• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.202-203
• /
• 2002

Ribbon type nanocrystalline alloy cores have shown excellent soft magnetic properties in the high frequency range because of small crystalline anisotropy and nearly zero magnetostriction[1]. In present, however ribbon alloys gives some limit in applications such as a large inductor and reactors of PFC circuit, which are required good DC bias property and low loss in the high frequency. Powder alloys with ultra fine grain structure can be an important way to overcome this kind of disadvantage, and to improve the high frequency soft magnetic properties in conventional metallic powder cores[2]. (omitted)

• Computers and Concrete
• /
• v.21 no.2
• /
• pp.167-179
• /
• 2018

Reactive powder concrete (RPC) is a type of ultra-high strength cement-based material with a dense microstructure, which is made of ultra-fine powders. RPC demonstrate a very brittle behavior, thus adding fibers improves its mechanical properties. In this study, it was attempted to investigate the effect of using steel and polyvinyl alcohol (PVA) fibers as well as their combination on the properties of RPC. In this regard, hooked-end crimped steel fibers together with short PVA fibers were utilized. Steel and PVA fibers were used with the maximum volume fraction of 3% and 0.75%, respectively, and also different combinations of these fibers were used with the maximum volume fraction of 1% in the concrete mixes. In total, 107 concrete specimens were prepared, and the effect of fiber type and volume fraction on the physico-mechanical properties of RPC including compressive strength, tensile strength, modulus of elasticity, density, and failure mode was explored. In addition, the effect of the curing type on the properties of compressive strength, modulus of elasticity, and density of RPC was evaluated. Finally, coefficients for conversion of cubic compressive strength to cylindrical one for the RPC specimens were obtained under the two curing regimes of heat treatment and standard water curing.

• Journal of Powder Materials
• /
• v.16 no.5
• /
• pp.310-315
• /
• 2009

Ultra-fine TiC/Co composite powder was synthesized by the carbothermal reduction process without wet chemical processing. The starting powder was prepared by milling of titanium dioxide and cobalt oxalate powders followed by subsequent calcination to have a target composition of TiC-15 wt.%Co. The prepared oxide powder was mixed again with carbon black, and this mixture was then heat-treated under flowing argon atmosphere. The changes in the phase, mass and particle size of the mixture during heat treatment were investigated using XRD, TG-DTA and SEM. The synthesized oxide powder after heat treatment at 700$^{\circ}C$ has a mixed phase of TiO$_2$ and CoTiO$_3$ phases. This composite oxide powder was carbothermally reduced to TiC/Co composite powder by the solid carbon. The synthesized TiC/Co composite powder at 1300$^{\circ}C$ for 9 hours has particle size of under about 0.4 $\mu$m.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.11a
• /
• pp.68-71
• /
• 2013

Reactive Powder Concrete (RPC) is an ultra high strength and high ductility cement-based composite material and has shown some promise as a new generation concrete in construction field. It is characterized by a silica fume-cement mixture with very low water-binder (w/b) ratio and very dense microstructure, which is formed using various powders such as cement, silica fume and very fine quartz sand (0.15~0.4mm) instead of ordinary coarse aggregate. However, the unit weight of cement in RPC is as high as 900~1,000 kg/㎥ due to the use of very fine sand instead of coarse aggregate, and a large volume of relatively expensive silica fume as a high reactivity pozzolan is also used, which is not produced in Korea and thus must be imported. Since the density of RPC has a heavy weight at 2.5~3.0 g/㎤. In this study, the modified RPC was made by the combination of ternary pozzolanic materials such as blast furnace slag and fly ash, silica fume in order to economically and practically feasible for Korea's situation. The fire resistance and structural behavior of the modified RPC exposed to high temperature were investigated.

• Analytical Science and Technology
• /
• v.26 no.4
• /
• pp.256-261
• /
• 2013

The efficiency of the two extractions (refluxing extraction and heating-block extraction) was compared to develop the simple analytical method for the determination of capsaicinoids, including capsaicin and dihydrocapsaicin in red pepper powder. For the method development, the parameters, including particle size, extraction time and sample size, were evaluated using ultra high performance liquid chromatography (u-HPLC). It was found that the most effective extraction time of the refluxing extraction was 3 hr. The higher extraction efficiency was obtained with the fine particle of a mild red pepper powder, while the particle size did not affect the extraction efficiency in case of the hot red pepper powder. The higher extraction efficiency was obtained with the small size of sample taken because of the ratio of the large extracting solvent to sample amount. The extraction efficiency of the refluxing method was 3-9% higher than that of the heating-block method, however, the heating-block method could be applied to the determination of capsaicinoids in the red pepper powder for the purpose of quality control of the product.

• Journal of environmental and Sanitary engineering
• /
• v.11 no.1
• /
• pp.63-70
• /
• 1996

The synthesis of high purity and ultra-fine $BaTiO_3$ by precipitation with gaseous $NH_3$ as precipitator was investigated to find an alternative process to solve various problems of recent wet methods. A synthesis process for $BaTiO_3$ powder using $NH_3$ gas as a precipitator in a bubble column reactor was experimentally successful in developing the production process of piezoelectric ceramic $BaTiO_3$ powder. And a 2.33m1/sec is approprite for the feed flow rate, $BaTiO_3$ powder produced under above the condition is spherical type, its particle size was about $0.2{\mu}m$.

• Journal of the Korean Ceramic Society
• /
• v.33 no.11
• /
• pp.1276-1284
• /
• 1996

Ultrafine calcim carbonate powders with the size of 0.05~0.1 ${\mu}{\textrm}{m}$ and the calcite phase were prepared by the nozzle spouting method which was conducted by spouting calcium hydroxide slurry in reactor filled with CO2 gas. Well dispersed ultra-fine particles were synthesized in condition of high Ca(OH)2 concentration of the slurry ( 0.5wt%) synthesized calcium carbonate powder was shown the large particle size with agglo-meration.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2005.11a
• /
• pp.87-88
• /
• 2005

Ultra-fine copper powders with particle size about 150 nm were synthesized from copper hydroxide slurry by wet method using hydrazine as reduction agent and several sur factants at below $80^{\circ}C$. The particle size distribution and dispersion of synthesized powders as function of temperature, feeding rate of reduction and especially, sur factants were character ized by XRD, BET, PSA and SEM by this process.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.967-968
• /
• 2006

This research reports for the successful consolidation of $Al_2O_3$ powder with retained ultra-fine structure using MPC and sintering. Measurements in the consolidated $Al_2O_3$ bulk indicated that hardness, fracture toughenss, and breakdown voltage have been much improved relative to the conventional polycrystalline materials. Finally, optimization of the compaction parameters and sintering conditions will lead to the consolidation of $Al_2O_3$ nanopowder with higher density and even further enhanced mechanical properties.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.36-37
• /
• 2006

This study aims to investigate the usage of nano-scale particles in a micro metal injection molding ($\mu$-MIM) process. Nanoscale particle is effective to improve transcription and surface roughness in small structure. Moreover, the effects of hybrid micro/nano particles, Cu/Cu and SUS/Cu were investigated. Small dumbbell specimens were produced using various feedstocks prepared by changing binder content and fraction of nano-scale Cu particle (0.3 and $0.13{\mu}m$ in particle size). The effects of adding the fraction of nano-scale Cu powder on the melt viscosity of the feedstock, microstructure, density and tensile strength of sintered parts were discussed.