• 비파괴검사학회지
• /
• 제2권1호
• /
• pp.5-9
• /
• 1982

Experiments were performed according to ultrasonic attenuation measurement and comparison method of DAC curve to analyze the difference between PSI and 2nd ISI ultrasonic testing results. Smaller error was found by comparison method of DAC curve, and that method was more useful practically.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 춘계학술대회논문집A
• /
• pp.31-36
• /
• 2000

High temperature and pressure materials in power plant are degraded by creep damage, if they are exposed to constant loads for long times, which occurs in the load bearing structures of pressurized components operating at elevated temperatures. Many conventional measurement techniques such as replica method, electric resistance method, and hardness test method for measuring creep damage have been used. So far, the replica method is mainly used for the Inspection of High temperature and pressure components. This technique is, however, restricted to applications at the surface of the testpieces and cannot be used to material inside. In this paper, ultrasonic evaluation for the detection of creep damage in the form of cavaties on grain boundaries or integranular microcracks are carried out. And the absolute measuring method of quantitative ultrasonic velocity technique for Cr-Mo material degradation is analyzed. As a result of ultrasonic tests for crept specimens, we find that the sound velocity is decreased as the increase of creep life fraction$({\Phi}_c)$ and also, confirmed that hardness is decreased as the increase of creep life fraction$({\Phi}_c)$ but the coefficient of ultrasonic attenuation is increased as the increase of creep life fraction$({\Phi}_c)$. Finally based on the result in this paper, it can be recognized that the ultrasonic techniques using velocities and attenuation coefficient factor are very useful non-destructive methods to evaluate the degree of material degradation in fossile power plants.

• 한국분말재료학회지
• /
• 제19권3호
• /
• pp.215-219
• /
• 2012

An attempt was made to evaluate creep reliability of two commercial Ni-based superalloys by using ultrasonic wave. The materials include fine-grained PM alloy fabricated by mechanical alloying and subsequent hot isostatic pressing, and IN738LC cast alloy with a grain size of a few cm. Microstructural parameters (fraction of creep cavity and size of ${\gamma}^{\prime}$ precipitates) and ultrasonic parameters (velocity, attenuation) were measured to try to find relationships between them. Ultrasonic velocity decreased with creep cavity formation in PM alloy. On the other hand, no distinct changing trend of ultrasonic velocity was observed for IN738LC alloy. Ultrasonic attenuation was found to have a linear correlation with the size of ${\gamma}^{\prime}$ precipitates and was suggested as a potential parameter for monitoring creep reliability of IN738LC alloy.

• Journal of Welding and Joining
• /
• 제22권5호
• /
• pp.32-37
• /
• 2004

Application of bonding by adhesives can be found in many industries, particularly in advanced technological domains such as aeronautical and space, automobile and electronics industries. Periodic inspection with conventional ultrasonic NDE techniques is capable of indicating the presence and possible location of crack. Continuous ultrasonic attenuation monitoring has potential to supply information. This article discusses the use of pulse-echo ultrasonic testing for the inspection of adhesive bonds between metal sheets. The method is based on the measurement of the reflection coefficient at the metal/adhesive interface. By means of a control experiment it is shown that Quantitative Nondestructive Evaluation in Adhesive Joints are evaluated together with Ultrasonic Testing and Fracture Testing.

• 한국정밀공학회지
• /
• 제22권8호
• /
• pp.182-191
• /
• 2005

It is very important to obtain a high quality of bone image for an accurate ultrasonic measurement of bone mineral density. In this study, we suggested a technique to acquire an optimal image by adapting an acoustic lens and a properly selected ultrasonic probe. Also, we have applied an image processing algorithm with which automatically makes a decision of brightness and contrast of image by generating threshold level, a composition of ultrasonic data, an elimination of noise using modified median filter, and a real time interpolation. We could confirm much improved resolution of bone image with acoustic lens attached to the ultrasonic probe and with the image processing algorithm suggested in this study. Therefore, it became possible to precisely diagnose the osteoprosis using ultrasonic imaging technique.

• Journal of Biosystems Engineering
• /
• 제23권6호
• /
• pp.615-620
• /
• 1998

The nondestructive internal quality evaluation of agricultural products has been strongly required from the needs for individual inspection. In recent, ultrasonic wave has been considered as a solution for this problem. It transmit well through most materials and can handle safely and easily. However, specially in a watermelon, it is known that general frequency band (higher than 20kHz) ultrasonic waves do not transmitted well due to severe attenuation. The objectives of this study were to find out the proper waveform and frequency of the ultrasonic waves that transmit well inside the watermelon, and to analyze the transmitted waveform in order to make clear the structure of wave propagation in watermelon. The result of several experiments showed that 2kHz shear wave was the most suitable for the detection of internal cavity in the watermelon. Also, it was found that the surface wave did not influence the directly transmitted bulk wave. These results could be a basis of application of ultrasonic wave on the evaluation of internal quality of the watermelon.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1999년도 춘계학술발표회요약집
• /
• pp.124-124
• /
• 1999

An ultrasonic method is developed for the measurement of the two-phase mixture level in the reactor vessel or steam generator. The ultrasonic method is selected among the several non¬nuelear two-phase mixture level measurement methods through two steps of selection procedure. A commercial ultrasonic level measurement method is modified for application into the high temperature, pressure, and other conditions. The calculation method of the ultrasonic velocity is modified to consider the medium as the homogeneous mixture of air and steam. and to be applied into the high temperature and pressure conditions. The cross-correlation technique is adopted as a detection method to reduce the effects of the attenuation and the dif.JUsed reflection caused by suface fluctuation. The waveguides are developed to reduce the loss of echo and to remove the effects of obstructs. The present experimental study shows that the developed ultrasonic method measures the two-phase mixture level more accurately than the conventional methods do.

• 비파괴검사학회지
• /
• 제15권2호
• /
• pp.364-370
• /
• 1995

본 논문은 초음파법을 이용하여 소결 재료의 비파괴적인 평가 방법을 확립하는데 목적을 두고 있다. 소결 재료의 밀도는 소결체로 제작되는 동안 금형과 분말사이의 마찰 때문에 부분적으로 불균질한 분포를 가지고 있으며 이 불균질성은 에너지 감쇠 계수 및 초음파 반사 에코의 주파수 스펙트럼에 있어 중심 주파수의 변화량에 의해 조사되었다. 초음파의 속도, 탄성계수, 포와송 비는 소결 재료의 밀도와 비례 관계에 있었으며 저면 반사파의 중심 주파수는 초음파의 전파 거리의 증가 및 밀도의 감소에 따라 저주파수 쪽으로 이동하였으나 에너지 감쇠 계수는 밀도의 증가에 따라 감소하고 있었다. 본 논문에서는 반사파의 주파수 스펙트럼에 있어 중심 주파수의 변화가 소결 재료의 비파괴적인 평가 방법으로써의 가능성을 보여주고 있다.

• 대한방사선기술학회지:방사선기술과학
• /
• 제41권1호
• /
• pp.53-60
• /
• 2018

The purpose of this study was investigating the effect of 3D printing technology that changes the speed of sound (SOS) and the broadband ultrasound attenuation (BUA) by controlling the density of the media phantom. We used 3D printers which called additive manufacturing (AM) by using material with polylactic acid (PLA). The inside of the medium phantom was filled crossly with 100%, 90%, 80%, 70%, 60%, and 50% of the material. The ultrasonic instrument measured the SOS and the BUA using a 0.55 MHz ultrasound output in opposing mode with a pair of transducers. As a result, the density of the medium phantoms with the SOS showed very high correlation (r = 0.944), but the SOS showed very low correlation (r = 0.500). It is expecting that the manufacturing and measurement method of the medium phantom using 3D printing technology will be used as basic data for ultrasonic bone mineral density.

• 한국음향학회지
• /
• 제31권4호
• /
• pp.244-252
• /
• 2012

본 연구의 목적은 골절 위험도가 높은 대퇴골에서 음속 및 광대역 초음파 감쇠와 같은 음향특성과 골밀도 사이의 상관관계를 조사하는 것이다. 이를 위해 0.5 및 1.0 MHz의 중심주파수를 갖는 두 쌍의 초음파 트랜스듀서와 함께 투과법을 이용하여 생체 외 조건에서 15개의 소 대퇴골 해면질골 샘플의 음속 및 광대역 초음파 감쇠를 측정하였다. 또한 마이크로 컴퓨터 단층촬영법을 이용하여 해면질골 샘플의 단위체적당 골밀도를 측정하였다. 골밀도는 0.5 및 1.0 MHz 초음파 트랜스듀서를 이용하여 측정된 음속 및 광대역 초음파 감쇠와 모두 강한 상관관계를 나타냈으며, 골밀도와 0.5 MHz 초음파 트랜스듀서를 이용하여 측정된 광대역 초음파 감쇠 사이에 가장 높은 상관관계가 존재하였다. 이와 같은 결과는 생체 외 조건의 대퇴골에서 측정된 음향특성이 대퇴골의 골밀도를 예측하기에 충분한 지표라는 것을 의미한다.