 61%, 21%, 13%, and 5%, respectively. The ratios of soil and concrete in flooring materials were 10% and 90%. The mist spray, fan, and cooling pad in cooling facilities were 42%, 32%, and 26%, respectively. Thus we believe that present data contribute to develop the animal welfare certification for broiler chickens and to improve animal welfare in Korea.

• 공업화학
• /
• 제28권1호
• /
• pp.57-63
• /
• 2017

본 연구에서는 다양한 NCO index에서 물 함량 변화가 자동차용 폴리우레탄 시트 폼 패드의 정적 안락감에 미치는 영향을 알아보았다. 정적 안락감에 영향을 미치는 요인을 파악하기 위해 UTM을 사용한 정하중 특성 시험을 통하여 히스테리시스 곡선을 나타냈으며, 이를 통해 25% 변형 시 경도와 65% 변형 시 경도, hysteresis loop area, hysteresis loss (%), 그리고 Sag factor를 구하였다. 동일한 NCO index에서 물 함량이 증가함에 따라 우레아 결합의 증가로 경도가 증가하고, 가교밀도가 증가하는 경향을 swelling ratio 측정으로 확인하였으며, 이에 따라 복원력은 감소하는 경향을 확인하였다. 또한 표면 경도의 증가로 인해 Sag factor가 감소하는 경향을 확인하였다. 동일한 물 함량에서 NCO index가 증가함에 따라 우레탄과 우레아 결합이 이소시아네이트와 추가 반응하여 가교도와 경도가 증가하고 이에 따라 복원력이 감소함을 확인하였다.

• 한국결정성장학회지
• /
• 제11권5호
• /
• pp.218-223
• /
• 2001

수평 Bridgman 방법으로 성장한 사파이어 인고트를 절단 연마한 후, 사파이어 결정기판의 표면을 우레탄 천 위에서 실리카 졸을 사용하여 폴리싱하였다. 표면의 결정성을 X-선 회절을 통하여 조사하였으며, 2중 결정회절에 의한 반치폭은 200~400 arcsec을 가지며, 결정 인고트의 절편화 또는 양면 연삭 연마에 따른 잔류응력에 의한 표면에서의 기계적인 스트레스에 의해 결정성이 손상되어진다. 화학-기계적인 폴리싱공정을 수행한 수에 표면처리로 $1,200^{\circ}C$로 4시간 열처리 및 산처리를 연속적으로 수행할 경우 결정성이 반치폭 8.3 arcsec까지 줄어들어 향상됨을 확인하였다.

• 대한기계학회논문집A
• /
• 제34권3호
• /
• pp.299-305
• /
• 2010

가변성형 공정에서 동일한 크기의 성형펀치 배열로 구성된 가변금형을 이용하는 경우 펀치의 크기가 일정하여 성형 가능한 곡률 반경이 제한되기 때문에 비교적 유연성이 낮다. 이에 본 연구에서는 가변금형의 유연성을 높이기 위하여 분할가변금형에 대한 개념을 제안하였다. 임의의 성형면을 형성하기 위하여 두 가지 크기의 펀치로 구성된 펀치 블록을 착안하였다. 상대적으로 큰 곡률 반경을 갖는 성형영역에 대해서는 크기가 큰 펀치 블록을 적용하였으며, 작은 곡률 반경을 갖는 성형영역에 대해서는 작은 크기의 펀치로 구성된 펀치 블록을 적용하였다. 해석적 연구를 토대로 성형된 제품의 단면 형상을 비교하였으며 이로부터 서로 다른 크기의 펀치 블록을 조합하여 구성한 분할가변금형을 이용한 판재의 성형공정이 비교적 복잡한 곡률 반경 분포를 갖는 곡면 가공에 적합함을 확인하였다.