• Structural Engineering and Mechanics
• /
• 제44권6호
• /
• pp.775-799
• /
• 2012

This work approaches the structural performance of masonry arches that have a small ratio between number of vossoirs and span length. The aim of this research is to compare and validate three different methods of analysis (funicular limit analysis F.L.A., kinematic limit analysis K.L.A. and plane stress Finite Element Analysis F.E.A.) with an experimental campaign. 18 failure tests with arches of different shapes and boundary conditions have been performed. The basic failure mechanism was the formation of enough hinges in the geometry. Nevertheless, in few cases, sliding between vossoirs also played a relevant influence. Moreover, few arches didn't reach the collapse. The FLA and KLA didn't find a solution close to the experimental values for some of the tests. The low number of vossoirs and joints become a drawback for an agreement between kinematic mechanism, equilibrium of forces and geometry constraints. FLA finds a lower bound whereas KLA finds an upper bound of the ultimate load of the arch. FEA is the most reliable and robust method and it can reproduce most of the mechanism and ultimate loads. However, special care is required in the definition of boundary conditions for FEA analysis. Scientific justification of the more suitability of numerical methods in front of classic methods at calculating arches with a few vossoirs is the main original contribution of the paper.

• Restorative Dentistry and Endodontics
• /
• 제17권2호
• /
• pp.365-382
• /
• 1992

The purpose of this study was to evaluate the adaptation of filling material to the dentinal walls of root canals with and without smear layer. Fifty extracted upper and lower anterior teeth were selected, and the root canals were instrumented with K - files 1mm short of the apical foramen by step - back method. The teeth were randomly divided into two groups of 25 each : in the group I, smear layers were not removed, and in the group II, smear layers were removed by 15% EDTA solution. Again the two groups 25 teeth were randomly divided into unfilled contol group and filling groups(lateral, ultrasonic, ULTRAFIL, McSpadden compaction group). Upon completion of root canal filling, the teeth were grooved on the both the labial and lingual surfaces and then split with mallet and chisel. Each specimens were examined with JSM - 840 Scanning Electron Microscope (JEOL., Japan). The results were as follows : 1. In the contol group, dentinal tubules of group I couldn't be distinguished in the canal wall, but those of group II appeared to be open and patent. 2. In the filling groups of group I, the tubular penetration of the sealer or gutta percha couldn't be seen, but in the filling groups of group II, it could be seen except McSpadden compaction group. 3. In the filling groups, ULTRAFIL group showed the best adaptation of filling material to root canal wall among the group I, and lateral and ultrasonic condensation group showed the best adaptation of filling material among the group II. McSpadden compaction group showed the worst adaptation in group I, II. 4. Generally, the group II showed better adapation of filling material to root canal wall than the group I.

• 한국태양에너지학회 논문집
• /
• 제29권5호
• /
• pp.45-52
• /
• 2009

Fossil power plants firing lower grade coals or equipped with modified system for $NO_x$ controls are challenged with maintaining good combustion conditions while maximizing generation and minimizing emissions. In many cases significant derate, availability losses and increase in unburned carbon levels can be attributed to poor combustion conditions as a result of poorly controlled local fuel and air distribution within the boiler furnace. In order to develop a on-line combustion tuning system, field test was conducted at operating power boiler. During the field test the exhaust gases' $O_2,\;NO_x$ and CO was monitored by using a spatially distributed monitoring grid located in the boiler's high temperature vestibule and upper convective rear pass region. At these locations, the flue gas flow is still significantly stratified, and air in-leakage is minimal which enables tracing of poor combustion zones to specific burners and over-fire air ports. using these monitored information we can improving combustion at every point within the furnace, therefore the boiler can operate at reduced excess $O_2$ and gas temperature deviation, reduced furnace exit gas temperature levels while also reducing localized hot spots, corrosive gas conditions, slag or clinker formation and UBC. Benefits include improving efficiency, reducing $NO_x$ emissions, increasing output and maximizing availability. Discussion concerning the reduction of greenhouse gases is prevalent in the world. When taking a practical approach to addressing this problem, the best way and short-term solution to reduce greenhouse gases on coal-fired power plants is to improve efficiency. From this point of view the real time optimized combustion tuning approach is the most effective and implemented with minimal cost.

• 대한수의학회지
• /
• 제36권2호
• /
• pp.379-387
• /
• 1996

The objects of the present study were to establish the method of purification, subunit dissociation of verotoxin-2 (VT2) produced by Escherichia coli O157:H7, and to investigate the characteristics of purified verotoxin-2 such as molecular weight and composition of amino acid. The results were summerized as follows; Verotoxin-2 was extracted by addition of polymyxin B sulfate into bacterial cell lysate prepared from Escherichia coli O157:H7(KSC109). As an initial step, the bacterial cell lysate was precipitated with 30% saturated ammonium sulfate. The precipitated crude toxin was then subjected to anion-exchange, chromatofocusing and cation-exchange chromatography. Using this scheme, we obtained highly purified toxin with a specific activity of $1.1{\times}10^9$ $CD_{50}/mg$. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis(SDS-PAGE) for purified VT2 showed two protein bands. The upper band, approximately 32 Kd, was supposed as A subunit and the lower band, approximately 7.7 Kd, was supposed as B subunit. When the toxin was separated in the subunit-dissociating solution, two peaks emerged with retention times of 15 and 28 min by HPLC. These peaks represented A subunit and B subunit, respectively. The amino acid composition of purified VT2 were made up in order of glutamic acid, histamine, asparaginic acid, histidine, lysine, alanine and leucine etc. The largest amount among the amino acid composing VT2 was methionine.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2004년도 춘계 학술대회논문집
• /
• pp.146-153
• /
• 2004

The Numerical study has been carried out to investigate the effects of chemical reaction and thermal radiation on the rocket plume flow-field at various altitudes. The theoretical formulation is based on the Navier-Stokes equations for compressible flows along with the infinitely fast chemistry and thermal radiation. The governing equations were solved by a finite volume fully-implicit TVD(Total Variation Diminishing) code which uses Roe's approximate Riemann solver and MUSCL(Monotone Upstream-centered Schemes for Conservation Laws) scheme. LU-SGS (Lower Upper Symmetric Gauss Seidel) method is used for the implicit solution strategy. An equilibrium chemistry module for hydrocarbon mixture with detailed thermo-chemical properties and a thermal radiation module for optically thin media were incorporated with the fluid dynamics code. In this study, kerosene-fueled rocket was assumed operating at O/F ratio of 2.34 with a nozzle expansion ratio of 6.14. Flight conditions considered were Mach number zero at ground level, Mach number 1.16 at altitude 5.06km and Mach number 2.9 at altitude 17.34km. Numerical results gave the understandings on the detailed plume structures at different altitude conditions. The diffusive effect of the thermal radiation on temperature field and the effect of chemical recombination during the expansion process could be also understood. By comparing the results from frozen flow and infinitely fast chemistry assumptions, the excess temperature of the exhaust gas resulting from the chemical recombination seems to be significant and cannot be neglected in the view point of performance, thermal protection and flow physics.

• International Journal of Quality Innovation
• /
• 제9권3호
• /
• pp.71-91
• /
• 2008

The definition of cycle time is the time from the wafer start to the wafer output. It usually takes one or two months to get the product since customer decides to produce it. The cycle time is a critical factor for customer satisfaction because it represents the response time to the market. Long cycle time reflects the ineffective investment for the capital. The cycle time is very important for foundry because long cycle time will cause customer unsatisfied and the order loss. Consequently, all of the foundries put lots of human source in the cycle time improvement. Usually, we make decisions based on the experience in the cycle time management. We have no mechanism or theory for cycle time management. We do work-in-process (WIP) management based on turn rate and standard WIP (STD WIP) set by experiences. But the experience didn't mean the optimal solution, when the situation changed, the cycle time or the standard WIP will also be changed. The experience will not always be applicable. If we only have the experience and no mechanism, management will not be work out. After interview several foundry fab managers, all of the fab can't reflect the situation. That is, all of them will have an impact period after product mix or utilization varied. In this study, we want to develop a formula for standard WIP and use statistical process control (SPC) concept to set WIP upper/lower limit level. When WIP exceed the limit level, it will trigger action plans to compensate WIP Profile. If WIP Profile balances, we don't need too much WIP. So WIP level could be reduced and cycle time also could be reduced.

• Current Optics and Photonics
• /
• 제1권4호
• /
• pp.389-395
• /
• 2017

This paper investigates a method to improve the lighting performance of white light-emitting diodes (WLEDs), which are packaged using two separate remote phosphor layers, a yellow-emitting YAG:Ce phosphor layer and a red-emitting ${\alpha}-SrO{\cdot}3B_2O_3:Sm^{2+}$ phosphor layer. The thicknesses of these two layers are $800{\mu}m$ and $200{\mu}m$, respectively. Both of them are examined in conditions where the average correlated color temperatures (CCT) are 7700 K and 8500 K. For this two-layer model, the concentration of red phosphor is varied from 2% to 30% in the upper layer, while in the lower layer the yellow phosphor concentration is kept at 15%. It was found interestingly that the lighting properties such as color rendering index (CRI) and luminous flux are enhanced significantly, while the color uniformity is maintained in a relatively close range to the one of one-layer configuration (measured at the same correlated color temperature). Besides, the transmitted and reflected light of each phosphor layer are revised by combining Kubelka-Munk and Mie-Lorenz theories. Through analysis, it is demonstrated that the packaging configuration of two-layer remote phosphor that employs red-emitting ${\alpha}-SrO{\cdot}3B_2O_3:Sm^{2+}$ phosphor particles provides a practical solution for general WLEDs lighting.

• Journal of Korean Dental Science
• /
• 제9권1호
• /
• pp.1-8
• /
• 2016

Purpose: The aim of this study was to evaluate the rat periodontal ligament cell viability under $0^{\circ}C/2$ MPa condition up to one week using in vivo 3-(4,5-dimethylthiazol-2-y1)-2,5-diphenyltetrazolium bromide (MTT) assay. Materials and Methods: As soon as 110 upper molar teeth of rats were extracted, they were stored in Hartman's solution under $0^{\circ}C/2$ MPa condition for 1, 2, 3, 4, and 7 days each. All specimens were treated with in vivo MTT assay and the value of optical density was measured by ELISA reader. These values were statistically analyzed by one-way ANOVA. Result: There was no statistical difference on MTT value between immediate and 1 day storage group. There were statistically significant differences between 1 day and 2 days tsorage, 2 and 3 days storage groups, respectively. Teeth of 34, and 7 days storage groups showed significantly lower MTT valuesc ompared with shorter period storage groups. Conclusion: When the MTT values were substituted in standard curve, 1 day storage group at $0^{\circ}C/2$ MPa condition showed 68% cell viability when compared with immediate group. It dropped to 13% at 2 days, and to less than 5% at 3 days or more.

• 한국생산제조학회지
• /
• 제23권2호
• /
• pp.178-185
• /
• 2014

This paper describes a fabrication multiplexing sensor probe that employs a fiber Bragg grating(FBG) based on multiple measurements to determine the blade deflection of a wind power generator the reliability analysis of this probe is also presented. To diminish the temperature sensitivity of the FBG sensor, we form multiple CFRPs onto the upper and lower layers of the FBG and package it with an epoxy resin. As a result, the depth of the CFRP is 1mm, and the temperature sensitivity is $2.39pm/^{\circ}C$. We construct a sensor network utilizing the fabricated sensor with a blade beam model. As the number of pendulums is increased on the fore-end of the beam, the strain value is measured. The strain variation is calculated from the measurement of the load on the blade beam model by monitoring the strain of the FBG sensor. When the linear equation is applied, the strain error is 0.4% and when the finite difference method is used, the tip deflection error is 3.3%. The displacement error derived from the strain value of the FBG sensor is 4.39%. The calculated result between the measured value of the dead-end of the beam and the strain is less than 2.46% tip distortion error. Therefore, our proposed multiplexing sensor probe is a low-cost and high-reliability solution for a commercial wind power generator.

• 대한소아치과학회지
• /
• 제24권2호
• /
• pp.361-382
• /
• 1997

The effect of fluoride pretreatment upon root resorption after delayed replantation was studied in beagle dogs. Upper and lower incisors were extracted and bench dried for 45 minutes. 1% Stannous fluoride solution, 2% neutral sodium fluoride gel and 1.23% acidulated phosphate fluoride gel were used for the pre-treatment of replanted root surface in the experimental groups. Replantation was done with no treatment in control group. After of an experimental periods 3 weeks, animals were sacrificed by perfusion followed by sample preparation. A histomorphometric method was applied for evaluation of tissue reactions observed in each group under light microscope. Scanning electron microscopic observation was done to find out any different surface topography between groups. The results were as follows: 1. Fluoride-treated groups showed in general the better healing patterns than untreated control group. 2. Comparisons between three experimental groups revealed the general superiority of APF-treated group over the other groups in terms of tissue healing reaction by showing the highest frequency in uncomplicated healing pattern and surface resorption and the lowest in inflammatory resorption, but with no statistical significance(p>.05). 3. Scanning elecron micrographs showed the irregular distribution of resorption cavities and the attached bone of variable size and shape in all groups. 4. It can be concluded that the types of fluoride did not have significant impact on the early tissue reactions after delayed replantation under the condition of the present experiment.