• Journal of the Korean Ceramic Society
• /
• v.35 no.4
• /
• pp.325-332
• /
• 1998

Crystalline TiO2 ultrafine powders were prepared simply by heating and stirring aqueous TiOCl2 solution with {{{{ {Ti }^{4+ } }} concentration of 0.5 M from room temperature to 10$0^{\circ}C$ under 1 atmoshpere. The crystallinity and the particle shape of TiO2 ultrafine powders obtained by simple precipitation method were analyzed us-ing XRD(X-ray diffractometer). SEM(scanning electron microscopy) and TEM(transmission electron mi-croscopy) TiO2 crystalline precipitate with rutile phases is fully formed at the temperatures of up to $65^{\circ}C$ and then TiO2 crystalline precipitate with anatase phase starts to be formed above temperatures $65^{\circ}C$ showing its full formation at 10$0^{\circ}C$ These behaviors of TiO2 crystalline precipitate directly from an aqueous TiOCl2 solution would be caused due to the existence of {{{{ OMICRON ^2+ }} ions from distilled water which oxydize TiOCl2 to TiO2 not hydrolyzing it to Ti(OH)4 Here thermodynamically stable TiO2 rutile phase generally formed at higher temperature is practically precipitated at lower temperatures in this study This may be due to the precipitation by very slow reaction enough to make TiO2 particles allocated into stable rutile structure.

• Particle and aerosol research
• /
• v.14 no.3
• /
• pp.81-88
• /
• 2018

The market for improving the indoor air quality is continuously increasing, and air cleaners are the representative products. As interest in indoor air quality increases, so are the ultrafine particle which are harmful to the human body. Despite its many advantages, electrostatic precipitators are less used in indoor air due to ozone production. In this study, the carbon fiber sheet was applied to the discharge electrode and compared with the conventional tungsten wire discharge electrode. The particle collection efficiency and the amount of ozone generation were measured for 10-100 nm particles. Furthermore, it was applied to commercial air purifier with electrostatic precipitator to compare particle removal performance. The carbon fiber sheet type discharge electrode generates a small amount of ozone, and thus it can be applied to improve indoor air quality.

• Journal of the Korean Ceramic Society
• /
• v.24 no.1
• /
• pp.23-32
• /
• 1987

Synthesis of high purity ultrafine Si3N4 and ${\beta}$-Sialon powders was investigated via the simultaneous reduction and nitriding of amorphous SiO2, SiO2-Al2O3 system prepaerd by hydrolysis of alkoxides, using carbonablack as a reducing agent. In Si(OC2H5)4-C2H5 OH-H2 O-NH4OH system, hydrolysis rate increased with increasing reaction temperature and pH. Pure ${\alpha}$-Si3N4 was formed at 1350$^{\circ}C$ for 5 hrs in N2 atmosphere. In Si(OC2H5)4-Al(OC3H7)3-C6H6-H2 O-NH4OH system, weight loss increased as Si/Al ratio decreased. Single phase ${\beta}$-Sialon consisted of Si/Al=2 was formed at 1350$^{\circ}C$ in N2 and minor phases of ${\alpha}$-Si3N4, AIN, and X-phase were existed besides theSialon phase at other Si/Al ratios. The Si3N4 and Sialon powders synthesized from alkoxides consisted of uniform find particles of 0.05-0.2$\mu\textrm{m}$ in diameter, respectively.

• Toxicological Research
• /
• v.33 no.4
• /
• pp.305-313
• /
• 2017

Accumulating epidemiological evidence indicates that exposure to fine air pollution particles (APPs) is associated with a variety of adverse health effects. However, the exact physiochemical properties and biological toxicities of fine APPs are still not well characterized. We collected four types of fine particle (FP) (diesel exhaust particles [DEPs], natural organic combustion [NOC] ash, synthetic organic combustion [SOC] ash, and yellow sand dust [YSD]) and investigated their physicochemical properties and in vitro biological toxicity. DEPs were almost entirely composed of ultrafine particles (UFPs), while the NOC, SOC, and YSD particles were a mixture of UFPs and FPs. The main elements in the DEPs, NOC ash, SOC ash, and YSD were black carbon, silicon, black carbon, and silicon, respectively. DEPs exhibited dose-dependent mutagenicity even at a low dose in Salmonella typhimurium TA 98 and 100 strains in an Ames test for genotoxicity. However, NOC, SOC, and YSD particles did not show any mutagenicity at high doses. The neutral red uptake assay to test cell viability revealed that DEPs showed dose-dependent potent cytotoxicity even at a low concentration. The toxicity of DEPs was relatively higher than that of NOC, SOC, and YSD particles. Therefore, these results indicate that among the four FPs, DEPs showed the highest in vitro biological toxicity. Additional comprehensive research studies such as chemical analysis and in vivo acute and chronic inhalation toxicity tests are necessary to determine and clarify the effects of this air contaminant on human health.

• Journal of the Korean Ceramic Society
• /
• v.37 no.5
• /
• pp.473-478
• /
• 2000

The TiO2 powder with the values of the large specific surface area more than 150$m^2$/g has been prepared with the homogeneous precipitation process below 5$0^{\circ}C$ and its formation mechanism was investigated using the SEM, TEM and Raman Spectroscopy. With the spontaneous hydrolysis of aqueous TiOCl2 solutions, all the precipitates were fully and homogeneously crystallized with the rutile TiO2 phase simply by heating, which as transformed to the anatase TiO2 phase as increasing the addition of SO42- ions to the aqueous TiOCl2 solution. The precipitates were formed with spherical secondary particles which consisted of acicular, spherical and mixed primary particles corresponding to the rutile, anatase and mixed phases, respectively. It can be thought that the formation and phase determination of crystalline TiO2 powders even at ambient temperature would be related with the existence of the capillary force. This force might be varied depending on the shape change of the primary particles.

• Food Science and Biotechnology
• /
• v.18 no.6
• /
• pp.1439-1446
• /
• 2009

The surfaces of different-sized endosperm, bran, and husk rice powders were modified using carboxymethylation. Carboxymethylation was carried out using aqueous alkalization and neutralization. After the carboxymethylation process, the centrifuged products were milled and classified by size: particles passed through sieves of 45, 106, and $300-{\mu}m$ width. The effect of carboxymethylation on physical properties such as solubility and dispersibility of endosperm, bran, and husk particles were studied. Overall, carboxymethylation increased solubility of the particles, while size reduction increased dispersibility. In particular, carboxymethylation created good aqueous suspensions by minimizing interparticle agglomeration. Our results show that the combination of size reduction and carboxymethylation improves solubility and dispersibility, resulting in better stability of the suspension. This study may be helpful for expanding the use of rice and its byproducts as ingredients in a variety of food and beverage applications.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.5
• /
• pp.657-665
• /
• 1999

Particulate matter produced by diesel engines is of concern to cngine manufactures because of its environmental impact. The majority of diesel particles are in the range of smaller than 1 ${\mu}{\textrm}{m}$. Because of their tiny volume, ultrafine diesel particles contribute very little to the total mass concentration which is currently regulated for automobile emissions. Ultrafinc particles are known to have deleterious effects upon human health cspecially because they penetrate deeply human respiratory tract and have negative effects on the health. In this study, the engine exhaust gas was diluted in a dilution tunnel and the particle size distribution was measured using the scanning mobility particel sizer system. Measurements of the number and the mass concentrations of the diesel exhaust were made under different engine ooperating conditions. The dilution sampling system provided a common basis for collection of the exhaust by cooling and diluting the source emission prior to the measurement. The measurement results showed that the particle size distributions of the exhaust from the diesel vehicles equipment with either heavy-duty or lignt-duty diesel engines, were similar in the particle size range of 0.08~0.2${\mu}{\textrm}{m}$.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.10
• /
• pp.717-723
• /
• 2013

The Korea Ministry of Environment prepares some paticulate matter eliminate measures for national health protection, as the Paticulate Matter ($PM_{2.5}$) exceeds the standard at more than half of the monitoring posts installed in the nation's big cities. At the center of JeonJu, when measuring the ultrafine particles of inner car at the different driving conditions, at the condition of the Actuator of inner recirculation mode and the Blower of 2-speed, the reduction speed of the ultrafine particles is most fast and the concentration stays low. When the windows are opened during driving, outer pollutants enter the car and also inner paticulate matter flies in all direction, and the increase of passengers causes the scattering of the ultrafine paticles. As the filter for air cleaning, the using of polypropylene non-woven fabric (used commonly now) is most excellent, but for the removal of volatile organic substance as well as the paticulate matter, it is thought that the using of activated carbon fiber filter, carbon adsorbent, is even more excellent.

• Journal of Environmental Health Sciences
• /
• v.44 no.6
• /
• pp.524-538
• /
• 2018

Objective: This study aimed to identify the size distributions of particulate matter emitted during 3D printing according to operational conditions and estimate particle inhalation exposure doses at each respiratory region. Methods: Four types of printing filaments were selected: acrylonitrile-butadiene-styrene (ABS), polylactic acid (PLA), Laywood, and nylon. A fused deposition modeling (FDM) 3D printer was used for printing. Airborne particles between 10 nm and $10{\mu}m$ were measured before, during, and after printing using real-time monitors under extruder temperatures from 215 to $290^{\circ}C$. Inhalation exposures, including inhaled and deposited doses at the respiratory regions, were estimated using a mathematical model. Results: Nanoparticles dominated among the particles emitted during printing, and more particles were emitted with higher temperatures for all materials. Under all temperature conditions, the Laywood emitted the highest particle concentration, followed by ABS, PLA, and nylon. The particle concentration peaked for the initial 10 to 20 minutes after starting operations and gradually decreased with elapsed time. Nanoparticles accounted for a large proportion of the total inhaled particles in terms of number, and about a half of the inhaled nanoparticles were estimated to be deposited in the alveolar region. In the case of the mass of inhaled and deposited dose, particles between 0.1 and $1.0{\mu}m$ made up a large proportion. Conclusion: The number of consumers using 3D printers is expected to expand, but hazardous emissions such as thermal byproducts from 3D printing are still unclear. Further studies should be conducted and appropriate control strategies considered in order to minimize human exposure.

• Transactions on Electrical and Electronic Materials
• /
• v.14 no.3
• /
• pp.121-124
• /
• 2013

The incorporation of 90 nm alumina particles into an epoxy matrix to form a composite microstructure is described in present study. It is shown that the use of ultrafine particles results in a substantial change in the behavior of the composite, which can be traced to the mitigation of internal charges when a comparison is made with conventional $Al_2O_3$ fillers. A variety of diagnostic techniques have been used to augment pulsed electro-acoustic space charge measurement to provide a basis for understanding the underlying physics of the phenomenon. It would appear that, when the size of the inclusions becomes small enough, they act cooperatively with the host structure and cease to exhibit interfacial properties. It is postulated that the $Al_2O_3$ particles are surrounded by high charge concentrations. Since $Al_2O_3$ particles have very high specific areas, these regions allow limited charge percolation through $Al_2O_3$ filled dielectrics. The practical consequences of this have also been explored in terms of the electric strength exhibited. It would appear that there was a window in which real advantages accumulated from the nano-formulated material. An optimum filler loading of about 0.5 wt.% was indicated.