• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.961-963
• /
• 2015

In this study, we studied the effect of $Co^{60}$ gamma-radiation on the fiber Bragg gratings written by femtosecond UV laser in single mode optical fibers. The fiber Bragg gratings were exposed to gamma-radiation up to a dose of about 31.6 kGy at the dose rate of 106 Gy/min. According to the experimental data and analysis results, we confirmed Bragg gratings written by femtosecond laser have the excellent radiation-hardened characteristics for high radiation environments.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.5
• /
• pp.419-424
• /
• 2009

ZnO films doped with different contents of indium ($0.1{\sim}10$ at.%) were deposited on Si (111) substrate by Pulsed Laser Deposition (PLD). The structural, electrical and optical properties of the films were investigated using XRD, AFM, Hall and PL measurement. Results showed that un-doped ZnO film had (002) plane as the c-axis orientated growth, whereas indium doped ZnO films exhibited the peak of (002) and the weak (101) plane. In addition, in the indium doped ZnO films, the electron concentration is ten times higher than that of un-doped ZnO film, while the resistivity is ten times lower than that of un-doped ZnO film. The indium doped ZnO films have UV emission about 380 nm and show a red shift with increasing contents of indium. The I-V curve of the fabricated diode show the typical diode characteristics and have the turn on voltage of about 2 V.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.3 no.2
• /
• pp.23-31
• /
• 1997

The results of high speed photography, acoustic emission detection and plasma UV radiation intensity measurement during CO2 laser welding of stainless steel 304 are presented. Video images with high spatial and temporal resolution allowed to observe the melt dynamics and keyhole evolution. The existence of a high speed melt flow which originated from the part of weld pool and flowed along the sides wall of keyhole was confirmed by the slag motion on the weld pool. the characteristic frequencies of flow instability and keyhole fluctuations at different welding speed were measured and compared with the results of Fourier analyses of temporal acoustic emission (AE) and light emission (LE) spectra. The experimental results were compared with the newly developed numerical model of keyhole dynamics. (The model is based on the assumption that the propagation of front part of keyhole into material is due to the melt ejection driven by laser induced surface evaporation.) The calculations predict that a high speed melt flow is induced at the front part of keyhole when the sample travel speed exceeds several 10mm/s. The numerical analysis also shows the hump formation on the front keyhole wall surface. Experimentally observed melt behavior and transformation of the AE and LE spectra with variation of welding speed are qualitatively in good agreement with the model predictions.

• Bulletin of the Korean Chemical Society
• /
• v.21 no.6
• /
• pp.583-587
• /
• 2000

Depletion kinetics of ground state FeO molecules by $0_2$, $N_2O$ and $N_2$ has been studied at room temperature. The ground state FeO molecules were generated by photolysis of a $Fe$(CO)_5$/M(O_2$, $N_2O)/He$ mixture using an unfocused weak UV laser beam. The formation of ground state FeO molecules was identified by a laser-induced fluorescence (LIF) method. The intensity distribution of those undisturbed rotational lines suggests that the rotational temperature of the ground state FeO molecules is lower than room temperature. The LIF intensities of FeO molecules at different partial pressures of $0_2$, $N_2O$ and $N_2$ were monitored as a function of the time delay between the photolysis and probe laser pulses to obtain the depletion rate constants for the ground state FeO. They were 1.7+ 0.2x $10^{-12}$, 4.8 $\pm0.4$ x $10^{-12}$, and $1.4\pm$ 0.2x $10^{-12}cm^3$molecule^{-1}s^{-1}$$ by $0_2$, $N_20$, and $N_2$, respectively.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.2
• /
• pp.625-628
• /
• 2012

We investigated the interaction between polyynes (linear carbon chains) and various metal nanoparticles (Ag, Au, and Cu) to provide insight into the optical properties of metal-polyynes systems prepared by different experimental techniques. Polyynes were produced by laser ablation in deionized water, metal nanoparticles solutions, and copper chloride solution. Metal nanoparticles complexes with polyynes were analyzed by Raman, surface-enhanced Raman scattering, and UV-vis spectroscopy.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06a
• /
• pp.462-487
• /
• 1996

We report on the fourth and fifth harmonics generations of Nd:YAG laser radiation realized in CsLiB6O10(CLBO). The values of 500 mJ and 230 mJ at 266 nm and 213 nm were obtained from 2200 mJ of fundamental energy. Doping of CLBO has been carried out and the Al doping was found to give rise to an enhancement of mechanical and chemical properties.

• Proceedings of the Optical Society of Korea Conference
• /
• 1991.06a
• /
• pp.81-87
• /
• 1991

A design of a four-mirror optical system for submicron lithography using KrF excimer laser beam(λ=248nm) is presented. By using the third order aberration theory, analytic solutions for a telecentric, flat-field, and anastigmatic four-spherical-mirror system (reduction magnification 5$\times$) are found. Aspherization is carried out to the spherical mirror surfaces in order to reduce the residual higher order aberrations and vignetting effect. Finally we obtain a reflection system useful in submicron lithographic application.

• Transactions of Materials Processing
• /
• v.13 no.3
• /
• pp.205-210
• /
• 2004

The waveguide Bragg gratings have been fabricated by the phase-mask method. An excimer laser with maximum 600mJ output pulse energy and uniform phase masks have been used. Hydrogen loading is often used for enhancing the uv photosensitivity of the core, however, the resultant gratings show significant aging effect. In the present study, high temperature thermal annealing process has been investigated to obtain thermal gratings and process parameters are deduced.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.08a
• /
• pp.108-109
• /
• 2000

현재 많은 종류의 레이저가 학술적으로나 산업계에서 다양하게 사용되고 있다. 그리고 그 중에서도 자외선 레이저의 필요성이 한층 강조되고 있는 시점이다. 사용되고 있는 자외선 레이저는 Eximer 레이저, Nd:YAG의 제3고조파, 다른 레이저로 펌핑한 색소 레이저등이 그 주류를 이루고 있다. 하지만 이들 레이저들은 값이 아주 고가이거나 그 출력이 매우 낮아 새로운 방식의 레이저를 요구하고 있다. 그래서 본 실험실에서는 여러 용도로 사용 가능한 펄스형 고출력 색소 레이저를 개발하고 있다. (중략)

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.10
• /
• pp.831-835
• /
• 2014

The relative concentration of surface and interfacial defects in hydrothermally grown ZnO nanostructures was investigated by a comparison of two samples having different growth temperatures via bias voltage sweep rate under laser illumination of 405 and 355 nm. The current of small ZnO nanostructures (growth temperature of $75^{\circ}C$) decreased when induced more slowly bias voltage sweep rate under the laser illumination. In contrast, the current of large ZnO nanostructures (growth temperature of $90^{\circ}C$) increased. This difference in currents indicates the relation of relative defects concentration between surface and interfacial defects of ZnO nanostructure. Our experimental approach has potential applicability in the analysis of influence on defects in ZnO devices.