• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.1
• /
• pp.32-42
• /
• 2015

In this paper, we considered the scenario that one cellular link and muti-D2D links share the same frequency resource which can improve the spectrum efficiency during uplink communication in LTE (Long Term Evolution)-Advanced network. In order to reduce the interference caused to the D2D users, we set DME (Discovery and Management Entity) which can send the area information to eNB(evolved Node B). We proposed a resource allocation scheme by using these assistant devices to reduce the interference that CUE (Cellular User Equipment) causes to DUE Rx (D2D UE Receiver). Basing on the area information, in order to mitigate the interference among the D2D pairs which share the same frequency resource, a power control scheme has been proposed. The simulation results prove that by using the DMEs, the proposed schemes improve the stability of D2D communication and bring the highest performance of the communication system when comparing to the other different schemes.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.4C
• /
• pp.241-253
• /
• 2011

In this paper, a CFNC (Complex Field Network Coding) scheme is presented, which focuses on improving transmission efficiency by reducing time slots that are needed to exchange data frames. Conventional CFNC scheme has the advantage of minimizing the number of time slots required for information exchanges. However, there exists serious performance deterioration because the transmit signals are interfered with each other. Moreover, when CFNC scheme is applied, the estimation and compensation performance of fine frequency offset severely deteriorates due to the multiple frequency offsets in received signal of relay node. In order to overcome these critical problems, we propose an improved CFNC scheme with modified maximum likelihood decision method which uses uplink transmit diversity. Also, we propose an enhanced fine frequency offset estimation method and a corresponding compensation method to deal with the multiple frequency offsets. Corresponding simulation results verify that the proposed methods are able to effectively solve the problems of CFNC scheme.

• Journal of Communications and Networks
• /
• v.10 no.4
• /
• pp.412-421
• /
• 2008

We observe simultaneous transmission of relay stations (RSs) allowed in current IEEE 802.16j draft standard for multi-hop relay networks may involve severe interference among the RSs, hence leading to throughput degradation. Allowing only 1/3 of the RSs to simultaneously transmit instead of 1/2 RSs as in the current draft standard reduces the interference but results in reduced throughput. To remedy this problem, we devise schemes to incorporate network coding at link-layer level (decode-and-forward) into the simultaneous transmission of RSs. Data movement is rearranged to maximize coding gain. Formula is derived to dictate exact movement of packets traveling between base station (BS) and mobile stations (MSs) via intermediate RSs. The frame structure in the current IEEE 802.16j draft standard does not allow broadcast needed for network coding. We devise a new frame structure which supports the broadcast. A new R-MAP (pointers to the burst data) is introduced to implement the broadcast. Since our new frame structure is used only for BS to RS or RS to RS communication, our schemes retain backward compatibility with legacy MSs based on IEEE 802.16e standard. Simulation based on simple configuration of RSs shows considerable improvement in terms of system throughput and round trip delay. For a 4-hop relay network with 1 BS and 4 RSs with symmetric traffic in uplink (UL) and downlink (DL), throughput is improved by 49% in DL and by 84% in UL traffic compared with IEEE 802.16j draft standard under the assumption that omni-directional antennae are used in BS and RSs.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.1
• /
• pp.43-48
• /
• 2021

One of the effective ways to increase data transmission rate is to use massive antenna technique where tens or hundreds of antennas are deployed in base station and spatial diversity gain is improved by multiuser method. If multiuser method is applied, there will be inter-user interference and maximal ratio combiner (MRC) is conventionally used to reduce the complexity of the receiver and to eliminate interference. However, as the number of mobile devices increases, the performance of the conventional receiver becomes deteriorated. To solve this problem, we propose a new detector that completely eliminates the interference from the registered devices and reduces that from the unregistered devices. Then, to reduce the complexity of the proposed scheme, we propose adaptive algorithm of the proposed scheme. Through simulation, we show that the proposed scheme has better bit error rate performance than the conventional scheme.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.3 s.118
• /
• pp.248-256
• /
• 2007

In this paper, we propose a selective DFT spreading method to solve a high PAPR problem in uplink OFDMA system. A selective characteristic is added to the DFT spreading, so the DFT spreading method is mixed with SLM method. However, to minimize increment of computational complexity, differently with common SLM method, our proposed method uses only one DFT spreading block. After DFT, several copy branches are generated by multiplying with each different matrix. This matrix is obtained by linear transforming the each phase rotation in front of DFT block. And it has very lower computational complexity than one DFT process. For simulation, we suppose that the 512 point IFFT is used, the number of effective sub-carrier is 300, the number of allowed sub-carrier to each user's is 1/4 and 1/3 and QPSK modulation is used. From the simulation result, when the number of copy branch is 4, our proposed method has more than about 5.2 dB PAPR reduction effect. It is about 1.8 dB better than common DFT spreading method and 0.95 dB better than common SLM which uses 32 copy branches. And also, when the number of copy branch is 2, it is better than SLM using 32 copy branches. From the comparison, the proposed method has 91.79 % lower complexity than SLM using 32 copy branches in similar PAPR reduction performance. So, we can find a very good performance of our proposed method. Also, we can expect the similar performance when all number of sub-carrier is allocated to one user like the OFDM.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.2
• /
• pp.106-106
• /
• 2014

SIGMA (Scientific cubesat with Instrument for Global Magnetic field and rAdiation)는 근 지구공간에서 우주방사선량 측정과 자기장 변화 검출의 과학적 목적과 교육적 목적을 가지고 개발하고 있는 초소형 큐브위성이다. $100mm{\times}100mm{\times}340.5mm$의 크기로 약 3.6 kg의 무게를 가지며, 탑재체는 방사선에 대하여 인체와 동일한 산란 흡수 특성을 가진 Tissue Equivalent Proportional Counter (TEPC)와 자기장 측정을 위한 Magnetometer (Mag)이다. 위성체는 구조계, 자세제어계, 전력계, 명령 및 데이터처리계, 통신계로 구성되어있다. 구조계는 위성의 뼈대인 Chassis와 Mag deployer로 이루어져있고, 위성의 안정적인 자세유지를 목적으로 Attitude Control System (ACS) Board와 Torque Coil이 자세제어계로 구성된다. 전력의 생산과 공급 및 충전은 태양전지판과 Electrical Power System (EPS), 리튬 배터리로 구성된 전력계에서 이뤄지며, 명령 및 데이터처리계는 On Board Computer (OBC)와 Instrument Interface board (IIB)를 중심으로 서브시스템의 명령체계와 데이터처리를 다룬다. 통신계는 Uplink인 VHF 안테나와 Downlink인 UHF, S-band 안테나로 구성되며 지상과 명령을 송수신한다. SIGMA는 타임인터럽트 기능을 활용한 Flight Software (FSW)로 운용되며 임무에 따른 6가지 모드의 시나리오로 위성을 운용한다. 이에 SIGMA의 개발과 테스트 결과를 소개한다. 본 큐브위성 개발기술을 바탕으로 향후 천문관측용 위성에도 활용할 예정이다.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.1
• /
• pp.39-47
• /
• 2005

The range of hardware implementation increases in communication systems as high-speed processing is required for high data rate. In the broadband wireless access (BWA) system based on IEEE standard 802.16 the functions of higher part in the MAC layer to Provide data needed for generating MAC PDU are implemented in software, and the tasks from formatting MAC PDUs by using those data to transmitting the messages in a modem are implemented in hardware. In this paper, the interface hardware for efficient message exchange between MAC and PHY layers in the BWA system is designed. The hardware performs the following functions including those of the transmission convergence(TC) sublayer; (1) formatting TC PDU(Protocol data unit) from/to MAC PDU, (2) Reed-solomon(RS) encoding/decoding, and (3) resolving DL MAP and UL MAP, so that it controls transmission slot and uplink and downlink traffic according to the modulation scheme of burst profile. Also, it provides various control signal for PHY modem. In addition, the truncated binary exponential backoff (TBEB) algorithm is implemented in a subscriber station to avoid collision on contention-based transmission of messages. The VLSI architecture performing all these functions is implemented and verified in VHDL.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.5 s.347
• /
• pp.94-103
• /
• 2006

Ethernet passive optical network (EPON) has drawn many attention as a promising access network technology for FTTH because it can provide a high bandwidth with a low cost. Since the uplink bandwidth in the EPON system is shared by many users, it is necessary for an EPON system to have an efficient bandwidth allocation mechanism. To support QoS in EPON, the previous bandwidth allocation schemes employ strict priority queueing (SPQ). Since SPQ gives unlimited priority to higher service class, the QoS of lower service classes gets worse. In this paper, we propose Class Gated DBA (Dynamic Bandwidth Allocation) algorithm in which the bandwidth is requested / granted in a service class basis. To avoid the monopoly in bandwidth usage by higher classes the maximum bandwidth that is allocate to each service class is limited (fairness between services classes). In addition, to avoid the monopoly in bandwidth usage by some particular users, each ONU runs fairness bandwidth allocation algorithm within each service classes. Through computer simulations, it is verified that the proposed algorithm achieves a good level of QoS, and at the same time maintains a good level of fairness between both service classes and users.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.10-21
• /
• 2015

Cellular Network assisted device-to-device (D2D) communication has been growing to reduce the overload of eNodeB and mitigate the frequency shortage. However, by sharing the uplink frequency resource with the cellular network, the interference between cellular and D2D is increased. In this paper, we propose the advanced receiver based on soft decision to reduce the interference between cellular and D2D. The proposed receiver can suppress and cancel the interference by calculating the unbiased estimation value of interference signal using minimum mean square error (MMSE) or interference rejection combing (IRC) receiver. The interference signal is updated using soft information expressed by log-likelihood ratio (LLR). We perform a system level simulation based on the 20-MHz bandwidth of the 3GPP LTE-A system. Simulation results show that the proposed receiver can improve SINR, throughput and spectral efficiency compared to conventional receivers.

• Journal of Navigation and Port Research
• /
• v.26 no.1
• /
• pp.22-27
• /
• 2002

The 25 Watt hybrid MIC SSPA has been developed in the frequency rang from 1.6265 GHz to 1.6465 GHz for uplink of INMARST's earth station. To simplify the fabrication process, the whole system is designed of two parts composed of a friving amplifier and a power amplifier. The Motorolas MRF-6401 is used for driving part, the Motorolas MRF-16006 and MRF-16030 is used the power amplifier. We reduced weight and volume of high power amplifier through arranging the bias circuits in the same housing. The realized SSPA has more than 30 dB for gain within 20 MHz bandwidth, and the voltage standing wave ratios(VSWR) of input and output port are less than 1.7, respectively. The output power of 44 dBm is achieved at the 1 dB gain compression point of 106365 GHz These results reveal a high power amplifier of 25 Watt which is the design target. The Proposed SSPA manufacture techniques in this paper can be applied to the implementation of high power amplifiers for some radars and SCPC.