• Journal of the Korean Society of Clothing and Textiles
• /
• v.10 no.2
• /
• pp.59-67
• /
• 1986

To control the amounts of formaldehyde released from the cotton fabric finished with N-methylol compounds, glycerol was used as a formaldehyde-scavenging agent. It was observed the effects of catalysts and curing conditions when aftertreated with glycerol on melamine resin finished fabric. The effects of Different processes of glycerol treatment, and different resins, urea resin and melamine resin, were compared. The conclusions obtained from the results are as follows: 1) It was shown hatt the aftertreatment with glycerol (treated without catalyst) was more effective than treated with catalysts in controlling free formaldehyde. 2) The optimum curing temperature and curing time for the glycerol aftertreatment without adversely affecting the other properties of fabric was about $160^{\circ}C$, 3 min. 3) According to the increase of glycerol concentration in both aftertreatment and simultaneous treatment the amounts of free formaldehyde was reduced. The rate of decrease was manifest within the limits of $6\%$ in the case of simultaneous treatment with glycerol ana resins, and $3\%$ in the case of glycerol aftertreatment on resin finished fabrics. 4) Dry wrinkle recovery angle was decreased the increase of glycerol concentration. Melamine resin had a little adverse effect than urea resin, particulary glycerol aftertreatment. 5) The breaking strength was increased with the increase of glycerol concentration.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.5
• /
• pp.672-681
• /
• 2015

As a part of abating the formaldehyde emission of amino resin-bonded wood-based composite panels, this study was conducted to investigate hydrolytic stability of urea-melamine-formaldehyde (UMF) resin depending on various hydrolysis conditions and hardener types. Commercial UMF resin was cured and ground into a powdered form, and then hydrolyzed with hydrochloric acid. After the acid hydrolysis, the concentration of liberated formaldehyde in the hydrolyzed solution and mass loss of the cured UMF resins were determined to compare their hydrolytic stability. The hydrolysis of cured UMF resin increased with an increase in the acid concentration, time, and temperature and with a decrease in the smaller particle size. An optimum hydrolysis condition for the cured UMF resins was determined as $50^{\circ}C$, 90 minutes, 1.0 M hydrochloric acid and $250{\mu}m$ particle size. Hydrolysis of the UMF resin cured with different hardener types showed different degrees of the hydrolytic stability of cured UMF resins with a descending order of aluminum sulfate, ammonium chloride, and ammonium sulfate. The hydrolytic stability also decreased as the addition level of ammonium chloride increased. These results indicated that hardener types and level also had an impact on the hydrolytic stability of cured UMF resins.

• Korean Journal of Soil Science and Fertilizer
• /
• v.24 no.1
• /
• pp.50-54
• /
• 1991

This study was conducted to evaluate the effect of five newly developed slow-release compound fertilizer varying urea/formaldehyde mole ratios on chinese cabbage against the checked plot of straight fertilizer. The chinese cabbage was obtained the highest yield in the product V which was 1.0 mole ratio of urea/formaldehyde adding with 6.7% urea resin, however, it was lowest in the product VII which the lowest mole ratio of urea/formaldehyde and the highest amount of the resin added. The appropriate product with one basal application for chinese cabbage should be one with 76.1 % of T-N dissolution in water after 24hrs and 71.7 % of T-N dissolution in soil 100 days after treatment. The total nitrogen content of the harvest plant in the product plot was lower compared to the checked plot of N P K and the available soil phosphrous after harvest was higher than that of the checked.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.1
• /
• pp.14-22
• /
• 2023

Economical use of larix (larch) boards (grade 3) in industries is lower than that of imported hardwood; thus, studies have been conducted toward performance improvement of larix boards. Herein, flexural modulus of larix board samples laminated with wood adhesives polyurethane resins, poly (vinyl acetate) resins, phenol-resorcinol-formaldehyde resins, melamine-formaldehyde resins, and urea-formaldehyde resins was compared with that of the samples bonded with adhesives reinforced with mesh-type basalt fibers. Moreover, the flexural moduli of the laminated samples bonded by mesh-type basalt fibers were compared with those of reinforced samples. The results showed that boards laminated with polyurethane and urea-formaldehyde resin adhesives had higher flexural modulus than those without the lamination. In particular, the increase in the flexural modulus was relatively significant for the 2- and 3-ply board structures laminated with polyurethane adhesives compared to those with reinforcement. The 3-ply board structure without reinforcement had the highest flexural modulus when the urea-formaldehyde resin adhesive was used.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.1
• /
• pp.3-8
• /
• 1988

This study was carried out to examine the effect of pretreatment of veneer with aluminum sulfate solution for the manufacture of the kapur plywood on the reduction of urea resin spread. The results were as follows: 1. Specific gravities of plywoods made of the kapur veneers ranged from 0.83 to 0.84 and their moisture contents based on air dry weight showed from 10.6% to 11.4%. These met the Korean Industrial Standards. 2. In the case of dry shear strength for the 3rd class plywood, 40% reduction- spread met K S as well as normal urea resin spread. pH of the aluminum sulfate solution gave better result at pH 4.5 and pH 6 than at pH 3. For the manufacture of the 2nd class plywood, hot and cold water-wet shear strength show the best results at the following conditions; such as 20% reduction spread, pH 4.5 of aluminum sulfate solution and all veneer treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.2
• /
• pp.221-228
• /
• 2019

This study reports the performance of urea-formaldehyde (UF) resins prepared at two different low formaldehyde/urea (F/U) mole ratios with different numbers of urea addition during synthesis. The second or third urea was added during the synthesis of UF resins to obtain two different low molar ratios of 0.7 and 1.0, respectively. The molecular weights, cure kinetics, and adhesion performance of these resins were characterized by the gel permeation chromatography, differential scanning calorimetry, and tensile shear strength of plywood, respectively. When the number of urea additions and F/U molar ratio increased, the gelation time decreased, whereas the viscosity and molecular weight increased. Further, the UF resins prepared with the second urea and 1.0 molar ratio resulted in greater activation energy than those with third urea and 0.7 molar ratio. Tensile shear strength and formaldehyde emission (FE) of the plywood that bonded with these resins increased when the number of urea additions and molar ratio increased. These results suggest that the UF resins prepared with 0.7 molar ratio and third urea addition provide lower adhesion performance and FE than those resins with 1.0 mole ratio and the second urea addition.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.3
• /
• pp.17-21
• /
• 1988

In order to investigate the extending effects on urea-formaldehyde resin- or phenol- formal- dehyde resin- glued keruing plywood, hot pressing temperatures were controlled to 110, 140, 170 and $200^{\circ}C$. As the extender, wheat flour, persimmon bark powder, chestnut bark powder, the equivalently- extended with the above three powders, and diatomite powder were respectively mixed with 5, 10, 15 and 20% ratios to the resin liquid, and also with these the no- extended was allowed. Based on the measured bonding strength, the conclusions were drawn: 1. In the urea- formaldehyde resin, extending effects on the bonding strength were in the order of wheat flour, the equivalently- extended with the wheat flour, persimmon- and chestnut bark powder, persimmon bark powder, chestnut bark powder. In the phenol- formaldehyde resin, the effects in the order of wheat flour, persimmon bark powder, diatomite powder, chestnut bark powder were resulted in. Specifically, superior bonding strength to the no-extended were given with the wheat flour and persimmon bark powder. 2. On the whole, the bonding strength decreased gradually, as the hot pressing temperature increased except for the diatomite powder extending.

• Journal of Sericultural and Entomological Science
• /
• v.27 no.2
• /
• pp.47-53
• /
• 1985

The studies on the reaction of Urea-Formaldehyde(UF) resin with silk fabric were studied, and the final results summarized as below; 1. The pH and UF molar ratio for preparing liquid resin was found at pH 4-5 and UF molar ration 1:2 and above. 2. The weight gains were increased with respect to increase in concentration of UF resin solution, while moisture regains were decreased. 3. The weight gains were significant high in case of wet pick up 70%. 4. The weight gains were increased with respect to increase in curing temperature and the amount of catalyst((NH4)2SO4) found was 2.5% on the weight of Dimethylol urea and Hydrochloric acid was 1%, Tartaric acid was 10%. 5. The effect of different catalyst on wash fastness of UF resin was good where as in case of acidic catalyst was significantly high. 6. The weight gains with different catalyst was high where as in case of potential acid catalyst was significantly high. 7. The crease recovery are increased with the increase of the weight gain of silk fabric and also stiffness are increased.

• Journal of Korean Society of Forest Science
• /
• v.94 no.6
• /
• pp.476-480
• /
• 2005

Agricultural straws such as rice and barley were used as partial replacement of raw materials for particleboard (PB) manufacture. A melamine-urea-formaldehyde (MUF) resin, based on 5 percent melamine addition of the resin solids weight, was synthesized in the laboratory for the bonding of PB. PBs were made using two straw particles based on 10, 20, 30, 40% oven dry weight addition with MUF resin. PBs were tested for physical and mechanical properties, and water soak dimensional stability. The results indicated that as rice and barley straws addition level were increased, the properties of IB, MOR and dimensional stabilities such as thickness swell and water absorption were decreased. Overall, the agricultural straws can be used at 15% substitution of raw materials for PB manufacture.

• Journal of the Korea Furniture Society
• /
• v.18 no.1
• /
• pp.20-30
• /
• 2007

This experiment was carried out to investigate the effects of number and location of finger joints on the bending strength of glue-laminated lumbers. Urea resin adhesives were used in this experiment and the resin content was 70% for cold pressing. The lamina were edge-jointed and end-jointed. The specimen were composed of one or three layers. The obtained results are summarized as follows; The effects of finger joints on the decrease of bending strength of glue laminated woods were different according to the number and location of finger joints. The decrease of MOR was highest on the middle position of laminated woods. The effects of several arrangements of finger joints on the bending strength of glue laminated woods showed on Figure 7 and 8. The variance of thickness-laminating on the bending strength of glue laminated woods were larger than those of width-laminating.