• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1216-1220
• /
• 1992

본 연구에서는 Lee등의 연구를 일반화하기 위하여 급수 형태의 등각사상함수 로 표현되는 일반형태의 커스프형 강체함유물이 존재하는 경우에 대하여 복소 포텐셜 함수와 TSIF에 대한 일반해를 구하기로 한다.

• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.79-84
• /
• 1996

One of the greatest dangers in mechanical face seals is the formation of heat checking and thermal stress cracks on the sliding surfaces. These thermal distortions due to non-uniform heating lead to increase the leakage of the sealed fluids and wear, and with balance of the seal can cause the seal faces to part. In this study heat checking and thermal stress cracks are investigated experimentally. These thermal distortions are explained using the thermal models of the conatct geometries between the seal ring and the seal seat. To overcome these thermal problems, the thermohydrodynamic seal is presented. The newly developed mechanical seal may substantially reduce the friction torque, frictional heating which causes heat checking and thermal stress cracks, and wear.

• Corrosion Science and Technology
• /
• 제14권4호
• /
• pp.161-165
• /
• 2015

This paper presents an analysis of thermal stress induced along the interface between a polymeric coating layer and a steel substrate as a result of uniform temperature change. The epoxy layer is assumed to be a linear viscoelastic material and to be theromorheologically simple. The viscoelastic boundary element method is employed to investigate the behavior of interface stresses. The numerical results exhibit relaxation of interface stresses and large stress gradients, which are observed in the vicinity of the free surface. Since the exceedingly large stresses cannot be borne by the polymeric coating layer, local cracking or delamination can occur at the interface corner.

• Structural Engineering and Mechanics
• /
• 제4권4호
• /
• pp.397-413
• /
• 1996

In this paper the elastic post-buckling behaviour of plates under non-uniform compressive edge stress is investigated. The compatibility differential equations is first solved analytically and then an approximate solution of the equilibrium equation is obtained using the Galerkin method. Explicit expressions are derived for the load-deflection, ultimate strength and membrane stress distributions. Analytical effective width formulations, based on the characteristics of the stress field of the buckled plate, are proposed for this general loading condition. The predicted load-deflection expression is compared with independent test results. Results are also presented detailing the load-deflection behaviour and stress distribution for various aspect ratios.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.405-408
• /
• 2004

The forming load and the stress applied to dies during cold forming of automotive part using microalloyed forging steel are examined with finite element analysis. The forming load and the stress applied to dies at each process step are investigated for two types of forming process. The changes in forming process significantly affect the variation of firming load and the stress at each process step, thus it is considered that the die lift will be remarkably changed with the type of forming process, therefore optimal process design is necessary to obtain an increased the die life and to make the die life uniform at each process step.

• 대한기계학회논문집A
• /
• 제24권3호
• /
• pp.560-566
• /
• 2000

Many researchers have dealt with the problems of fracture mechanics. Generally, these researches are concerned with crack in isotropic material without other micro defects. Actual structure, however, may contain micro defects as well as crack in manufacture processing or operation. If it contains mi defects near a crack, some different characteristics will be appear in fracture behaviors of the crack. This study examines the effect of the micro defect on stress intensity factor of center slant crack rectangular plate subjected to uniform uniaxial tensile stress. In this study, boundary element method(BEM) is used for analysis in stress intensity factor(SIF).

• 한국생산제조학회지
• /
• 제9권3호
• /
• pp.76-82
• /
• 2000

It is well known that during the oxygen cutting process residual thermal stresses are produced in weldment. The local non-uniform heating and subsequent cooling which takes place during any welding process causes complex thermal strains and stresses to finally lead to residual stresses exceed to the yield stress. High tensile stresses combined with applied structural load in the region near the welded joint can given rise to distortion brittle fracture change of the fatigue strength and stress corrosion cracking. The appropriate treatment of the welded component which reduces the peak of he welding residual stresses is believed to lower risk of the fracture during the service of the structure. In this study the impact loading in oxygen cutting frame was applied to reduce the residual stress. After applying the impact loading redistribution of resid-ual stress was measured by cutting method and the effect of fatigue was tested.

• 한국철도학회논문집
• /
• 제7권2호
• /
• pp.125-129
• /
• 2004

This study investigates the fatigue lift estimation of butt weld specimen for the railway vehicle by examining butt weld bead profiles. The butt weld beads, which are welded by semi-robot method, have non-uniform bead profiles described by $\theta$, p and h. The stress concentration factors, K$\_$t/, are changed by different $\theta$, p and h from 1.395 to 2.863. Hence, the sensitivity of K$\_$k/ is changed by each $\theta$, p and h. As $\theta$ becomes lower and p and h become higher, K$\_$t/ increases. The fatigue life can be estimated very closely for the AAY specimens without residual stress using only butt weld bead profiles. But, for the AAN specimens with residual stress, the fatigue life must be estimated by considering both the weld bead profiles and the residual stress data.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2001년도 봄 학술발표회 논문집
• /
• pp.97-104
• /
• 2001

The magnitude and the orientation of in-situ stresses contribute to ground displacement and stresses in the field of underground space. This paper investigates in-situ stresses at various depth on the basis of 392 data which were determined by over-coring and hydro-fracturing test methods in the Korea peninsula. The result shows that in-situ stress distribution are more or less non-uniform through the Granite and Gneiss sub-area, and that the K-value in the Volcanic sub-area are below 1 at the deep depth. Also, the result of three dimensional numerical analyses of tunnel shows that the direction and magnitude of displacement around tunnel are much effected by the stress difference between the maximum and the minimum horizontal stress.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2007년도 제28회 춘계학술대회논문집
• /
• pp.212-216
• /
• 2007

Predicting microcracking properties of the composite laminates in nonuniform stress conditions was the subject in this paper. The uniform stress field meant the stresses were independent of the width direction. The material was the 954-2A/IM7 laminates containing a central hole. Microcracks initiated at the edge of the hole and propagated into the laminate. Because the tensile stress concentration decreased with distance, the microcracks were arrested before the edge of the laminate. Because carbon fiber composites were opaque, a x-ray method was used to detect the length of the propagating microcracks. The microcracking at the near edge of the hole could be reasonably predicted by considering the local laminate stresses and the microcracking toughness measured in unnotched laminates. However, the date away from the hole did not agree with the predictions. The local microcrack density was always much higher than that predicted by the local laminate stress.