• 한국응용과학기술학회지
• /
• 제26권1호
• /
• pp.102-108
• /
• 2009

Behaviors of saturated fatty acid halides (CI4, C16, C18) were measured by LB method when the molecules were stimulated by pressure. The saturated fatty acid halides were deposited on the indium tin oxide(lTO) glass by the LB method. The average organic ultra thin film size and the surface roughness of the fatty acid halides thin films were investigated using AFM. It was found that AFM images show small surface roughness ($2.5{\sim}5.0\;nm$) and the organic ultra thin film size of $2.5{\sim}12\;nm$. Both aggregations and pin-holes were also seen on the AFM images. However we found that the surface roughness. These effects seem to be reasonable to be related to the increase of the organic ultra thin film size of fatty acid halides.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 하계학술대회 논문집
• /
• pp.877-880
• /
• 2000

The length extensional vibration mode of a piezoelectric ceramic substrate is used in fabricating the ultra-small size resonators and filters. In general, the three side ratios of the substrate effect the resonant characteristics of the resonator using its length extensional vibration. In this paper, their relationships are studied. We know that changing the ratio of its length to its width makes possible to change the resonant frequency of the width vibration without degrading the length extensional vibration.

• 전기학회논문지P
• /
• 제58권1호
• /
• pp.33-37
• /
• 2009

In this paper, a printed small Ultra-Wideband (UWB) antenna with directive radiation characteristics based on combination of electric-magnetic radiators is presented. The combinations of the electric and magnetic type antennas result in the directive radiation patterns for all observed UWB frequency band. Simple combination of dipole antenna and loop antenna is also presented to show that proper configuration of electric radiator and magnetic radiator can produces directive radiation characteristics. The target frequency is from 3.1 GHz to 10.6 GHz with size of $15\;mm{\times}31\;mm$. A proto-type of the combined antenna is simulated, fabricated and measured. Simulation and experimental results of input impedance and gain characteristics of the proposed antenna are presented. There are good agreements between the simulated and measured VSWR curves. Also, the results show the directive radiation characteristics with small antenna form factor over the target frequency range.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part 1
• /
• pp.39-40
• /
• 2006

The relationship between the powder particle size change and a mechanical property of the Metal Injection Molding (MIM) product was examined in detail. The XRD results indicate that the diffraction peaks of BCC appeared in compacts of powder particle size of 4 to $10{\mu}m$ as well as the bulk SUS630. However, the diffraction peaks from both BCC and FCC were observed in the compact with powder size less than $3{\mu}m$. TEM observation revealed that the powder with those BCC/FCC two phase structure have a finely dispersed $SiO_2$ precipitates. Because the Si is ferrite stabilizing element, decrease of Si composition in the matrix phase by the $SiO_2$ precipitation resulted in formation of the retained austenite. Therefore, controlling the elements such as Si as well as oxygen decrease is very important to obtain a normal microstructure in ultra-fine powder $(<3{\mu}m)$ injection molding.

• 한국위성정보통신학회논문지
• /
• 제10권2호
• /
• pp.70-74
• /
• 2015

본 논문은 위성통신 기반의 위성 영상감시 센서 네트워크 적용을 위한 스마트 비젼 센서에 대해 기술한다. 스마트 비젼센서 단말은 현장에서 산불, 연기, 침입자 움직임 등의 이벤트를 자동감지하면서 높은 성능 신뢰도, 견고한 하드웨어 내구성, 용이한 유지보수, 끊김없는 통신유지 기능들이 요구된다. 이러한 요구사항들을 만족시키기 위하여 스마트 비젼 센서가 내장된 초소형 위성통신 단말을 제안하며 위성 송수신 기능과 더불어 고 신뢰도의 임베디드 영상분석 및 영상압축 기능을 처리한다. 제안하는 비젼 센서 알고리즘의 컴퓨터 시뮬레이션과 비젼 센서 시제품 시험을 통하여 영상감시 성능을 검증하였으며 실용성을 확인하였다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.769-770
• /
• 2006

The MIM industry is currently focusing on parts that are used in automobiles and medical instruments. Many of the parts in these categories are very small and often not easy to machine because of its complex geometry. Therefore MIM is well suited for the production of these parts. We tested the sinterability of SUS316L ultra fine powders (3,4, 6, 8micron) produced by ATMIX high-pressure water-atomization, and it showed excellent results. A density of 97% theoretical was obtained by sintering at 1373K when using the ultra fine powder (3micron). Specifically, the finer the powder size, higher was the sintered density. The surface roughness and accuracy are also greatly improved with ATMIX ultra fine powder.

• 한국결정성장학회지
• /
• 제15권6호
• /
• pp.239-243
• /
• 2005

The effect of pH and particle size on the dispersion stability of ultra-fine $BaTiO_3$ suspensions in aqueous medium have been investigated by means of zeta potential, sediment experiments, and powder properties (particle analysis, specific surface area) etc. Zeta potential as a function of pH for two particles of different size increases from -75 to +10 mV with decreasing pH from 8.5 to 1.4. The curve of zeta potential for small particle (150 nm) has slow slope than that of large particle (900nm), giving IEP (isoelectric point) value of pH=1.6 for small particle and pH=1.9 for large particle respectively, which means that it is more difficult to control zeta potential with pH fur small particle than large particle. The dispersion stability of $BaTiO_3$ particles in aqueous medium was found to be strongly related with the agglomeration of colloidal suspensions with time through the sedimentation behaviors of colloidal particles with time and pH value.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.186-186
• /
• 2012

This report investigates a new synthetic route and the size-dependent optical and electrical properties of PbS nanocrystal quantum dots (NQDs) in diameters ranging between 1.5 and 6 nm. Particularly we synthesize ultra-small sized PbS NQDs having extreme quantum confinement with 1.5~2.9 nm in diameter (2.58~1.5 eV in first exciton energy) for the first time by adjusting growth temperature and growth time. In this region, the Stokes shift increases as decreasing size, which is testimony to the highly quantum confinement effect of ultra-small sized PbS NQDs. To find out the electrical properties, we fabricate self-assembled films of PbS NQDs using layer by layer (LBL) spin-coating method and replacing the original ligands with oleic acid to short ligands with 1, 2-ethandithiol (EDT) in the course. The use of capping ligands (EDT) allows us to achieve effective electrical transport in the arrays of solution processed PbS NQDs. These high-quality films apply to Schottky solar cell made in an glass/ITO/PbS/LiF/Al structure and thin-film transistor varying the PbS NQDs diameter 1.5~6 nm. We achieve the highest open-circuit voltage (＜0.6 V) in Schottky solar cell ever using PbS NQDs with first exciton energy 2.58 eV.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1444-1446
• /
• 2005

Recently most machineries have been small size and mobile type. And human body insertion type endoscope and micro robot technology has been developed. Then the motors used in this field are developed in micro size such as about 2mm in diameter. The structure of this motor is similar to a general brushless DC(BLDC) motor but because of small size there is no position sensor such as hall sensor. In this paper, a design and fabrication result of an ultra-small brushless DC motor is presented. This motor is designed to 3-phase coreless winding and operated with sensor-less type driver. Test results confirmed the feasibility of the proposed motor drive system design.

• Journal of Welding and Joining
• /
• 제21권3호
• /
• pp.85-91
• /
• 2003

Narrow gap welding has many advantages over conventional V-grooved butt welding such as high productivity, small deformation and improved mechanical property of joints. With narrower groove gap, less arc heat input is expected will all the other advantages of narrow gap welding. The main defects of narrow gap welding include the lack of root fusion, convex bead surface and irregular surface, all of which have negative effects on the next welding pass. This paper suggests an up-and-down torch oscillation for ultra narrow gap welding with gap size of 5mm and investigates the proper welding conditions to fulfill the reliable and high welding quality. First, GMA welding model was suggested for ultra narrow gap welding system with Halmoy's model referenced for wire melting modeling. And the arc length in ultra narrow gap was defined. Secondly, based on the experimental results of up-and-down torch oscillation welding, phase shift of current and wire extension length were simulated for varying oscillation frequency to show that weld the bead shape in ultra narrow gap welding can be predicted. As the result, it was confirmed that reliable weld quality in ultra narrow gap welding can be achieved with up-and-down torch oscillation above 15Hz due to its ability to provide uniform heat input along the sidewall of gap.