• Korean Journal of Remote Sensing
• /
• v.33 no.5_3
• /
• pp.809-820
• /
• 2017

Efficient management of large-size wastes generated from disasters etc. is always in demand. Large-size wastes are closely connected to the environment, producing adverse effects on the air quality, water quality, living environment and so on. When large-size wastes are generated, we must be able to estimate the generated amount in order to transfer them to a temporary trans-shipment site, or to properly treat them. Currently, we estimate the amount of generated large-size wastes by using satellite images or unit measure for wastes; however, the accuracy of such estimations have been constantly questioned. Therefore, the present study was performed to establish three-dimensional spatial information based on UAS, to measure the amount of waste, and to evaluate the accuracy of the measurement. A measurement was made at a waste site by using UAS, and the X, Y, Z RMSE values of the three-dimensional spatial information were found to be 0.022 m, 0.023 m, and 0.14 m, all of which show relatively high accuracy. The amount of waste measured using these values was computed to be approximately $4,273,400m^3$. In addition, the amount of waste at the same site was measured by using Terrestrial LiDAR, which is used for the precise measurement of geographical features, cultural properties and the like. The resulting value was $4,274,188m^3$, which is not significantly different from the amount of waste computed by using UAS. Thus, the possibility of measuring the amount of waste using UAS was confirmed, and UAS-based measurement is believed to be useful for environmental control with respect to disaster wastes, large-size wastes, and the like.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.2
• /
• pp.101-112
• /
• 2016

This study investigated the removal of Sr, which was one of the high radioactive nuclides, by adsorption with Barium (Ba) impregnated 4A zeolite (BaA) from high-radioactive seawater waste (HSW). Adsorption of Sr by BaA (BaA-Sr), in the impregnated Ba concentration of above 20.2wt%, was decreased by increasing the impregnated Ba concentration, and the impregnated Ba concentration was suitable at 20.2wt%. The BaA-Sr adsorption was added to the co-precipitation of Sr with $BaSO_4$ precipitation in the adsorption of Sr by 4A (4A-Sr) within BaA. Thus, it was possible to remove Sr more than 99% at m/V (adsorbent weight/solution volume)=5 g/L for BaA and m/V >20 g/L for 4A, respectively, in the Sr concentration of less than 0.2 mg/L (actual concentration level of Sr in HSW). It shows that BaA-Sr adsorption is better than 4A-Sr adsorption in for the removal capacity of Sr per unit gram of adsorbent, and the reduction of the secondary solid waste generation (spent adsorbent etc.). Also, BaA-Sr adsorption was more excellent removal capacity of Sr in the seawater waste than distilled water. Therefore, it seems to be effective for the direct removal of Sr from HSW. On the other hand, the adsorption of Cs by BaA (BaA-Cs) was mainly performed by 4A within BaA. Accordingly, it seems to be little effect of impregnated Ba into BaA. Meanwhile, BaA-Sr adsorption kinetics could be expressed the pseudo-second order rate equation. By increasing the initial Sr concentrations and the ratios of V/m, the adsorption rate constants ($k_2$) were decreased, but the equilibrium adsorption capacities ($q_e$) were increasing. However, with increasing the temperature of solution, $k_2$ was conversely increased, and $q_e$ was decreased. The activation energy of BaA-Sr adsorption was 38 kJ/mol. Thus, the chemical adsorption seems to be dominant rather than physical adsorption, although it is not a chemisorption with strong bonding form.

• Korean Journal of Food Science and Technology
• /
• v.12 no.3
• /
• pp.170-175
• /
• 1980

A mass production of chestnut necessiates the development of economic long-term storage method. The main objective of this study was to confirm the technical aspect of the chestnut storage method which was developed by two year project and to review the method of commercial application. The chestnut used for the experiments were separated in brine $(5.5{\sim}6.0^{\circ}\:B{\acute{a}}ume)$ into matured and unmatured lots and fumigated with $CS_2$ at a 5 $lb/27\;m^3$ level for $25{\sim}30\;hrs.$ The chestnuts were packed in wooden boxes with sawdust (50% moisture) in the ratio of 1 : 1 by volume. The boxes were stored in the cold room $(1{\pm}1^{\circ}C,\;85{\sim}95%\;RH)$ and the cellar ($0{\sim}10^{\circ}C$, controlled only by circulating night cool air). The results obtained were as follows: 1. Fully matured chestnut could be successfully preserved $8{\sim}9\;months$ at a l0% decay level in the cold room and $4{\sim}5\;months$ months in cellar. 2. Immatured chestnuts wire inferior to the matured in storage stability. At the maximum storage period, its storage life was two months shorter. 3. The heat transfer equation of piled chestnuts with sawdust can be suggested as $T_{\infty}-T_0=(T_{\infty}-T_0){\cdot}10^{-t/320}$ and j and $f_h$ values were 1 and 320 min, respectively. 4. The chestnuts in the package of storage unit had longer shelf life than naked chestnut during the retail distribution at ambient temperature.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.1 no.1
• /
• pp.18-28
• /
• 1978

To study about the effect of harvested stage and physical treatment such as wilting or chopping of plant material on the quality of silage, Italian ryegrass(Lolium multiflorum) harvested at pre-headed or heading stage and Seombadi(Dystaenia takesimana Nakai) harvested at pre-flowering stage, were used for the purpose. The materials were treated in four different ways which were a) non-treated, b) one day-wilted, c) chopped with 1 to 2cm length and d) wilted and chopped, and those were ensiled in plastic containers and stored at room temperature for three months. After three months of storage, it was investigated and obtained the following results. 1) Having 6.31 of NFE/CP ratio and low content of crude fiber, Seombadi contained more suitable constituents for silage than Italian ryegrass. 2) Under the non-treated or chopped condition, the loss of NFE was higher, and lower with wilted material. 3) Wilting or chopping improved DM digestibility. 4) Compared with Italian ryegrass harvested at pre-headed stage, the storage amount per unit volume of heading stage-Italian ryegrass and Seombadi were higher 8% and 69% respectively, and wilting and/or chopping increased the storage amount 41 to 134%. 5) The majority of weight loss during storage was observed at 1st week after ensiling, it continued slightly until 4th week. The highest loss in 8th week were 3.76% of nontreated material. 6) One day wilting increased DM content of silage 23 to 131%. Wilting and chopping increased pH and lactic acid improved the quality considerably. 7) The correlation between $NH_3$ and butyric acid, and between lactic acid and DM were r=0.782**, r=0.634** respectively. The regression equation were y=12.853X+4.908 (X=butyric acid), y=0.016X+1.309(X=DM content), respectively. 8. The above results indicate that it is necessary to wilt or chop material to make good quality silage from Italian ryegrass, and such treatment can improve the quality of silage with Seombadi also.

• Journal of the Korean Society of Food Culture
• /
• v.5 no.1
• /
• pp.59-75
• /
• 1990

The tzeam is the one of steaming cook that boiled the main material of poultry. meat and the sub-material of vegetables. It is always setted on the main-table in above seven chup ban sang and also kyoja sang. In this thesis, according to the kinds of tzeam in the main material of poultry, meat was to analysis reference frequency to them the materials, the measuring unit of materials, the terms of cooking and kitchen utensil by 47 books published in Korea from 1420 to 1987. 1. It was 37 kinds of tzeam in the main material of poultry, meat. 2. Materials were classified into the main-material, sub-materials, seasioning and decorations. 3. There were 43 kinds of measuring units, of them 18 kinds were for volume, 12 kinds were for quantity, 4 kinds were for length and the rest measuring units were 9 kinds. 4. There were 26 kinds of kitchen utensil for cooking. They were mainly used a hab 1 rice ball with lids, and castles (cast iron castle). 5. There were 27 kinds of cooking terms. The terms of them, 11 kinds were for heating methods, 16 terms of them were for the cutting process.

• Progress in Medical Physics
• /
• v.24 no.4
• /
• pp.295-302
• /
• 2013

We estimated secondary scattered and leakage doses for intensity-modulated radiotherapy (IMRT), volumetric arc therapy (VMAT) and tomotherapy (TOMO) in patients with liver cancer. Five liver patients were planned by IMRT, VMAT and TOMO. Secondary scatter (and leakage) dose and organ equivalent doses (OEDs) are measured and estimated at various points 20 to 80 cm from the iso-center by using radiophotoluminescence glass dosimeter (RPLGD). The secondary dose per Gy from IMRT, VMAT and TOMO for liver cancer, measured 20 to 80 cm from the iso-center, are 0.01~3.13, 0.03~2.34 and 0.04~1.29 cGy, respectively. The mean values of relative OED of secondary dose of VMAT and TOMO for five patients, which is normalized by IMRT, measured as 75.24% and 50.92% for thyroid, 75.14% and 40.61% for bowel, 72.30% and 47.77% for rectum, 76.21% and 49.93% for prostate. The secondary dose and OED from TOMO is relatively low to those from IMRT and VMAT. OED based estimation suggests that the secondary cancer risk from TOMO is less than or comparable to the risks from conventional IMRT and VMAT.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.4
• /
• pp.341-348
• /
• 2010

The basic principle of fry drying process of sludge lies in the rapid pressure change of sludge material caused by the change of temperature between oil and moisture due to the difference of specific heat. Therefore, the rapid increase of pressure in drying sludge induces the efficient moisture escape through sludge pores toward heating oil media. The object of this study is to carry out a systematic investigation of the influence of various parameters associated with the sludge fry drying processes on the drying efficiency. To this end, a series of parametric experimental investigation has been made together with the numerical calculation in order to obtain typical drying curves as function of important parameters such as drying temperature, sludge diameter, oil type and sludge type. In the aspect of frying temperature, especially it is found that the operation higher than $140^{\circ}C$ was favorable in drying efficiency regardless of type of waste oil employed in this study. The same result was also noted consistently in the investigation of numerical calculation, that is, in that the sludge particle drying was efficiently made over $140^{\circ}C$ irrespective of the change of particle diameter. As expected, in general, the decrease of diameter in sludge was found efficient both experiment and numerical calculation in drying due to the increased surface area per unit volume. In the investigation of oil type and property, the effect of the viscosity of waste oil was found to be more influential in drying performance. In particular, when the oil with high viscosity, a visible time delay was noticed in moisture evaporation especially in the early stage of drying. However, the effect of high viscosity decreased significantly over the temperature of $140^{\circ}C$. There was no visible difference observed in the study of sludge type but the sewage sludge with a slightly better efficiency. The numerical study is considered to be a quite useful tool to assist in experiment with more detailed empirical modeling as further work.

• Journal of Chest Surgery
• /
• v.31 no.5
• /
• pp.456-465
• /
• 1998

Cardiopulmonary bypass(CPB) in children is associated with the accumulation of body water after cardiac operation, as a consequence of an inflammatory capillary leak. Following work by Elliott in 1991, modified ultrafiltration(MUF) was introduced after bypass as a means of hemoconcentrating patients and a potential way of removing water from the tissues. We have carried out a prospective randomized study of 20 children undergoing open heart surgery, comparing MUF with nonfiltered controls. MUF was carried out for a mean of 18.9 minutes after completion of CPB to a hematocrit of 37.1%(mean). The mean water volulme removed by the ultrafiltration was 38.4 ml/kg and the mean blood volume retransfused from the oxygenator during the ultrafiltration was 32.1 ml/kg. Fluid balance, hemodynamics, hematocrit, osmolarity and dosage of drug treatment were recorded for 4∼12 hours postoperatively. The results were analyzed using Student t-test and ANOVA, comparing controls(n=10) to MUF(n=10). Blood loss(ml/kg/24hr) was 14.5(mean) in MUF versus 13.7 in controls; blood transfused(ml/kg/24hr) 6.6 in MUF versus 15.2 in controls; plasma transfused(ml/kg/24hr) 65.7 in MUF versus 59.6 in controls. There was rise in arterial blood pressure and hematocrit during MUF. Percent rise of systolic blood pressure was 28.8% in MUF versus 18.7% in controls(p=0.366); percent rise of diastolic blood pressure was 28.8% in MUF versus 8.5% in controls(p=0.135); and percent rise of mean blood pressure was 36.2% in MUF versus 8.2% in controls (p=0.086). Percent rise of hematocrit was 40.0% in MUF versus 23.5% in controls(p=0.002). There was no significant difference in the inotropic requirement and the postoperative serum osmolarity between two groups. The number of days on the ventilator, the duration of stay in the intensive care unit, and the postoperative hospital stay were not significantly different between the two groups.

• Journal of Korean Society of Transportation
• /
• v.30 no.2
• /
• pp.101-116
• /
• 2012

Accident prediction models have been utilized to predict accident possibilities in existing or projected freeways and to evaluate programs or policies for improving safety. In this study, a traffic accident prediction model for freeways was developed for the above purposes. When selecting variables for the model, the highest priority was on the ease of both collecting data and applying them into the model. The dependent variable was set as the number of total accidents and the number of accidents including casualties in the unit of IC(or JCT). As a result, two models were developed; the overall accident model and the casualty-related accident model. The error structure adjusted to each model was the negative binomial distribution and the Poisson distribution, respectively. Among the two models, a more appropriate model was selected by statistical estimation. Major nine national freeways were selected and five-year dada of 2003~2007 were utilized. Explanatory variables should take on either a predictable value such as traffic volumes or a fixed value with respect to geometric conditions. As a result of the Maximum Likelihood estimation, significant variables of the overall accident model were found to be the link length between ICs(or JCTs), the daily volumes(AADT), and the ratio of bus volume to the number of curved segments between ICs(or JCTs). For the casualty-related accident model, the link length between ICs(or JCTs), the daily volumes(AADT), and the ratio of bus volumes had a significant impact on the accident. The likelihood ratio test was conducted to verify the spatial and temporal transferability for estimated parameters of each model. It was found that the overall accident model could be transferred only to the road with four or more than six lanes. On the other hand, the casualty-related accident model was transferrable to every road and every time period. In conclusion, the model developed in this study was able to be extended to various applications to establish future plans and evaluate policies.

• Radiation Oncology Journal
• /
• v.7 no.2
• /
• pp.213-225
• /
• 1989

An analysis has been made of two hundred seven patients who were treated at the department of Radiation Oncology of Korea University Hospital for lung cancer from January 1981 through December 1986. There were 137 patients of nonsmall cell carcinoma (137/207, 66%), 26 patients of small cell carcinoma (26/207, 12.5%) and 44 patients of unproven histology. By aims of treatment, there were 104 patients (104/207, 50%) treated for cure, 89 patients (89/207, 42.9%) for palliation and 14 patients treated postoperatively. In 22 out of 207 patients, chemotherapy was done with radiotherapy, 12 of which were patients with small cell carcinoma. Stage II patients were 49 (49/207, 23.6%), stage III patients were 157 (157/207, 75.8%) and one patient had an occult cancer The tumor was initial Iy measured by CAT scan and chest X-rays in the 165 (165/207, 79.7%) patients, among which 117 patients had tumor diameter more than 5cm and 48 patients less than 5cm. Radiation therapy was given with Cobalt 60 teletherapy unit and the treatment volume encompassed primary tumor and the mediastinum. For curative aim, daily tumor dose of 180 cGy was given up to the range of 5,400~6,120cGy/30~34F/6~7 week period and for palliative aim, daily tumor dose of 300 cGy was given up to the range of 3,600~4,500 cGy/12~15F/2~3 week period. Postoperatively, mediastinum was treated for total dose of 5,040 cGy/28F/5.5 week period. 123 patients (123/207, 59%) were followed up after completion of radiotherapy for 14 months to 7 years. Local tumor response to the irradiation was measured by chest X-ray taken at one month follow up and was evaluated for response rate, if they were regressed more than 50% or less than 50% of the initial tumor size. The treatment results were as follows; 1. The median survival time was 8.5 months and survival rates for 1 year, 2 year and 5 year was 25%, 3.5% and 1% of nonsmall cell lung ca of 74 evaluable patients. 2. More than 50% of local tumor response rate was obtained in about half of overall cases; 90.5% for small cell ca, 50% for squamous cell ca, 25% for adenoca and 57% for large cell ca. 3. Response rate more than 50% was seen in the 50% of the patient group with tumor diameter more than 5cm and in the 55% of those with tumor diameter less than 5cm. 4. By total raidation dose given, patient group which was given 5,400~6,120 cGy equivalent dose or higher showed tumor response rate more than 50% in 53% of the patients, whereas the group with dose less than 5,400cGy equivalent, in 25% of the patients. 5. Survival rate for 6 month, 1 year and 2 year was compared between the group of local tumor response rate more than 50% vs. group with response rate less than 50%; 74% vs. 43%, 33% vs, 23%, 10% vs. 1%, respectively. 6. Local failure was seen in 21%(44/207) of the patients, which occured mostly within 15 months after completion of radiation therapy. Distant metastases were seen in 49.7%(103/207) of the patients, of which 43 cases were found before initiation of radiotherapy. The most common metastatic sites were bone and brain. In this sutdy, 1 year,2 year and S year survival rates were somewhat poor compared to the other studies. It mainly seems to be due to the poor general status of the patients and the far-advanced stage of the disease. In nonsmall cell cancer patients who had limited local disease and had small primary tumor size, we observed better local response. In addition, dose higher than 6,000 cGy group showed better tumor control than lower dose group. Survival rate was better for the local control group. For imporvement of local control of the lung cancer and hence, the survival of the patients with lung cancer, proper radical radiotherapy with high dose for localized disease is needed. New modality of treatment such as high LET beam in radiation therapy or drugs for the advanced disease as well as early diagnosis is also needed.