• 한국정보디스플레이학회:학술대회논문집
• /
• 2000.01a
• /
• pp.187-188
• /
• 2000

The conventional firing process method for the transparent dielectric layer in PDP Technology has disadvantages of low through put, high power consumption and large process area. We propose the rapid thermal scinterring (RTS) method as new process method to overcome these disadvantage characteristics. As the experimental result of this method, the optic transmittance(wavelength : 600nm) rate of transparent dielectric layer was more improved than conventional furnaces under the optimized gas supplying. Further, it was certified this method had the best conditions on the firing process of the PDP transparent dielectric layer.

• Journal of the Korean Ceramic Society
• /
• v.15 no.4
• /
• pp.213-223
• /
• 1978

The purpsoe of this study was to produce domestic stamping materials; sling mass which could be used as unburned refractory for iron melt'ladle. Batch compositions were based on Belgian Ladelite; mineral compositions were composed of 84 wt% of quartz and 16 wt% of clay, and particle sizes were divided into 12 wt% of 1410/297㎛, 18wt% 297/149㎛, 20wt% of 149/74㎛, 11wt% 74/44㎛ and 39wt% 44㎛ under. The effect of variable batch compositions were also investigated such as substitution of pyrophylite or industrial grade alumina for quartz and of zircon for portion of quartz and clay, increase of clay and addition on sericite. Samples were pressed at 100kg/㎠ with 7.4wt% of water or 7.4wt% of 4 wt% PVA solution. Dried and Fired properties of samples such as linear shrinkage, apparent porosity, modulus of rupture, refractoriness and corrosion resistance to blast furnace slag were investigated. The results are summarized as follows. 1. Dried samples are shrinked, but fired at 700-1400℃ expanded. Samples fired at 700-1000℃ and 1200-1400℃ tended to expand with incresing of firing temperature, but fired at 1000-1200℃ tended to shrink with increase of firing temperature. 2. Apparent porosity of samples fired at 700℃ is increased, but fired at 1200-1400℃ decreased with increasing of firing temperature. 3. Modulus of rupture of samples fired at 700℃ is decreased, but fired at above 700℃ increased with increasment of firing temperature. 4. Dried samples with 7.4 wt% of 4 wt% PVA solution better improve modulus of rupture than with 7.4 wt% of water, but the firing strength of the sampels fired at 700-1000℃ is showed reversely. 5. In quartz-clay system, mineral phases of samples fired at above 1200℃ are consisted of α-quartz, α-cristobalite and mullite. Respectively as firing temperature was rising up, intensity of α-cristobalite and mullite is in creased. 6. Quartz-Kibushi clay system, Kimcheun quartz(substitutuion of portion of industrial grade alumina for quartz) Hampyeung clay system and pyrophyllite-clay system are better in corrosion resistance to blast furnace slag than burned pyrophyllite brick. 7. 84 wt% of pyrophyllite-16wt% of clay system is superior in modulus of rupture and corrosion resistance to blast furnace slag to 84 wt% of quartz-16 wt% of clay system.

• The Journal of Korean Academy of Prosthodontics
• /
• v.29 no.3
• /
• pp.111-119
• /
• 1991

This study was performed to investigate the effect of gold electrodepositoin on porcelain color of palladium-silver alloy. The specimens were made by firing porcelain on the metal plates cast respectively in Au-Pt alloy, and Pd-Ag alloy. In the case of Pd-Ag alloy specimens, porcelain were fired under three different conditions of the metal plate: 1) without gold coating, 2) firing opaque beforehand on one side, gold coating on the other side, 3) gold coating on both sides of the metal plate. Color change was measured with fiber-optic colorimeter(Model TC-6FX, Tokyo Denshoku Co., Japan). The obtained results were as follows: 1. In the group of firing opaque beforehand on one side and gold coating on the other side, there was no significant differences in their color in comparison to the color of the control group of the Au-Pt alloys. 2. In the group of gold coating on both sides on metal plate, there were no significant differences except their value to the group of firing poaque beforehand on one side and gold coating on the other side.

• Journal of the Korean Ceramic Society
• /
• v.55 no.2
• /
• pp.116-125
• /
• 2018

Color shade variation was investigated in zirconia dental blocks, prepared using commercial powders. As a reference color-shade block we used the color indexes of A2, A3.5, A4 and B3, according to the VITA classical color scale. The zirconia powders for color shade blocks showed colors of white, yellow, pink and grey, respectively, after firing at $1530^{\circ}C$. The zirconia powders were mixed according to the recipe of color shade blocks and shaped at lower pressure using a uniaxial hydrostatic press. The shaped sample was inserted into a vinyl pack and sealed in a vacuum form machine. The shaped block samples were reshaped at 450 bar using an isostatic cold press and fired at $1530^{\circ}C$ for three hours. In order to investigate the atmospheric color variation with firing temperature, the A2, A3.5, A4 and B3 sintered blocks were fired between $700^{\circ}C$ and $1300^{\circ}C$ under controlled atmosphere of $pN_2$ and $pO_2$. The surface color picture was taken using a smart phone camera and compared with the results obtained using the VITA classical color scale. Quantitative color index value, CIELAB, was measured using a color-meter. Above $800^{\circ}C$, the color darkness greatly increased with the increase of the reduction temperature and keeping time.

• Journal of the Korean Ceramic Society
• /
• v.17 no.2
• /
• pp.69-74
• /
• 1980

This study deals with the wire content, wire diameter, aspect ratio , it's arrangement of steel, wire fiber and the sorts of castable which affected the character of steel wire fiber reinformced refractory castable. Two kinds of alumina based refractory castables, one is for 1650℃ and the other is for 1800℃, and stainless steel which is SUS 304 type 0.25, 0.34 , 0.37 and 0.50m/min diameter were used respectively. Aspect ratio was adjusted to 50, 75, 100 and steel fiber content was also adjusted to 1-4wt% each. The results of the experiment were as follows : 1. At firing temperature around 1,000℃, MOR is increased with increasing wire content and aspect ratio with decreasing firing temperature, which depends on the Romualdi's Fiber Spacing Theory. But for calculation of the fiber spacing, Swamy equation is more a aplicable to the extensive fiber mixing conditions. However, the condition differs from the above at firing temperature around 1,350℃ ,because of the degradation of wire and the progress of sintering of castable. 2. Linear change is getting larger corresponding to the increase of wire content, and the spaling resistivity is increasing corresponding to the increase of wire content and to aspect ratio, and with decreasing wire diameter. 3. Firing shrinkage under load is getting greater as higher wire content, and the shrinkage of the test pieces which fiber is vertically oriented is getting greater than the test pieces which fiber is randomly oriented.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.84-90
• /
• 2004

A performance evaluation is made in terms of thrust, impulse bit. and specific impulses for a set of mono-propellant hydrazine thrusters producing 0.95 lbf of nominal thrust at an inlet pressure of 350 psia. With a brief description on the hot-firing test configuration and procedures. a typical data obtained from steady-state firing mode is given directly showing the variational behavior of propellant supply pressure, mass flow rate, vacuum condition, and thrust. The performance features are successfully compared to the reference criteria of 1-lbf standard mono-propellant rocket engine. Additionally. a statistical inter-thruster treatment is concisely depicted for the justification of selected thrusters as a grouped member of flight model for spacecraft propulsion system.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.19-28
• /
• 2000

In general the data such as thrust, pressure, temperature and combustion time are measured in developing the propulsion system of solid rocket motor through static firing test. But in the case of personal surface to air missile there are required a severe safety specifications in order to eliminate gunner hazard from the exhaust plume of motors. The safety requirements lead to the design of separation device and safety igniter device. The dynamic firing test for the designed two devices should be conducted under the flight environmental conditions to verify the requirements compliance. In this study the technique for dynamic firing test of propulsion system of personal surface to air missile is proposed and the method to design the dynamic test bench is also studied.

• The Journal of Korean Academy of Prosthodontics
• /
• v.32 no.1
• /
• pp.47-76
• /
• 1994

This study was carried out to evaluate the effect of the crack propagation characteristics and bond stress of ceramo-metal system. In order to characterize the crack propagation, the static crack propagation stored in $37^{\circ}C$ distilled water of two commerical porcelains and the dynamic crack propagation under cyclic flexure load of ceramo-metal system were examined. In order to characterize the bond stress, the shear bond test, the 3-point flexure bond test, and the finite element stress analysis of ceramo-metal system were conducted. The results obtained were as follows : 1. Bulk densities and Young's moduli of opaque porcelains increased with repeated firing. 2. Maximum fracture toughness during 4 firing cycles showed at the group of 4 firing cycles in Ceramco porcelain and 2 firing cycles in Vita porcelain. 3. Shear bond strength and flexure bond strength of Ceramco-Verabond specimen were larger than those of Ceramco-Degudent G specimen (p<0.05). 4. Interfacial stresses under three point flexure bond test were concentrated at the edges of ceramometal system. 5. When a cyclic flexure load was applied, the crack growth rate of porcelain surface of ceramometal specimens was decreased as load cycles increased.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.4 s.109
• /
• pp.319-328
• /
• 2006

This paper presents a method for analysis of the mechanical behavior of a crankshaft in a four-cylinder internal combustion engine. The purpose of the analysis was to study the characteristics of the shaft in which the pin and arm parts were assumed to have a uniform section in order to simplify the modal analysis. The results of natural frequency transfer function and mode shape were compared with those obtained by experimental work. The results obtained from the comparison showed a good agreement with each other and consequently verified the analysis model. Furthermore, a prediction of crankshaft characteristics under the firing condition, by using the model, was performed. This study describes a new method for analyzing the dynamic behavior of crankshaft vibrations in the frequency domain based on the initial firing stages. The new method used RMS values to calculate the energy at each bearing journal and counter weight shape modification under the operating conditions.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.6
• /
• pp.68-75
• /
• 2011

This study simulated the effect of steam injection on the performance and operation of a gas turbine combined heat and power (CHP) system. A commercial simple cycle gas turbine was analyzed. A full off-design analysis was carried out to investigate the variations in not only engine performance but also the operating characteristics of the compressor caused by steam injection. Variation in engine performance and operation characteristics according to various operation modes were examined. First, the impact of full steam injection was investigated. Then, operations aiming to guarantee a minimum compressor surge margin, such as under-firing and partial steam injection, were investigated. The former and latter were turned out to be relatively superior to each other in terms of power and efficiency, respectively.