• Journal of the Korean Society for Nondestructive Testing
• /
• v.5 no.1
• /
• pp.24-33
• /
• 1985

A study has been made on the correlation between ultrasonic attenuation and mechanical properties with different prior austenite grain size. It was found that ultrasonic attenuation is increased with increasing grain size, decreasing yield strength and increasing charpy impact energy value for ALSI 4140 steel.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.21 no.6
• /
• pp.612-617
• /
• 2001

A nondestructive evaluation technique for detecting internal defects of an hot forged Al-Si alloy part is established in this study. Ultrasonic characteristics of various internal planar defects are investigated by experiments for establishing a reliable test procedure. The effect of the angle between ultrasonic energy propagation directions and planar defects on the ultrasonic signal configuration is evaluated in the pulse-echo technique. A characteristic of ultrasonic signal for the internal planar defect located near the edge is also evaluated. The applicability of the through-transmission technique is also discussed. Reliability of the presented approach is validated by the destructive testing for more than 500 specimens.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.1 no.1
• /
• pp.32-38
• /
• 1981

• Journal of the Korean Society for Nondestructive Testing
• /
• v.12 no.1
• /
• pp.9-15
• /
• 1992

Ultrasonic spectroscopy is likely to become a very powerful NDE method for detection of microfects and thickness measurement of thin film below the limit of ultrasonic distance resolution in the opaque materials, provides a useful information that cannot be obtained by a conventional ultrasonic measuring system. In this paper, we considered a thin film below the limit of ultrasonic distance resolution sandwitched between two substances as acoustical analysis model, demonstrated the usefulness of ultrasonic spectroscopic analysis technique using information of ultrasonic frequency for measurements of thin film thickness, regardless of interference phenomenon and phase reversion of ultrasonic waveform. By using frequency intervals(${\triangle}f$) of periodic minima from the ratio of reference power spectrum of reflective waveform obtained a sample to power spectrum of multiple reflective waves obtained interference phenomenon caused by ultrasonic waves reflected at the upper and lower surfaces of a thin layer, can measured even dimensions of interest are smaller than the ultrasonic wave length with simplicity and accuracy.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2003.10a
• /
• pp.190-194
• /
• 2003

Two different types of nondestructive evaluation (NDE) techniques were employed to investigate the tensile behavior of ceramic matrix composites (CMCs). Two NDE methods, ultrasonic testing (UT) and infrared (IR) thermography, were used to assess defects and/or damage evolution before and during mechanical testing. Prior to tensile testing, a UTC-scan and a xenon flash method were performed to obtain initial defect information in light of UT C-scans and thermal diffusivity maps, respectively. An IR camera was used for in-situ monitoring of progressive damages. The IR camera measured temperature changes during tensile testing. This paper has presented the feasibility of using NDE techniques to interpret structural performance of CMCs.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.1
• /
• pp.32-37
• /
• 2002

The presence of hydrogen in industrial plants is a source of damage. Hydrogen attack is one such form of degradation and often causing large tube ruptures that necessitate an immediate shutdown. Hydrogen attack may reduce the fracture toughness as well as the strength of steels. This reduction is caused partially by the presence of cavities and microcracks at the grain boundaries. In the past several techniques have been used with limited results. This paper describes the application of an ultrasonic velocity and attenuation in hydrogen damage. Ultrasonic tests showed a decrease in wave velocity and an increase in attenuation. Such results demonstrate the potential for ultrasonic nondestructive testing to quantify damage. Based on this study, reliable recommendation is suggested to detect hydrogen attack.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.5 no.2
• /
• pp.34-41
• /
• 1986

The ultrasonical characteristics of inclined planar reflectors is investigated by the maximum amplitude method. The reflected ultrasound is varied by the reflector size, shape, inclination and using transducers. It was found that the detecting ability for planar reflectors was decreased with increasing transducer size and misorientation angle and increased with decreasing ultrasonic frequency, also the misorientation angle of planar reflectors affected significantly for the measurement of refklector size.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.2 no.4
• /
• pp.172-176
• /
• 1998

강관 등과 같이 곡면을 이루는 구조물 용접부의 내부 결함을 검출하기 위한 기법을 제안하였다. 인공 결함을 만들어 초음파 비파괴검사를 행하고, 곡면의 표면 거리($Y_s$)를 계산하여 실측한 참값($Y_T$)과 비교해 보았다. 제안된 방법으로 계산한 값이 참값에 대하여 1%이하의 오차 범위에 들어오므로 강관 용접부의 내부 결함 검사에 응용될 수 있다.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.2
• /
• pp.91-102
• /
• 2008

Nondestructive testing techniques have been historically and commonly used to evaluate the quality of existing concrete structures. The techniques utilized included visual inspection, hammer sounding, Schmidt hammer rebounding, and ultrasonic pulse velocity testing including tomographic imaging. Results of the nondestructive tests were used to determine areas to be tested with local destructive tests. These tests included concrete compressive strengths, chloride testing, and petrographic testing. The overall results indicate that inside core of each of the pier caps are healthy. On all of the pier caps, extensive exterior concrete layer rehabilitation needs to be completed. This paper shows the application and interpretation of common nondestructive testing techniques and the consequent repair, rehabilitation, maintenance decisions and safety assesment.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.18 no.3
• /
• pp.163-171
• /
• 1998

Near/far field length and directivity of transducers were investigated for the improvement and evaluation of the detectability of flaws in a disc. The reference block is fabricated for the disc of stage 6 in Yonggwang unit 1. The near/far field and directivity of an ultrasonic transducer with the center frequency of 5MHz were calculated for the inspection of the disc. These values showed good agreements with the experimental results. In the system composed of a wedge and a disc, those are evaluated theoretically and experimentally for the specimen with the artificial flaws of the size 2mm and 4mm and an ultrasonic transducer with the center frequency 5MHz and diameter 0.5inch. The detectability of keyway-flaw and detectable region for inspection were evaluated by using both tangential $45^{\circ}$ and $90^{\circ}$ transducers located at the distance of 53mm and 75mm from the disc hub, respectively.