• 설비공학논문집
• /
• 제4권3호
• /
• pp.191-203
• /
• 1992

To analyze the unsteady heat transfer phenomena in radiant heating panel, a mathematical model was considered. Numerical analysis for solving the governing equations was conducted by using the finite difference method with boundary-fitted meshes. Transient temperature distributions and thermal responses in heating panel were obtained for various design parameters such as pipe pitches, pipe diameters and pipe depths. Experimental results were also obtained to verify the results of calculation.

• 대한기계학회논문집B
• /
• 제22권12호
• /
• pp.1774-1783
• /
• 1998

The transition from steady laminar to chaotic convection in a glass melting furnace specified by upper surface temperature distribution has been studied by the direct numerical analysis of the two and three-dimensional time dependent Navier-Stokes equations. The thermal instability of convection roll may take place when modified Rayleigh number($Ra_m$) is larger than $9.71{\times}10^4$. It is shown that the basic flows in a glass melting furnace are steady laminar, unsteady periodic, quasi-periodic or chaotic flow. The dimensionless time scale of unsteady period is about the viscous diffusion time, ${\tau}_d=H^2/{\nu}_0$. Through primary and secondary instability analyses the fundamental unsteady feature in a glass melting furnace is well defined as the unsteady periodic or weak chaotic flow.

• 대한기계학회논문집B
• /
• 제27권2호
• /
• pp.243-250
• /
• 2003

The extinction behavior and the unsteady response of augmented reduced mechanism(ARM) have been investigated by adopting an OPPDIF code and a numerical solver for the flamelet equations. By comparing the performance of the ARM based on Miller and Bowman's mechanism(MB-ARM) with that of the ARM based on GRI-Mech 3.0(GRI-3.0-ARM), it is identified that the MB-ARM is more suitable for the unsteady calculation because it is relatively less stiff than GRI-3.0-ARM during an ignition process. The steady results using the MB-ARM, which is modified to predict reasonably the extinction point of experiment, are in excellent agreement with those from full mechanism. Under the sinusoidal transient disturbances of scalar dissipation rate, the unsteady responses of the flame temperature and species concentrations using a modified MB-ARM show in very close agreement with those from full mechanism. It is presumed that above modified MB-ARM is very suitable for the unsteady simulation of turbulent flames because it gives not only a low computational cost but also a good prediction performance for flame structure, extinction point and unsteady response.

• 동력기계공학회지
• /
• 제10권4호
• /
• pp.25-30
• /
• 2006

This paper represents the numerical analysis in unsteady state on the variation of diameter and environmental velocity of carbon heating source. In general heating system, the oil and sheath heater is widely used, but these systems have many problems. So, the heating source with carbon ingredient has been researched in many country about manufacture, thermal and electrical properties. In this research, the carbon heating source was studied through numerical analysis on several conditions of unsteady state, heat generation, diameter and environmental velocity. The temperature distributions at steady state are appeared as a non-proportional linear pattern with variations of environmental velocity due to the Nesselt number with convective heat flux is proportioned to 0.805 of Reynolds number. As the radius is increasing, the temperature distributions is appeared the minus tilt because of the environmental condition is cooling by constant temperature. So, the correlation equation between temperature at steady state and environmental velocity was obtained.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2000년도 추계 학술대회논문집
• /
• pp.54-59
• /
• 2000

A numerical study of axisymmetric rocket main nozzle flow has been accomplished. The CSCM upwind flux difference splitting method with an iterative time marching scheme having second order accuracy in time and space has been used to simulate unsteady flow characteristics in an axisymmetric rocket main nozzle. Though the pressure vary at nozzle inlet with the lapse of time, Mach No. and the density were not changed significontly compared with the temperature. Specific heat ratio $\gamma$=1.134 predicted higher temperature at nozzle throat and exit and nondimensional thrust coefficients at exit than specific heat ratio $\gamma$=1.4 did.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년도 제31회 추계학술대회논문집
• /
• pp.221-226
• /
• 2008

본 연구에서는 연소실내 유동으로 인해 발생하는 연소실 축방향 압력변화를 고려한 비정상 내탄도 해석모델을 개발하고 이를 바탕으로 침식연소를 해석하였다. 개발 모델은 선행 연구와 비교하였으며 해석결과가 일치함을 확인하였다. 연소실 압력, 그레인 길이, 그레인 초기온도, 추진제 기화온도가 침식연소에 미치는 영향을 조사하였다.

• 한국추진공학회지
• /
• 제13권2호
• /
• pp.17-25
• /
• 2009

본 연구에서는 연소실의 축방향 압력과 속도변화를 고려한 비정상 내탄도 해석모델을 제안하고 이를 바탕으로 침식연소에 미치는 인자를 해석하였다. 개발 모델의 검증을 위하여 침식연소가 없는 경우와 침식연소가 있는 경우에 대하여 선행연구 결과와 비교하였으며 해석결과가 일치함을 확인하였다. 연소실 압력, 그레인 길이, 그레인 초기온도, 추진제 기화온도가 침식연소에 미치는 영향을 조사하였다.

• 동력기계공학회지
• /
• 제5권3호
• /
• pp.48-55
• /
• 2001

In many applications. rubber components undergo dynamic stresses or deformations of fairly large magnitude. Since rubbers are not fully elastic, a part of the mechanical energy is converted into heat due to the hysteresis loss. Heat generation without adequate heat dissipation leads to heat build up. i. e. internal temperature rise. The purpose of this paper is to predict temperature rise caused by the hysteresis loss, in a rubber pad subjected to complex dynamic deformation. In this unsteady thermal analysis, the temperature distributions of track components are displayed in contour shapes and the temperature variations of some important nodes are represented graphically with respect to the running time of the tank.

• 오토저널
• /
• 제12권3호
• /
• pp.41-52
• /
• 1990

In this study are determined the unsteady temperature and thermal stress fields for a domestic 4-cylinder, 4-cycle gasoline engine cylinder head by the three-dimensional finite element method. A representative part of the cylinder head is modelled as a combination of hexahedron isoparametric elements, and the time-dependent temperature and the heat transfer coefficient of the gas are imposed as the thermal boundary conditions for the engine speeds of 500 rpm and 2000 rpm. The obtained results, which are represented graphically, indicate that the amplitudes of temperature fluctuation during a cycle are about 10.deg. C and 3.deg. C respectively on the surface of combustion chamber, and the maximum temperature fields occur at 30.deg. , 10.deg. respectively before the initiation of the exhaust stroke. Thermal stress fields due to non-uniform temperature distributions show that compressive stress is much larger than tensile stress throughout a cycle. It is also found that the compressive stress varies with substantial amplitude between the exhaust port and ignition plug hole, and the high tensile stress with small fluctuation occurs between exhaust port and the adjacent head bolt hole.

• 설비공학논문집
• /
• 제27권12호
• /
• pp.633-638
• /
• 2015

This study evaluates the capacity of night purging in office buildings to reduce the cooling load. RTS-SAREK is used to estimate the performance of night purging on the steady state. To overcome steady state RTS program limitations, we added unsteady heat transfer equations. When the ACH (Air Change per Hour) increases, the wall temperature decreases in both the steady and unsteady states. The unsteady heat transfer rate is different from the steady transfer rate, which validates the unsteady calculation. When ACH is low, the heat transfer rate increases continuously with time. When ACH becomes higher, the heat transfer rate increases and decreases with time. When ACH is quite high, there exists a large difference in the heat transfer rate between the steady and unsteady calculations, which emphasizes the importance of the unsteady calculation.