• 한국강구조학회 논문집
• /
• 제14권6호
• /
• pp.803-811
• /
• 2002

일반적으로 강콘크리트 합성형교는 불완전합성에 대한 해석의 복잡함 때문에 강재와 콘크리트 계면에서의 상대변위가 발생하지 않는 완전합성형으로 설계된다. 그러나, 이러한 설계는 기존 강합성형 의 거동을 평가하는 경우 실제 구조물의 내하력과 내구성을 정확하게 도출하지 못하게 된다. 이러한 경우에는 불완전합성이론을 이용하여 구조물의 거동을 정확히 반영해야 한다. 본 연구에서는 집중하중을 받는 단순합성형교에 대하여 처짐 거동을 고려한 불완전합성곡률의 변화양상을 확인하기 위하여 유한요소해석 모델을 이용하여 전단연결재의 배치간격과 배치열수 그리고 콘크리트 탄성계수를 매개변수로 선택하여 해석을 수행하였다. 본 연구의 결과로서 합성형의 처짐이 증가할수록 불완전합성 정도가 증가함을 알 수 있었으며, 콘크리트 슬래브에서 균열이 발생으로 인한 강성 및 강도의 감소가 합성정도에 큰 영향을 미치는 것을 알 수 있었다.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 추계학술발표대회
• /
• pp.35.1-35.1
• /
• 2011

New photovoltaic (PV) materials and manufacturing approaches are needed for meeting the demand for lower-cost solar cells. The prototypal thin-film photovoltaic absorbers (CdTe and $Cu(In,Ga)Se_2$) can achieve solar conversion efficiencies of up to 20% and are now commercially available, but the presence of toxic (Cd,Se) and expensive elemental components (In, Te) is a real issue as the demand for photovoltaics rapidly increases. To overcome these limitations, there has been substantial interest in developing viable alternative materials, such as $Cu_2ZnSnS_4$ (CZTS) is an emerging solar absorber that is structurally similar to CIGS, but contains only earth abundant, non-toxic elements and has a near optimal direct band gap energy of 1.4~1.6 ev and a large absorption coefficient of ${\sim}10^4\;cm^{-1}$. The CZTS absorber layers are grown and investigated by various fabrication methods, such as thermal evaporation, e-beam evaporation with a post sulfurization, sputtering, non-vacuum sol-gel, pulsed laser, spray-pyrolysis method and electrodeposition technique. In the present work, we report an alternative method for large area deposition of CZTS thin films that is potentially high throughput and inexpensive when used to produce monolithically integrated solar panel modules. Specifically, we have developed an aqueous chemical approach based on chemical bath deposition (CBD) with a subsequent sulfurization heat treatment. Samples produced by our method were analyzed by scanning electron microscopy, X-ray diffraction, transmission electron microscopy, absorbance and photoluminescence. The results show that this inexpensive and relatively benign process produces thin films of CZTS exhibiting uniform composition, kesterite crystal structure, and good optical properties. A preliminary solar cell device was fabricated to demonstrate rectifying and photovoltaic behavior.

• 한국전산유체공학회지
• /
• 제16권4호
• /
• pp.39-46
• /
• 2011

A numerical study of a turbulent natural convection in an enclosure with the lattice Boltzmann method (LBM) is presented. The primary emphasis of the present study is placed on investigation of accuracy and numerical stability of the LBM for the turbulent natural convection flow. A HYBRID method in which the thermal equation is solved by the conventional Reynolds averaged Navier-Stokes equation method while the conservation of mass and momentum equations are resolved by the LBM is employed in the present study. The elliptic-relaxation model is employed for the turbulence model and the turbulent heat fluxes are treated by the algebraic flux model. All the governing equations are discretized on a cell-centered, non-uniform grid using the finite-volume method. The convection terms are treated by a second-order central-difference scheme with the deferred correction way to ensure accuracy and stability of solutions. The present LBM is applied to the prediction of a turbulent natural convection in a rectangular cavity and the computed results are compared with the experimental data commonly used for the validation of turbulence models and those by the conventional finite-volume method. It is shown that the LBM with the present HYBRID thermal model predicts the mean velocity components and turbulent quantities which are as good as those by the conventional finite-volume method. It is also found that the accuracy and stability of the solution is significantly affected by the treatment of the convection term, especially near the wall.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1740-1743
• /
• 2007

In this study, two types of fatigue tests were conducted. First, cyclic bending tests were performed using the micro-bending tester. A four-point bending test method was adopted, because it induces uniform stress fields within a loading span. Second, thermal fatigue tests were conducted using a pseudo power cycling machine which was newly developed for a realistic testing condition. The pseudo-power cycling method makes up for the weak points in a power cycling and a chamber cycling method. Two compositions of solder are tested in all test condition, one is lead-free solder (95.5Sn4.0Ag0.5Cu) and the other is eutectic lead-contained solder (63Sn37Pb). In the cyclic bending test, the solder that exhibits a good reliability can be reversed depending on the load conditions. The lead-contained solders have a longer fatigue life in the region where the applied load is high. On the contrary, the lead-free solder sustained more cyclic loads in the small load region. A similar trend was detected at the thermal cycling test. A three-dimensional finite element analysis model was constructed. A finite element analysis using ABAQUS was performed to extract the applied stress and strain in the solder joints. A constitutive model which includes both creep and plasticity was employed. Thermal fatigue was occurred due to the creep. And plastic deformation is main damage for bending failure. From the inelastic energy dissipation per cycle versus fatigue life curve, it can be found that the bending fatigue life is longer than the thermal fatigue life.

• 한국동물생명공학회지
• /
• 제35권3호
• /
• pp.245-257
• /
• 2020

Behavioral response to a diel photoperiodicity (500 lx for 16 h, 5 lx for 4 h and < 0.5 lx for 4 h) and phototactic characteristics in dark conditions were examined with Siberian sturgeon Acipenser baerii (Chondrostei, Actinopterygii) prelarvae. Siberian sturgeon prelarvae represented both qualitative and quantitative changes in their behavioral patterns according to different light intensities in a diel photoperiodicity. Under daylight conditions (500 lx), prelarvae displayed saltatory changes of behavioral features with ages (Day 0-Day 9) in a general order of swimming-up/drifting, swimming in the upper water column, benthic swimming with rheotaxis, schooling and post-schooling behavior. Compared to daylight conditions, prelarvae tended to show more benthic performances and quantitative reductions of schooling and post-schooling behaviors under dimlight conditions (5 lx). Under dark conditions (< 0.5 lx), prelarvae exhibited a fairly uniform behavioral pattern characterized by the benthic swimming across the bottom of the tank. From phototaxis tests under dark conditions, navigational responses of prelarvae to a spotlight illumination were quantitatively changed as their ages increased. The phototactic responses reached the peak on Day 2, continued until Day 4, and then gradually decreased until Day 8. A partial recovery of positive phototaxis was observed on Day 9. Data from this study suggest that the diel light cycle as well as the light intensity of each interval in the cycle should be considered as important components of a practical guide for evaluating fitness and developmental states of artificially propagated Siberian sturgeon prelarvae.

• 한국주조공학회지
• /
• 제32권2호
• /
• pp.98-103
• /
• 2012

Recently, development of Al-based alloys for high mechanical performance has been an important issue in automotive industry. The present study focused on the design of a high strength Al-based alloy for rheo-diecasting. The research was based on thermodynamic calculation and experimentals to optimize the alloy compositions. Two important considerations were carried out: i) to obtain uniform slurry with fine and globular microstructures for rheo-diecasting, ii) to be strengthend by T6 heat treatment. In order to evaluate the effect of Si content on the slurry microstructure and castability, thermodynamic calculation and fluidity test were carried out. The effects of various alloying components, such as Mg, Cu and Zn, on age hardenability were also investigated. The mechanical properties of the rheo-diecasting products using the newly developed alloy are 324MPa in tensile strength, 289MPa in yield strength, and 11.2% in elongation after T6 heat treatment.

• 한국추진공학회지
• /
• 제23권6호
• /
• pp.51-58
• /
• 2019

본 연구에서는 소형 무인기에 사용되는 초소형 가스터빈 엔진의 연소기를 3D 프린팅으로 제작하고, 시험 설비와 리그를 제작하여 연소기 단품 성능시험을 수행하였다. 연소기 성능시험은 두 가지 부하조건에서 당량비를 조절하여 각 부하조건 별 4가지 시험조건에서 수행하였다. 성능시험 결과 연소기의 압력손실과 출구온도분포는 우수하였지만, 연소가스에서 다량의 UHC와 CO가 검출되어 연소효율은 일반적인 가스터빈 연소기에 비해 아주 낮음을 확인하였다. 성능시험을 통해 획득한 정량적 성능데이터는 향후 3D 프린팅 기술로 성능이 개선된 연소기의 설계와 제작에 활용 할 예정이다.

• 천문학회지
• /
• 제29권spc1호
• /
• pp.151-154
• /
• 1996

We examine the observations of large-scale magnetic fields in the Universe. We begin at the largest scale with clusters of galaxies and work our way down through galaxies and finally to the Milky Way. on which we concentrate in detail. We examine the observations of the Galactic magnetic field, and their interpretation, under the philosophy that the Galactic magnetic field is like that in other spiral galaxies. We use pulsar data. diffuse Galactic synchrotron emission, and starlight polarization data to discuss the Galaxy's global magnetic configuration and the uniform ($B_u$), random ($B_r$), and total ($B_t$) components of the field strength. We find disagreement among conclusions derived from the various data sets and argue that the pulsar data are not the best indicator for large-scale Galactic field. Near the Solar circle, we find that the azimuthal average of $B_t$ is 4.2$\mu$G and we adopt $B_u\~$2.2 and $B_r\~3.6{\mu}G$. $B_t$ is higher in spiral arms, reaching $\~5.9{\mu}G$. $B_t$ is higher for smaller $R_{Gal}$, reaching $\~8.0{\mu}G$ for $R_{Gal}$ = 4.0 kpc. The pattern of field lines is not concentric circles but spirals. The inclination of the magnetic spiral may be smaller than that of the Galaxy's spiral arms if our sample, which refers primarily to the interarm region near the Sun, is representative. However, it is not inconceivable that the local field lines follow the Galaxy's spiral pattern, as is observed in external galaxies.

• 복식
• /
• 제61권3호
• /
• pp.122-138
• /
• 2011

The present research aims to consider the real remains of 2 suits of Kasaya owned by the Hwaeom Temple(華嚴寺) based on research results about Kasaya in the meanwhile. The present research on 2 suits of remains which are Royal gifts given to monk soldiers in case of a national crisis of the Joseon Dynasty has a big meaning in examining characteristics of Kasaya and grasping characteristics and structure of the 17th century's Kasaya of the Joseon Dynasty through dense survey and analysis according to components. If examining characteristics of Kasaya, the Kasaya of the Great Monk Seo San(西山) is composed on the basis of an initial form of Sun and Moon Light Patch's generation and the Kasaya of the Great Monk Byeok Am(碧巖) has a form that is separately attached through production of embroidery patch as a process of being settled down. If examining what surrounds gold thread in the girth and expression of Sumeru and Chaeunmun(彩雲紋), the composition of a form similar to an insignia badge, so because this is a Royal gift, this can be estimated as being analyzed in a Buddhism aspect by devising a design from the insignia badge at the time, with a meaning like an official uniform given to a monk. Although the insignia badge is a square, it seems that the Sun and Moon Light Patch is made as a rectangular form corresponding to the structure of Kasaya. In addition, it is thought that what the Samjoko(三足烏) idea which is a symbol of the Sun based on Buddhism and Taoism is used together with Yijoko(二足烏) even in expression of the Sun and Moon Light Patch in the Joseon Dynasty which was a Confucian country has a relationship with what a bird was expressed in the insignia badge of winged animals.

• 한국생산제조학회지
• /
• 제22권2호
• /
• pp.263-267
• /
• 2013

The continuing demand for increasingly slimmer and brighter liquid crystal display (LCD) panels has led to an increased focus on the role of light guide panels (LGPs) or optical films that are used to obtain diffuse, uniform light from the backlight unit (BLU). The most basic process in the production of such BLU components is the micromachining of V-shaped grooves. Thus, given the current trend, micromachining of V-shaped grooves is expected to play increasingly important roles in today's manufacturing technology. LCD BLUs comprise various optical elements such as a LGP, diffuser sheet, prism sheet, and protector sheet with V-shaped grooves. High-aspect-ratio patterns are required to reduce the number of sheets and enhance light efficiency, but there is a limit to the aspect ratio achievable for a given material and cutting tool. Therefore, this study comprised a series of experimental evaluations conducted to determine the machining limit in microcutting V-shaped grooves on electroless nickel plated die materials when using single-crystal diamond tools with point angles of $20^{\circ}-80^{\circ}$. Cutting performance was evaluated at various cutting speeds and depths of cut using different machining methods and machine tools. The experimental results are that V-shaped patterns with angles of $80^{\circ}$ or up can be realized regardless of the machining conditions and equipment. Moreover, the feed rate has little effect on machinability, and it is thought that the fly-cut method is more efficient for shallow patterns.