• Wind and Structures
• /
• v.30 no.6
• /
• pp.633-648
• /
• 2020

The objective of this work was to investigate the interference effects of two-parallel bridge decks on aerodynamic coefficients, vortex-induced vibration, flutter instability and flutter derivatives. The two bridges have significant difference in cross-sections, dynamic properties, and flutter speeds of each isolate bridge. The aerodynamic static tests and aeroelastic tests were performed in TU-AIT boundary layer wind tunnel in Thammasat University (Thailand) with sectional models in a 1:90 scale. Three configuration cases, including the new bridge stand-alone (case 1), the upstream new bridge and downstream existing bridge (case 2), and the downstream new bridge and the upstream existing bridge (case 3), were selected in this study. The covariance-driven stochastic subspace identification technique (SSI-COV) was applied to identify aerodynamic parameters (i.e., natural frequency, structural damping and state space matrix) of the decks. The results showed that, interference effects of two bridges decks on aerodynamic coefficients result in the slightly reduction of the drag coefficient of case 2 and 3 when compared with case 1. The two parallel configurations of the bridge result in vortex-induced vibrations (VIV) and significantly lower the flutter speed compared with the new bridge alone. The huge torsional motion from upstream new bridge (case 2) generated turbulent wakes flow and resulted in vertical aerodynamic damping H1^* of existing bridge becomes zero at wind speed of 72.01 m/s. In this case, the downstream existing bridge was subjected to galloping oscillation induced by the turbulent wake of upstream new bridge. The new bridge also results in significant reduction of the flutter speed of existing bridge from the 128.29 m/s flutter speed of the isolated existing bridge to the 75.35 m/s flutter speed of downstream existing bridge.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.9A
• /
• pp.1422-1430
• /
• 2000

S(Synchronous)-CDMA is a new cable modem technology applicable to the upstream channel for high speed multimedia communication using CATV networks. In this paper we analyze the transmitting and receiving process of S-CDMA scheme based on Terayon patent and derive bit error probability of S-CDMA and TDMA scheme in the $\varepsilon$-mixture impulse noise model which appropriately reflects impulse noise characteristics of upstream channel by using various parameters. This analysis results are a good match with the simulation results. We also compare Eb/No gain performance of S-CDMA with TDMA in 16, 32, 64, QAM.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.8 no.4
• /
• pp.170-181
• /
• 2009

When a slow-moving vehicle occupies one of the lanes of a multi-lane highway, it often causes queuing behind, unlike one is caused by an actual stoppage on that lane. This happens when the traffic flow rate upstream from the slow vehicle exceeds a certain critical value. This phenomena is called as the Moving Bottleneck, defined by Gazis and Herman (1992), Newell (1998) [3], and Munoz and Daganzo (2002), who conducted the flow estimates of upstream and downstream and considered slow-moving vehicle speed and the flow ratio exceeding slow vehicle and the microscopic traffic flow characteristics of moving bottleneck. But, a study of delay on moving bottleneck was not conducted until now. So this study provides a average delay time model related to upstream flow and the speed of slow vehicle. We have chosen the two-lane highway and homogeneous traffic flow. A slow-moving vehicle occupies one of the two lanes. Average delay time value is a result of AIMSUN[9], the microscopic traffic flow simulator. We developed a multiple regression model based on that value. Average delay time has a high value when the speed of slow vehicle is decreased and traffic flow is increased. Conclusively, the model is formulated by the negative exponential function.

• Journal of Korean Port Research
• /
• v.14 no.4
• /
• pp.419-427
• /
• 2000

Today travel demand continues to increase with spread of economic zones. Also, urban freeway plays an important role in intra-zone transportations as a major corridor in a big city. However, most of urban freeways experience a severe congestion with the excess of inflowing or outflowing traffic through freeway ramps. The purpose of this study is to identify the traffic characteristics, analyze the relationships between the traffic characteristics and finally construct the speed predictive models on the ramp junctions of urban freeway under the intelligent transportation system(ITS) settings. From the analyses of traffic characteristics following results were obtained: ⅰ) 24 hours average traffic characteristics flow, occupancy, speed under the ITS settings showed about 40%, 38%, 8.8% increase each on urban freeway junctions period when compared with that under the non-ITS settings each other. Free flow speed and traffic flow on the mainline sections of urban freeway under the ITS settings also showed about 20% and 17% increase when compared with that under the non-ITS, respectively. ⅱ) The upstream when compared speed( $S_{u}$)and downstream occupancy( $O_{d}$) were especially shown to have higher explanatory powers on the stable flow ramp junctions, but the upstream speed( $S_{u}$) and downstream flow( $V_{d}$) were especially shown on the unstable flow ramp junctions of urban freeway under the ITS settings.ngs.ngs.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.278-281
• /
• 2008

This study demonstrates the advantages of a shear-free structure designed to modify vertical profiles of wind speed in the atmospheric surface layer. Computational fluid dynamics(CFD) software, FLUENT is used to interpret the velocity field modification around the structure and wind turbine. The shapes of shear-free structure, installed at upstream toward prevailing wind direction, would be fences, buildings and trees, etc. According to the simulation results, it is obvious that wind shear between heights of wind turbine's blades is decreased together with a speed-up advantage. This would lead decrease of periodic wind loading caused by wind shear and power-out increase by flow uniformity and wind speed-up.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.14 no.3
• /
• pp.157-168
• /
• 2011

In order to promote efficiency of upstream and downstream migration of fishes, this study has developed a combined fishway of herring-bone bottom baffle type and brush type fishways. The results obtained are as follows : 1. In a channel with constant incline, the velocity of current generally shows a distinct tendency of acceleration as it goes down the stream. But in the hydraulic experiment of herring-bone bottom baffle type fishway, the velocity reached its maximum only at 0.4m/sec, and it tended to be stable without any acceleration. 2. The velocity in the brush type fishway showed a distinct tendency of acceleration as the discharge increased. But its greatest velocity was only 0.3m/sec, and its velocity change according to the discharge increase was only 0.15m/sec at maximum. 3. The maximum velocity in the combined type fishway was less than half of the blast speed of the poorest swimmer, the juvenile eel with 90mm of body length. So any species of fishes are supposed to be able to migrate upstream from the estuary through this combined type fishway. 4. The field experiment of upstream migration showed that the combined type fishway can promote efficiency of upstream and downstream migration of any species of fishes.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.591-596
• /
• 2000

Flow through compliant tubes with linear taper in wall thickness is numerically simulated by finite element analysis. Two models are examined: a planar two-dimensional channel, and an axisymmetric tube. For verification of the numerical method, flow through a compliant stenotic vessel is simulated and compared to existing experimental data. Computational results for an axisymmetric tube show that as cross-sectional area falls with a reduction in downstream pressure, flow rate increases and reaches a maximum when the speed index (mean velocity divided by wave speed) is near unity at the point of minimum cross-section area, indicative of wave speed flow limitation or "choking" (flow speed equals wave speed) in previous one-dimensional studies. For further reductions in downstream pressure, flow rate decreases. Cross-sectional narrowing is significant but localized. When the ratio of downstream-to-upstream wall thickness is ${\le}$ 2 the area throat is located near the downstream end; as wall taper is increased to ${\ge}$ 3 the constriction moves to the upstream end of the tube. In the planar two-dimensional channel, area reduction and flow limitation are also observed when outlet pressure is decreased. In contrast to the axisymmetric case, however, the elastic wall in the two-dimensional channel forms a smooth concave surface with the area throat located near the mid-point of the elastic wall. Though flow rate reaches a maximum and then falls, the flow does not appear to be choked.

• Journal of Korean Port Research
• /
• v.13 no.1
• /
• pp.113-122
• /
• 1999

Congestion and traffic accidents occur on the merge and diverge sections in the interchange of the freeway. Studies have been conducted to reduce the traffic delay and accidents on the merge section in the freeway since 1960s. but a study was not conducted to estimate the speed variation on the merge section construct models estimated for the speed variation and suggest the appropriate measures. The purpose of this study was to identify the traffic flow characteristics on the merge section in the freeway construct the models estimated for the speed variation on the merge section in the freeway and finally establish the appropriate measure for reduction of traffic delay and accidents on the merge section in the freeway. The following results were obtained: I) Speed variations in the urban freeway appeared to be about 3.2mph, 6.5mph and 7.4mph based on the morning peak period, afternoon peak period and 24-hours period but those in the suburban freeway appeared to be about 8.0mph, 11.1mph and 10.1mph based on the same periods respectively. So different speed reduction signs need be installed to reduce delay and accidents on the merge section in the freeway based on the areas and periods as the freeway traffic management system(FTMS). ii) These models estimated for speed variation need to be studied with the changeable message sign(CMS) technique based on the real-time data so that the traffic flow could be maximized and the traffic delay and accidents be on the merge section in the freeway as more efficient freeway traffic management system(FTMS) in the near future.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4D
• /
• pp.443-450
• /
• 2009

Uninterrupted facility - since there is a close relationship between traffic volume, speed and density -, when a ramp traffic flow merges into the main line, will change the traffic speed or density, and the corresponding correlational model equation will be changed. Thus, this study, using time and space-series traffic data on areas under the influence of such a merging, identified sections which changed the correlation between speed and density variables, and examined such changes. As a result, the upstream and merging sections showed the "Underwood"-shaped exponent, and the downstream after passing the merging section showed a straight line "Greenshields" model. The downstream section which changed the correlation between speed and density showed a gradual downstream movement phenomenon within 100 m-500 m from the end of the third lane linking with the ramp, as the traffic approached the inner lanes. Also, the upstream section, merging section, and downstream section involving a change showed heterogeneous traffic flows which, in the speed-density model, have a statistically different free flow speed (constant) and a different ratio of free flow speed to jam density (gradient).

• 한국연소학회:학술대회논문집
• /
• 2003.05a
• /
• pp.103-108
• /
• 2003

The control of flame shapes in a laminar pre-mixed flame has been experimentally investigated for propane/air pre-mixed laminar flames. Flames of different size and shapes are observed with heated wires or by controlling the equivalence ratio and flow rate of a mixture. The characteristics of the partitioning of a flame or the merge of flames are analyzed and explained by considering the balance between laminar flame speed and upstream mixture velocity. A combustor might be sized down while maintaining its heat production rate the same by partitioning a flame established in it. When the equivalence ratio of mixture is decreased, individual flames are merged together and the upstream mixture velocity can be practically decreased on a nozzle having opening ratio less than unity. As a result, the flame shape is to he adjusted until the newly established balanced condition is satisfied, and then. the stable combustion can be achieved again.