• Journal of the Korean Graphic Arts Communication Society
• /
• v.22 no.1
• /
• pp.83-94
• /
• 2004

PSR ink is used to insulation coating material that heat resistance is. The use purpose is used for bridge prevention, circuit protection, stabilization of insulation. Heat-cured resin was used mainly on the materials of PSR inks. But, UV-curing type resin in used. Also, because of recently environmental problem, ink is going to water type. Purpose of this study is to develop PSR ink that can develop in pure water. and experiment did that do from that find suitable oligomer and monomer and does brand ratio differ. Specially Knew that is extent water soluble UV resin develop possible is DPHA 10~50% that A/A1924 is 50~90wt %, monomer. As a result, when ratio of A/A1924 and DPHA low viscosity epoxy resin is 5:1.5:1.5, could get high sensibility pattern repeatability, tack and alkali-resistance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.431-434
• /
• 2002

This paper reports on the evaluation of weathering resistance, tracking test and salt-fog of various kinds of cycloaliphatic epoxy systems. It was found that UV irradiation induced the loss of hydrophobic level due to the chain scission attack at the surface. It could be seen that samples containing an UV absorbent/antioxidant and a silicone oil additive knave a good performance in weathering ageing, whereas ATH filled ones have high resistance against tracking failure than others. Under salt-fog test, specimens mixed with silicone oil could suppress leakage current development. It was thought that silicone oil mixed into cycloaliphatic epoxy system could lead to lower the surface energy and to retain hydrophobic properties for a long time, which are desirable for outdoor performances.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.7
• /
• pp.382-386
• /
• 2004

A study has been made of surface modification of organic materials by ion implantation to increase the surface electrical properties. The substrate used were PET(polyethylene teraphtalate). N$^{＋}$, Ar$^{＋}$ implantation was peformed at energies of 40 keV and 50 keV with fluences from $5{\times}10^{15}$, $1{\times}10^{16}$,$7{\times}10^{16}$, $1{\times}10^{17}$/ ions/$cm^2$. UV/Vis, FT-IR and XPS spectroscopy measured for surface structure changes. Surface resistance decrease of implanted polymers was affected by ion implantation energy, ion species and ion dose rate. Surface conductivity of PET increased $2{\times}10^{9}$/∼$2{\times}10^{10}$/$\Omega$/sq by ion implantation. Result of various spectroscopy analysis, the cause of increasing PET surface conductivity was expected to breaking C=O bonds. It was formation carbon network structure by promote cross-linking and create C-C, C=C bonds.

• Structural Engineering and Mechanics
• /
• v.86 no.2
• /
• pp.211-220
• /
• 2023

The textile industry has benefited from nanotechnology in various fields of application as the use of nanomaterials, and nanotechnology is multiplying. Nanoparticles can increase the performance of textiles by up to 100 times when used in finishing, coating, and dyeing techniques, providing them with capabilities they did not previously possess. Nanotechnology is used in the textile chemical industry to produce sports mats with stain resistance, flame resistance, wrinkle resistance, moisture management, antimicrobial quality, and UV protection. The incorporation of nanomaterials into fabrics can have a significant effect on their properties, including shrinkage, strength, electrical conductivity, and flammability. Various inventions and innovations may result from nano-processed textiles in the future, thus leading to the advancement of science. This article presents the construction of sports engineering structures with high resistance to improve the quality of sports training. The mechanical properties of sports mats are improved with the help of nanotechnology. Strength, elasticity, and tear resistance are among these properties. This method enables the production of elastic, durable, and tear-resistant sports mats.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.15 no.2
• /
• pp.131-143
• /
• 1997

Surface sizing is one of the important process to the paper making. Surface sizing had an effect on penetration of oils, physical propertiesm water resistance for the paper. This study was carried out for the purpose of improving printability with surface sizing of domestic newspaper. The samples were prepared by means of TAPPI method(TAPPI 205 om~88), and were wested by IGT printability tester. The results of this study showed that the set-off was reduced on the surface sized with oxidized starch.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.816-819
• /
• 2008

A negative photoresist formulation was developed utilizing synthesized UV monomers containing imide linkage, photoinitiator, UV oligomer, and alkali developable polymer matrix. It was found that via-holes with good resolution, high transmittance and thermal resistance could be obtained by photolithographic process utilizing the negative-type photoresist formulations.

• Journal of Adhesion and Interface
• /
• v.4 no.1
• /
• pp.9-17
• /
• 2003

The UV hard coating materials are attracting more and more attention to modern industry, in terms of the development of low or non solvent coating materials which will contribute to economizing both materials and energy and to reducing pollution. This study was performed in order to invent UV curable coating materials containing colloidal silica which have actual industrial applications. As results of experiments, the oligomers type and the concentration of colloidal silica acrylate oligomer (SAOC) have an influence on various especially, The properties of UV hardening cooling, such as chemical, abrasion resistance and weatherability, were greatly enhanced, the impact properties of coated polycarbonate substrate were improved compared with the noncoated that. The UV cured films containing 30 wt% SAOC obtained showed the best properties.

• Journal of the Korean Ceramic Society
• /
• v.56 no.5
• /
• pp.461-467
• /
• 2019

Ink-jet printing technology, which utilizes a digitalized design to print fine ink directly on a substrate, has been of interest in various industries due to its high efficiency and adaptability to various materials. Recently, active attempts have been made to apply ceramic materials having excellent heat resistance, light resistance, and chemical resistance to the ink-jet printing process. In this study, ceramic ink was synthesized by combining ceramic pigments with UV curable polymer. 3D printability at various contact angles between ceramic ink and substrate was analyzed in detail. Rheological properties of the synthesized ceramic ink were optimized to meet the requirements of the ink-jet printing process, and the contact angle of UV curable ceramic ink was controlled through surface treatment of the substrate. The potential for additive manufacturing of ceramic material using ink-jet printing was investigated by analyzing the effect of contact angle control on ceramic ink droplets and their 3D printability.

• Journal of Photoscience
• /
• v.9 no.2
• /
• pp.162-165
• /
• 2002

Rice is widely cultivated in various regions throughout Asia. Over a five-year period, we investigated the effects of supplemental UVB radiation on the growth and yield of Japanese rice cultivars in the field. The findings of that study indicated that supplemental UVB radiation has inhibitory effects on the growth and grain development. Furthermore, we investigated the sensitivity to UVB radiation of rice cultivars of 5 Asian rice ecotypes, and found that rice cultivars vary widely in UVB sensitivity. The aim of our study is improving UVB resistance in plants by bioengineering or breeding programs. In order to make it, there is need to find the molecular origin of the sensitivity to UVB. Cyclobutane pyrimidine dimer (CPD) is major UV-induced DNA lesions. Plants possess two mechanisms to cope with such DNA damage. The first is the accumulation of UV-absorbing compounds. Our previous data showed that the steady-state CPD levels in leaves of rice grown under chronic radiation in any culture were not so greatly influenced by the increased UV-absorbing compounds content, although there was a significant positive correlation between the CPD levels induced by challenge UVB exposure and the UV-absorbing compounds content. The other is the repair of DNA damage. Photorepair is the major pathway in plants for repairing CPD. We found that the sensitivity to UVB could seriously correlate with the low ability in CPD photorepair in rice plants. These results suggest that photo lyase might be an excellent candidate for restoration by way of selective breeding or engineering in rice.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.88.1-88.1
• /
• 2015

In recent printed electronics technology, Photo-Sintering, a technique for sintering materials using a light source, has attracted attention as an alternative to time-consuming high-temperature thermal processes. The key principle of this technique is the selective heating of a strongly absorbent thin film, while preventing the heating of the transparent substrate by the light source. Many recent studies have used a flash lamp as the light source, and investigated the material-dependent effect of the width or intensity of the pulsed light. However, the flash lamp for sintering is not suitable for industry yet, because of needing too high power to sinter for a large scale. In energy-saving and large-scale sintering, LED technologies would be very useful in the near future. In this work, we investigated a sintering process for silver nanoparticles using UV-LED array. Silver nanoparticles in ink were inkjet-printed on a $1{\times}1cm$ area of a PET film and photo-sintered by 365 nm UV-LED module. A sheet resistance value as low as $72.6m{\Omega}/sq$ (2.3 - 4.5 times that of bulk silver) was obtained from the UV-LED sintering at 300 mW/cm2 for 50 min.