• 한국식품영양학회지
• /
• 제34권1호
• /
• pp.132-136
• /
• 2021

The purpose of this study is to measure the levels of eluted and dissolved CO2, and CO, volatile organic substances and radiation composition of Cheongsong mineral water which were collected from November 2019 to July 2020 during the autumn, spring, and summer seasons at collection points located in the upper, middle and lower spring waters. Data of the upper, middle and lower spring waters include the following: the amount of eluted water (average value±standard deviation, mL/min) was 30.07±0.52, 15.03±0.16, 23.73±0.42, and the amount of CO2 gas was 1,000 ppm or more. In addition, there was no detection of CO or total volatile organic substances (TVOC) and the radiation dose was 0.08 to 0.13. μSv/h. A blank test value of 0.08 to 0.10 μSv/h, when compared with the median value, showed a high value of 0.02 μSv/h, and the uranium test results provided by the Cheongsong-gun Office were 0.0118 mg/L (date 2019.06.18) and 0.0091 mg/L (date 2020.06.04.) respectively, which was less than the permission limit of 0.03 mg/L. However, it is believed that further research using more precise devices is needed in order to guarantee the safety and health of the water.

• Nuclear Engineering and Technology
• /
• 제54권2호
• /
• pp.653-660
• /
• 2022

The interaction between UN and CdCl₂ in the LiCl-KCl molten eutectic was studied at 1023 K. The chlorination was monitored by sampling and recording the redox potential of the medium. At 1023 K the chlorination of UN with cadmium chloride in the molten LiCl-KCl eutectic proceeds completely and results in the formation of uranium chlorides. The melts of the LiCl-KCl-UCl₃ or LiCl-KCl-UCl₄ compositions can be obtained by the end of experiment depending on the presence of metallic cadmium in the reaction zone. The higher the concentration of the chlorinating agent, the faster the reaction rate. At [CdCl₂]/[UN] = 1.65 (10% excess) the reaction proceeds to completion in about 7.5 h. At [CdCl₂]/[UN] = 7 the complete chlorination takes 2.5-3 h.

• Nuclear Engineering and Technology
• /
• 제54권9호
• /
• pp.3235-3241
• /
• 2022

The Korea Atomic Energy Research Institute (KAERI) is planning the construction of the KIJANG Research Reactor (KJRR) for stable supply of ⁹⁹Mo. The Fission ⁹⁹Mo Production Process (FMPP) of KJRR produces solid waste such as spent uranium cake and alumina cake, and liquid waste in the form of intermediate level liquid waste (ILLW) and low level liquid waste (LLLW). This study thus established the operating range and optimum operating conditions for the cementation of ILLW from FMPP. It also evaluated whether cement waste form samples produced under optimum operational conditions satisfy the waste acceptance criteria (WAC) of a disposal facility in Korea (Korea radioactive waste agency, KORAD). Considering economic feasibility and safety, optimum operational conditions were achieved at a w/c ratio of 0.55, and the corresponding salt content was 5.71 wt%. The cement waste form samples prepared under optimum operational conditions were found to satisfy KORAD's WAC when tested for structural stability and leachability. The results indicate that the proposed cementation conditions for the disposal of ILLW from FMMP can be effectively applied to KJRR's disposal facility.

• Nuclear Engineering and Technology
• /
• 제53권3호
• /
• pp.833-841
• /
• 2021

During the postulated severe accident of nuclear reactor, eutectic reaction leads to low-temperature melting of fuel cladding and early failure of core structure. In order to model eutectic melting with the moving particle semi-implicit (MPS) method, the eutectic reaction model is developed to simulate the eutectic reaction phenomenon. The coupling of mass diffusion and phase diagram is applied to calculate the eutectic reaction with the uniform temperature. A heat transfer formula is proposed based on the phase diagram to handle the heat release or absorption during the process of eutectic reaction, and it can combine with mass diffusion and phase diagram to describe the eutectic reaction with temperature variation. The heat transfer formula is verified by the one-dimensional melting simulations and the predicted interface position agrees well with the theoretical solution. In order to verify the eutectic reaction models, the eutectic reaction of uranium and iron in two semi-infinite domains is simulated, and the profile of solid thickness decrease over time follows the parabolic law. The modified MPS method is applied to calculate Transient Reactor Test Facility (TREAT) experiment, the penetration rate in the simulations are agreeable with the experiment results. In addition, a hypothetical case based on the TREAT experiment is also conducted to validate the eutectic reaction with temperature variation, the results present continuity with the simulations of TREAT experiment. Thus the improved method is proved to be capable of simulating the eutectic reaction in the severe accident.

• 방사성폐기물학회지
• /
• 제21권2호
• /
• pp.193-204
• /
• 2023

To ensure radiological safety margin in the transport and storage of spent nuclear fuel, it is crucial to perform source term and shielding analyses in advance from the perspective of conservation. When performing source term analysis on UO₂ fuel, which is mostly used in commercial nuclear power plants, uranium and oxygen are basically considered to be the initial materials of the new fuel. However, the presence of impurities in the fuel and structural materials of the fuel assembly may influence the source term and shielding analyses. The impurities could be radioactive materials or the stable materials that are activated by irradiation during reactor power operation. As measuring the impurity concentration levels in the fuel and structural materials can be challenging, publicly available information on impurity concentration levels is used as a reference in this evaluation. To assess the effect of impurities, the results of the source term and shielding analyses were compared depending on whether the assumed impurity concentration is considered. For the shielding analysis, generic cask design data developed by KEPCO-E&C was utilized.

• Nuclear Engineering and Technology
• /
• 제55권9호
• /
• pp.3464-3471
• /
• 2023

The Uranium/Molybdenum metallic fuel has been proposed as promising advanced fuel concept especially in the dispersed fuel geometry. The fuel is manufactured in the form of small fuel droplets (particles) placed in a fuel pin covered by a matrix. In addition to fuel particles, the pin contains voids necessary to compensate material swelling and release of fission gases from the fuel particles. When investigating this advanced fuel design, two important questions were raised. Can the dispersed fuel performance be analyzed using homogenization without significant inaccuracy and what size of fuel drops should be used for the fuel design to achieve optimal utilization? To answer, 2D burnup calculations of fuel assemblies with different fuel particle sizes were performed. The analysis was supported by an additional 3D fuel pin calculation with the dispersed fuel particle size variations. The results show a significant difference in the multiplication factor between the homogenized calculation and the detailed calculation with precise fuel particle geometry. The recommended fuel particle size depends on the final burnup to be achieved. As shown in the results, for lower burnup levels, larger fuel drops offer better multiplication factor. However, when higher burnup levels are required, then smaller fuel drops perform better.

• Nuclear Engineering and Technology
• /
• 제30권2호
• /
• pp.99-111
• /
• 1998

Chemical composition of the insoluble residue in a simulated spent PWR fuel(SIMRJEL) were studied. SIMFUELS were prepared by adding calculated amount of FP(fission product) elements with a burnup of 3.6% FIMA(fission per initial metal atom) to uranium in nitrate solution, evaporating the mixed solution to dryness, calcining at 90$0^{\circ}C$ in a stream of 4% H$_2$ + 96% He, and heating the pellet at 140$0^{\circ}C$ under high and low oxygen potentials. Insoluble residue was obtained from the dissolution of the SIMFUEL with HNO$_3$(1 : 1). The chemical composition of the SIMFUELs and the insoluble residues was determined by EPMA(electron probe microanalysis), XPS(X-ray photoelectron spectroscopy) and by XRD (X-ray diffraction) measurements. All of the insoluble residues suspended and precipitated were composed mainly of Mo, Ru with a small amount of Zr, Rh, Pd and Cd. The amount of insoluble residue(<1 wt.%) and a Mo/Ru ratio decreased with increasing oxygen potential. Formation of the zirconium molybdate precipitate, ZrMo$_2$O$_{7}$(OH)$_2$($H_2O$)$_2$, was observed in the residues. The possible role of Mo on the phase formation was discussed in regard to oxygen potential.l.

• Nuclear Engineering and Technology
• /
• 제54권11호
• /
• pp.4296-4309
• /
• 2022

Mesh and turbulence model sensitivity analyses have been performed on computational fluid dynamics simulations executed with Hydra and ANSYS Fluent for a single CANadian Deuterium Uranium (CANDU) 37M nuclear fuel bundle placed within a standard pressure tube. The goal of this work was to perform a methodical analysis to objectively determine an appropriate mesh and to gauge the sensitivity of different turbulence models for CANDU subchannel flow under isothermal conditions. The boundary conditions and material properties are representative of normal operating conditions in a high-powered channel of the Darlington Nuclear Generating Station. Four meshes were generated with ANSYS Workbench Meshing, ranging from 22 to 84 million cells, and analyzed here to determine an appropriate level of mesh resolution and quality. Five turbulence models were compared in the turbulence model sensitivity analysis: standard k - ε, RNG k - ε, realizable k - ε, SST k - ω, and the Reynolds Stress Model. The intent of this work was to gain confidence in mesh generation and turbulence model selection of a single bundle to inform the decision making of subsequent investigations of an entire fuel channel containing a string of twelve bundles.

• Nuclear Engineering and Technology
• /
• 제55권1호
• /
• pp.378-390
• /
• 2023

The SPES (Selective Production of Exotic Species) facility, currently under development at Legnaro National Laboratories of INFN, aims at the production of intense RIB (Radioactive Ion Beams) employing the Isotope Separation On-Line (ISOL) technique for interdisciplinary research. The radioactive isotopes of interest are produced by the interaction of a multi-foil uranium carbide target with a 40 MeV 200 μA proton beam generated by a cyclotron proton driver. The Target Ion Source (TIS) is the core of the SPES project, here the radioactive nuclei, mainly neutron-rich isotopes, are stopped, extracted, ionized, separated, accelerated and delivered to specific experimental areas. Due to efficiency reasons, the TIS unit needs to be replaced periodically during operation. In this highly radioactive environment, the employment of autonomous systems allows the manipulation, transport, and storage of the TIS unit without the need for human intervention. A dedicated remote handling infrastructure is therefore under development to fulfill the functional and safety requirement of the project. This contribution describes the layout of the SPES target area, where all the remote handling systems operate to grant the smooth operation of the facility avoiding personnel exposure to a high dose rate or contamination issues.

• Nuclear Engineering and Technology
• /
• 제55권1호
• /
• pp.156-168
• /
• 2023

This study investigates the high temperature oxidation behaviour of a Ni-20Cr-1.2Si (wt.%) alloy in steam from 1200 ℃ to 1350 ℃ by Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM), Energy Dispersive X-ray Spectroscopy (EDS) and X-ray Diffraction (XRD). The results demonstrate that exposed Ni-based alloy developed a thin oxide scale, consisted mainly of Cr₂O₃. The oxidation kinetics obtained from the experimental results was applied to evaluate the hydrogen generation considering a simplified reactor core model with different cladding alloys following an unmitigated Loss-Of-Coolant Accident (LOCA) scenario in a hypothetical Small Modular Reactor (SMR). Overall, experimental data and simulations results show that both Fe-based and Ni-based alloys may enhance cladding survivability, delaying its melting, as well as reducing hydrogen generation under accident conditions compared to Zr-based alloys. However, a substantial neutron absorption occurs when Ni-based alloys are used as cladding for current uranium-dioxide fuel systems, even when compared to Fe-based alloys.