• 한국광학회지
• /
• 제14권3호
• /
• pp.219-223
• /
• 2003

광섬유의 잔류응력(residual stress)을 측정하기 위해 위상보정 편광기(polariscope)를 새롭게 구성하고, 간섭이나 회절에 대한 영향을 최소화시키면서 빠르고 정확하게 측정하는 방법을 제시하였다. 이 방법을 이용하여 일반 광섬유의 잔류 응력 분포를 측정할 수 있었다. 또한 광섬유의 잔류응력이 모재의 잔류응력분포와 달리 인출 시 발생하는 광섬유 내 온도의 냉각곡선에 밀접한 관계를 갖고 있음을 알 수 있었다.

• The Journal of Advanced Prosthodontics
• /
• 제10권2호
• /
• pp.138-146
• /
• 2018

PURPOSE. The purpose of this study was to analyze the effects of the splinted implant prosthesis in a reconstructed mandible using three-dimensional finite element analysis. MATERIALS AND METHODS. Three-dimensional finite element models were generated from a patient's computed tomography data. The patient had undergone partial resection of the mandible that covered the area from the left canine to the right condyle. The mandible was reconstructed using a fibula bone graft and dental implants. The left mandibular premolars and molars remained intact. Three types of models were created. The implant-supported prosthesis was splinted and segmented into two or three pieces. Each of these models was further subcategorized into two situations to compare the stress distribution around normal teeth and implants. Oblique loading of 300 N was applied on both sides of the mandible unilaterally. The maximum von Mises stress and displacement of the models were analyzed. RESULTS. The stress distribution of the natural mandible was more uniform than that of the reconstructed fibula. When the loading was applied to the implant prosthesis of reconstructed fibula, stress was concentrated at the cortical bone around the neck of the implants. The three-piece prosthesis model showed less uniform stress distribution compared to the others. Displacement of the components was positively correlated with the distance from areas of muscle attachment. The three-piece prosthesis model showed the greatest displacement. CONCLUSION. The splinted implant prosthesis showed a more favorable stress distribution and less displacement than the separated models in the reconstructed mandible.

• 항공우주시스템공학회지
• /
• 제13권6호
• /
• pp.1-8
• /
• 2019

아음속 유동이 흐르는 후향 계단에서, 입구 경계면에서의 난류를 모사하는 3가지 기법을 조사하였다. 입구 경계면으로 유입되는 평균 유동장과 레이놀즈 응력 프로파일은 실험에서 측정된 결과를 사용하였으며, 입구 경계면의 난류 유동 모사기법으로 synthetic eddy method(SEM), 무작위 변동(random noise) 그리고 균일한 유동 조건(uniform)을 사용하였다. 3차원 유동장의 난류 유동의 모사를 위해 대와동모사(Large Eddy Simulation, LES)를 적용하였다. 3가지 기법에 대한 입구 경계면으로 유입된 유동의 난류 특성과 유동의 재 부착(reattachment) 거리와 속도, 레이놀즈 응력(Reynolds stress)을 비교하였다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.100-105
• /
• 2002

This paper predicts the material properties of spatially reinforced composites (SRC) and analyzes the thermo-elastic behavior of a kick motor nozzle manufactured from that material. To find the appropriate SRC structure for the nozzle throat that satisfies given design conditions, the equivalent material properties of the SRC are predicted using the superposition method for those of rod and matrix. Studied are the elastic behavior, temperature distribution, and thermo-elastic behavior of a kick motor nozzle composed of carbon/carbon SRC as a throat part. The elastic deformation of the nozzle composed of 3D carbon/carbon SRC shows asymmetry in a circumferential direction. However, 4D carbon/carbon SRC nozzle shows uniform deformation in the circumferential direction. Stress concentration in connecting parts of the kick motor nozzle is ultimately high due to the high temperature gradient in each connecting part. The thermo-elastic deformations of both the 3D and the 4D SRC nozzles are uniform in the circumferential direction due to the isotropy of CTE of each SRC. The deformation of the 3D SRC nozzle is a slightly smaller than that of the 4D SRC nozzle in the nozzle throat, which is favorably effective on rocket thrust. The circumferential stress is the most critical component of the kick motor nozzle. The 4D SRC nozzle having 1,1,1,1.7 diameters in each direction has the smallest circumferential stress among several SRC nozzles.

• 한국산학기술학회논문지
• /
• 제13권8호
• /
• pp.3295-3300
• /
• 2012

3차원 유한요소법은 구조물에 존재하는 표면균열과 내재균열들의 응력확대계수를 구하는데 이용되어 진다. 기하모델, 즉 솔리드모델은 3차원 균열들을 포함하고 있다. 국부적인 절점밀도가 선택되어 지면 자동적으로 기하모델 영역에 중첩되어 지며 절점은 버블패깅 방법에 의해 생성되어지고 10절점 사변형 솔리드요소는 데라우니 삼각화 기술에 의해 생성하였다. 시스템의 정확도와 효용성을 체크하기 위해 인장하중을 받는 평판에 하나의 균열이 존재하는 경우의 응력확대계수를 구해 Raju-Newnam식과 비교하여 5%이내의 차이를 보였다. 또한, 인장하중을 받는 평판에 두개 균열이 존재하는 경우의 해석을 통해 상호 간섭 효과를 분석하였다.

• Structural Engineering and Mechanics
• /
• 제57권3호
• /
• pp.543-567
• /
• 2016

This study attempts to address the buckling and free vibration characteristics of an isotropic cylindrical panel subjected to non-uniform temperature rise using numerical approach. Finite element analysis has been used in the present study. The approach involves three parts, in the first part non-uniform temperature field is obtained using heat transfer analysis, in the second part, the stress field is computed under the thermal load using static condition and, the last part, the buckling and pre-stressed modal analysis are carried out to compute critical buckling temperature as well as natural frequencies and associated mode shapes. In the present study, the effect of non-uniform temperature field, heat sink temperatures and in-plane boundary constraints are considered. The relation between buckling temperature under uniform and non-uniform temperature fields has been established. Results revealed that decrease (Case (ii)) type temperature variation field influences the fundamental buckling mode shape significantly. Further, it is observed that natural frequencies under free vibration state, decreases as temperature increases. However, the reduction is significantly higher for the lowest natural frequency. It is also found that, with an increase in temperature, nodal and anti-nodal positions of free vibration mode shapes is shifting towards the location where the intensity of the heat source is high and structural stiffness is low.

• 한국공간구조학회논문집
• /
• 제18권2호
• /
• pp.69-78
• /
• 2018

In current research, it was attempted a preliminary design and evaluation of non-uniform ultra high-strength concrete (UHSC) truss members. UHSC used here has the compressive strength of 180 MPa, the tensile strength of 8 to 20 MPa, and the tensile strain after cracks up to 2%. By the three-dimensional finite element stress analysis as well as strut-tie approach on concrete solid beams, the non-uniform truss shape of UHSC truss was designed with the architectural esthetic concept. In a series of examples, to compare with conventional concrete members, the proposed UHSC truss members have advantages in capabilities of the slender design with minimum weight with high performances under transverse loadings as well as the aesthetically non-uniform design for spatial structures.

• 한국기계가공학회지
• /
• 제16권5호
• /
• pp.13-18
• /
• 2017

In this work the augmented safety of Type 4 composite vessel in accordance with uniform-stress design has been demonstrated through a series of burst tests and structural analyses. For this end, three sample vessels were used: (1) designed as guided by the isotensoid dome theory (called iso-dome cylinder); (2) with dome longer compared to uniform-stress design (called prolate cylinder); and (3) with dome wider than uniform-stress design (called oblate cylinder). Structural analyses have been performed using ABAQUS finite element code based on the periodic symmetry to circumferential direction. As a result, the maximum stresses are induced around the bodies of all three cylinders. However, the analyses, with the assumption of possible defect demonstrate that the maximum stresses are induced around the dome knuckles for the prolate and the oblate cylinders. The results of the burst tests for the three cylinders show that the burst initiates from the cylinder body of the iso-dome cylinder and from the dome knuckles of the prolate and the oblate cylinders. Finally, it is recommended that, to comply with DOT CFFC 2007, the dome shape should be designed and fabricated as guided by the isotensoid dome theory.

• 대한기계학회논문집B
• /
• 제20권6호
• /
• pp.2023-2035
• /
• 1996

In the present study, the characteristics of the electrical deformation of a bubble and a drop under a uniform electric field have been investigated to understand EHD heat transfer enhancement by an electric field. The deformation of the bubble and the drop have been studied theoretically using an electric normal stress acting on their interfaces and assured by the numerical analysis and the experiment. From the variation of bubble volume and free energy, it is found that a bubble is compressed in an electric field and free energy had larger value with increasing W and the permittivity of a dielectric fluid. The electric normal stress induced on the interface of the bubble and the drop is different. Because of the surface charge induced at the drop interface, the electric normal stress acting on the drop is much larger than that of the bubble. The drop is, therefore, deformed much more than the bubble. In addition, the experimental and numerical results show that the aspect ratio and the contact angle of the bubble increase with increasing W.

• 한국전산구조공학회논문집
• /
• 제32권3호
• /
• pp.183-190
• /
• 2019

본 논문은 균열선단 그리드 세분화기법을 소개하고 자연요소법을 이용한 균열해석에 이 기법을 적용함으로서 그 유효성을 고찰하였다. 유한요소법에 있어서의 국부적 h-세분화와 같이 높은 응력 특이성을 보이는 균열선단 주위를 따라 자연요소법 그리드를 국부적으로 세분화하였다. 본 논문에서 소개되는 그리드 세분화기법은 2단계로 구성되며, 1단계에서는 그리드 점들이 추가되고 2단계에서는 균열선단 절점을 공유하는 델라우니 삼각형들이 나뉘게 된다. 제안하는 그리드 세분화기법의 타당성과 균열해석에서의 유효성을 입증하기 위해 대칭 엣지 균열을 갖는 평면 변형률 상태의 사각 평판을 해석하였다. 수치해석 결과의 상대비교를 위해 균일한 자연요소 그리드를 이용한 균열해석도 수행하였으며, 균열선단이 세분화된 그리드는 균일한 그리드와는 달리 이론해와 조밀한 그리드와 유사한 균열선단 응력분포를 나타내었다. 또한, 총 그리드 절점수에 대한 해석결과의 전역 상대오차에서도 세분화된 그리드가 균일한 그리드에 비해 높은 수렴율 나타내었다.