• Journal of computational fluids engineering
• /
• v.18 no.2
• /
• pp.35-40
• /
• 2013

Natural convection of air with Pr=0.7 between two horizontal plates with small magnitude non-uniform temperature distribution[${\in}{\Delta}Tsin({\kappa}X/H)$, H : gap width, X : horizontal coordinate] in the lower plate is numerically(${\in}=0.01$) investigated. In the conduction-dominated regime with $Ra{\leq}1700$, two upright cells are formed over one wave length($2{\pi}/{\kappa}$). For small wave number, the flow becomes unstable with increase of Rayleigh number, and multicellular convection occurs above a critical Rayleigh number. The flow patterns are classified by the number of eddies over one wave length. When ${\kappa}=1$, a transition of $2{\rightarrow}4{\rightarrow}6$ eddy flow occurs with increase of Rayleigh number, and no hysteresis phenomenon is observed. Dual and triple solutions are found for ${\kappa}=1$, and transitions of $10{\rightarrow}8$, $8{\rightarrow}6$, $6{\rightarrow}4{\rightarrow}2$ eddy flow occur with decrease of Rayleigh number.

• Journal of the Korean Society of Safety
• /
• v.12 no.4
• /
• pp.27-38
• /
• 1997

The effect of geometry factors on the combined mode stress intensity factor behaviors of a slant crack in a non-uniform thickness material was analysed by 2-dimensional theoretical analysis. The analysis is based on the Laurent's series expansions of complex potentials where the complex coefficients of the series are determined from the compatibility and the equilibrium conditions of the thickness interface and the stress free conditions of the crack surface. In numerical calculations the perturbation technique is employed. The expressions for the crack tip stress intensity factor are given in the form of power series of dimensionless crack length $\lamda$, and the function of crack slant angle $\alpha$ and thickness ratio $\beta$. The results of numerical calculations for each problems are represented as the correction factors F($\lamda$, $\alpha$, $\beta$). The results clearly show the following characteristics : The correction factors of the combined mode stress intensity factors for a non-uniform thickness material can be defined in the form of F($\lamda$, $\alpha$, $\beta$). The stress intensity factor values for a given crack length are decreased with increase of thickness ratio $\beta$.

• Journal of Fashion Business
• /
• v.20 no.2
• /
• pp.1-15
• /
• 2016

Currently, a lot of people are aware of their health and well-being, so they are concerned about their healthcare. 'Taekwondo' is one of the popular sports that Korean people are passionate about Taekwondo has also become globalized. The uniform of Taekwondo is gaining importance. Taekwondo involves a lot of movement, hence the pattern should facilitate the movement. In addition Taekwondo uniform pattern should meet the demands of functionality, fit and consumer design preferences. This study aimed to provide the basic data for development of Taekwondo uniform pattern based on design preferences and functionality to wearer satisfaction. The result of this method indicated fit and design details. Also, the length of pants, top, and sleeve was too wide, which has to more fitted for both of genders. For females, the breakpoint was too low, which requires some increase to make females feel more secure. In conclusion, the results of this study indicated that in order to increase 'Takwondo' value, Taekwondo uniform is required to be more fashionable and comfortable to wear, which could influence other sports wear.

• Proceedings of the KWS Conference
• /
• 2006.05a
• /
• pp.304-306
• /
• 2006

Positioning the workpiece accurately and preventing the weld distortion, tack welding is often performed before main welding in the construction of welded structures. The weld bead size of the tack weld is determined according to the workpiece thickness, weld length, weld joint type etc. However, this tack weld deteriorates the final weld bead profile, so that the grinding process is usually adopted for the uniform weld bead profile. In this study, an experimental method for the selection of optimal welding condition was proposed in the fillet weld which was done over the tack weld. This method uses the response surface analysis in which the leg length and the reinforcement height of weld bead were chosen as the quality variables of weld bead profile. The overall desirability function, which was combined desirability function for the two quality variables, was used as the objective function for getting the optimal welding condition. From the result, it was revealed that a uniform weld bead can be obtained by adopting the optimal welding condition which was determined according to the method proposed.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.20 no.1
• /
• pp.29-33
• /
• 1983

The loading condition, of a ship, especially a multi-purpose cargo carrier, in service, is often changed. Then, the prediction of natural frequency changes is necessary to provide measures for prevention of ship vibrations. In this paper a simplified method for the above purpose is presented. The bases of the method are analytical solutions for the lateral vibrations of uniform Timoshenko beams carrying a concentrated mass and the Dunkerley's formula. In this method a ship in the standard ballast condition is reduced to a uniform Timoshenko beam having same system parameters as those of the midship section. To investigate the validity of the proposed method, numerical calculations are carried out for a 46,000 DWT bulk carrier and compared with detailed calculations based on the finite difference method. Even in cases those the cargoes in a hold, length of which is about 13% of the ship's length, are reduced to a concentrated mass, the proposed method gives results of several percent differences from the detailed calculations up to the six-noded mode.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.1 no.2
• /
• pp.101-107
• /
• 2009

The VIV (Vortex-Induced Vibration) analysis of a flexible cylindrical structure under locally strong shear flow is presented. The model is made of Teflon and has 9.5m length, 0.0127m diameter, and 0.001m wall thickness. 11 2-dimensional accelerometers are installed along the model. The experiment has been conducted at the ocean engineering basin in the University of Tokyo in which uniform current can be generated. The model is installed at about 30 degree of slope and submerged by almost overall length. Local shear flow is made by superposing uniform current and accelerated flow generated by an impeller. The results of frequency and modal analysis are presented.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.209-215
• /
• 2000

Precision forging technology that can control flow velocity of workpiece have been developed to minimize the amounts of machining. To get the uniform rib length, flow velocity distribution is needed to be estimated and controlled. Computer-aided design is known for very effective to estimate the deformation behavior and design the die for controlling the flow velocity. In this study, die design to control the deformation velocity are investigated using the DEFORM-2D about rib-web shape parts. Also we can get uniform rib length by enforcing the back pressure at end section of rib. The applied load of back pressure farming is lower than that of conventional forging. These results are analysed and confirmed by the experiment.

• Journal of the Chungcheong Mathematical Society
• /
• v.23 no.4
• /
• pp.785-791
• /
• 2010

In this note, we give a characterization of cycle lengths of uniform cellular automata configured with rules 60 or 102.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.26 no.6
• /
• pp.263-268
• /
• 2014

Eskilson's g-function, a well-known geothermal heat response factor, is widely used for sizing of the ground heat exchangers. Unlike the Eskilson's original model that uses common temperature boundaries for all boreholes and along the borehole height, an analytical-solution-based g-function uses a uniform heat transfer rate over the height with variable heat transfer rates for respective boreholes. To evaluate the impact of such a boundary difference on g-function and the design length, a simple case study was carried out on the cooling-dominant commercial buildings. The results show that the design lengths given by the boundary of uniform heat transfer rates are longer than those given by Eskilson's boundary for all cases tested. The difference in length is more important when the bore field is composed of more boreholes with shorter length of each borehole.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.2
• /
• pp.38-44
• /
• 2022

Plasma density in semiconductor fabrication equipment becomes higher to achieve the improved the throughput of the process, but the increase of surface corrosion of the ceramic coated chamber wall has been observed by the increased plasma density. Plasma chamber wall coating with aerosol deposition prefer to be firm and uniform to prevent the potential creation of particle inside the chamber from the deformation of the coating materials, and the aerosol discharge nozzle is a good control factor for the deposited coating condition. In this paper, we investigated the design of the nozzle of the aerosol deposition to form a high-quality coating film. Computational fluid dynamics (CFD) study was employed to minimize boundary layer effect and shock wave. The degree of expansion, and design of simulation approach was applied to found out the relationship between the divergence angle and nozzle length as the key parameter for the nozzle design. We found that the trade-off tendency between divergence angle and nozzle length through simulation and quantitative analysis, and present the direction of nozzle design that can improve the uniformity of chamber wall coating.