• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.6
• /
• pp.128-138
• /
• 2022

In this study, in order to apply ultra-high-strength concrete beams of 100 MPa or more manufactured by centrifugal molding as the superstructure of the avalanche tunnel, the purpose is to verify the structural safety of the corner rigid joint in which the centrifugal molded beam is integrated with the substructure, which is the negative moment area. A full-size specimen was manufactured, and loading tests and analysis studies were performed. In order to expect the same effect that the maximum moment occurs in the corner joint part of the upper slab end when the standard model of the avalanche tunnel is designed with a load combination according to the specification, a modified cantilever type structural model specimen was manufactured and the corner rigid joint was fixedly connected. A study was performed to determine the performance of the method and the optimal connection construction method. The test results demonstrated that the proposed connection system outperforms others. Despite having differences in joint connection construction type, stable flexural behavior was shown in all the tested specimens. The proposed method also outperformed the behavior of centrifugally formed beams and upper slabs. The behavior of the corner rigid joint analysis model according to the F.E. analysis showed slightly greater stiffness compared to the results of the experiment, but the overall behavior was almost similar. Therefore, there is no structural problem in the construction of the corner rigid joint between the centrifugally formed beam and the wall developed in this study.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.4
• /
• pp.728-732
• /
• 2010

GIS(Gas insulated switching gear) is power equipment with excellent dielectric strength and is economy merit in high confidence and stability. Recently, because equipment of GIS was occurring problem of confidence used for a long time, partial discharge on-line diagnosis systems have been importantly recognized. Partial discharge (PD) detection is an effective means for monitoring and evaluation of dielectric condition of gas insulated system (GIS). The ultra-high-frequency (UHF) PD detection technique can detect and locate the PD sources inside GIS by detecting electromagnetic wave emitted from PD source. Therefore, real-time diagnostic system using UHF detection method has been developed for this application is being expanded gradually. However, the signal of partial discharge occurring in SF6 gas is very weak and susceptible to external noises which mainly consist of PD in air. Thus, it is important to distinguish the PD in SF6 gas more sensitively from the external noises. Unfortunately, these external noise signals and the partial discharge signals have very similar characteristics. Therefore, to solve this problem, we need the signal processing method for distinguish partial discharge signals with external noise signals for improvement of SNR(signal to noise ratio) and sensitivity. In this paper, we proposed internal signal processing method for removing external noise signals with built-in pre.amplifier and frequency conversion circuit.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1975-1979
• /
• 2005

Equal channel angular pressing has been employed to produce materials with ultra-fine grains that have high strength and high corrosion resistance properties. Along with the experiments, the finite element method has been widely performed to investigate the deformation behavior of specimen and the effects of process parameters of ECAP. In general, several steps of ECAP have been repeatedly executed. In this paper, the effects of sectional shape change have been investigated during ECMAP (RouteA, RouteC) with pure-Zr by using three-dimensional finite element analysis. The results have been compared with the experimental results.

• Laser Solutions
• /
• v.17 no.4
• /
• pp.14-19
• /
• 2014

Laser beam was applied on the boundary of the polyurethane and biodegradable polyacetate polymers. The distributed laser passed through the polyurethane layer and heated the polyacetate layer, then the soften acetate was squeezed thorough the 1mm square slots of polyurethane for the mechanical joining. The surface roughness ranging between $0.28{\mu}m$ and $3.06{\mu}m$ had almost no effect on joining strength, but the optical properties of HD (High Definition) and UHD (Ultra High Definition) mode affected laser beam transmittance. The optimum laser power was found to be between 8watt and 10watt with 500mm/min of scanning speed. The joining boundary was characterized by optical and SEM analysis. Based on the experiment and characterization results, the laser energy was effective for the polymer joining and efficiency of joining.

• Journal of Power System Engineering
• /
• v.17 no.2
• /
• pp.114-120
• /
• 2013

This study was carried out to investigate the relationship between mechanical properties and damping capacity in high manganese austenitic stainless steel with two phase mixed structure of reversed austenite and deformation induced martensite. Reversed austenite of ultra-fine grain size less than $0.3{\mu}m$ was obtained by reversion treatment. Two phase structure of deformation induced martensite and reversed austenite was obtained by annealing treatment at range of $500^{\circ}C{\sim}700^{\circ}C$ for various time in cold rolled high manganese austenite stainless steel. In stainless steel with two phase mixed structure of martensite and austenite, damping capacity decreased rapidly with the increasing hardness and strength. With the increasing elongation, damping capacity was increased rapidly and then, slowly increased.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.4
• /
• pp.279-290
• /
• 2013

In this paper, we propose a transmission scheme of MAC protocol that enables secure voice communications by exploiting the wide spectrum and low signal strength characteristics of the ultra wide band technology. In addition, it also supports high level of terminal mobility by deploying mobile ad hoc network schemes. While most of existing UWB MAC protocols are operated as a synchronous mode, the proposed scheme operates in an asynchronous mode for supporting high mobility and sends voice packets without RTS/CTS control packets for efficient voice traffic transmission without retransmission. With simulation program, we prove that the proposed scheme satisfies the required voice quality and packet delivery time.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.854-860
• /
• 2004

"Research and Development of Melt-Growth Composite (MGC) Ultra High Efficiency Gas Turbine System Technology" program has been started in JFY2001. The main objective of the program is to establish basic component technologies to apply MGC material to an efficient gas turbine system successfully. It is known that MGC material maintains its mechanical strength at room temperature up to about 2000 K, which is ideal for the high temperature gas turbine. The purposes of the present study are to develop the cooling structure of the gas turbine combustor liner where MGC material is applied as the heat shield panel, also to develop the low NOx combustion system for a 1970 K (1700 deg.C) class gas turbine combustor. To start with, basic heat transfer characteristics were investigated by one-dimensional calculation and heat transfer experiment for the cooling structure. Axially staged configuration and fuel preparation were investigated by CFD calculation and experiments for the low NOx combustor.

• Steel and Composite Structures
• /
• v.48 no.5
• /
• pp.531-545
• /
• 2023

Composite dowels are implemented as a powerful alternative to headed studs for the efficient combination of Ultra High-Performance Concrete (UHPC) with high-strength steel in novel composite structures. They are required to provide sufficient shear resistance and ensure the transmission of tensile forces in the composite connection in order to prevent lifting of the concrete slab. In this paper, the load bearing capacity of puzzle-shaped and clothoidal-shaped dowels encased in UHPC specimen were investigated based on validated experimental test data. Considering the influence of the embedment depth and the spacing width of shear dowels, the characteristics of UHPC square plate on the load bearing capacity of composite structure, 240 numeric models have been constructed and analyzed. Three artificial intelligence approaches have been implemented to learn the discipline from collected experimental data and then make prediction, which includes Artificial Neural Network-Particle Swarm Optimization (ANN-PSO), Adaptive Neuro-Fuzzy Inference System (ANFIS) and an Extreme Learning Machine (ELM). Among the factors, the embedment depth of composite dowel is proved to be the most influential parameter on the load bearing capacity. Furthermore, the results of the prediction models reveal that ELM is capable to achieve more accurate prediction.

• Composites Research
• /
• v.22 no.6
• /
• pp.52-62
• /
• 2009

This paper is for the state of the art of the lightweight protective clothing against the mine, and it covers the preliminary work focused on the appropriate protection, ballistics, convenience, and wearability. It is suggested that the lightweight protective clothing should be fabricated with the laminated materials of high strength woven and non-woven fabrics to reduce the weight and thickness, thus improving the wearability. And partial reinforcement of the protective clothing is necessary to prevent the mortal wound near the important parts of the body without disturbing the arbitrary activity. The composition of the protective clothing should be designed in consideration of easy putting-on and taking-off in addition to easy divesture, which require little motion of the body is in case of serious injury. Additionally, status of the practical technique for high performance and ultra-light hybrid armor material were also described.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.178-184
• /
• 2015

This paper proposes a hardware architecture for high performance Deblocking filter(DBF) in High Efficiency Video Coding for UHD(Ultra High Definition) videos. This proposed hardware architecture which has less processing time has a 4-stage pipelined architecture with two filters and parallel boundary strength module. Also, the proposed filter can be used in low-voltage design by using clock gating architecture in 4-stage pipeline. The segmented memory architecture solves the hazard issue that arises when single port SRAM is accessed. The proposed order of filtering shortens the delay time that arises when storing data into the single port SRAM at the pre-processing stage. The DBF hardware proposed in this paper was designed with Verilog HDL, and was implemented with 22k logic gates as a result of synthesis using TSMC 0.18um CMOS standard cell library. Furthermore, the dynamic frequency can process UHD 8k($7680{\times}4320$) samples@60fps using a frequency of 150MHz with an 8K resolution and maximum dynamic frequency is 285MHz. Result from analysis shows that the proposed DBF hardware architecture operation cycle for one process coding unit has improved by 32% over the previous one.