• Journal of Environmental Health Sciences
• /
• v.25 no.3
• /
• pp.64-69
• /
• 1999

This study was carried out the removal of Cr(VI) which was known to the toxic pollutant in industry using the process of UV and TiO$_2$ photocatalyst in a circular type reactor. In this experiment, the series of photocatalytic process for the removal of Cr(VI) has been selected as a model reaction in a circular type reactor in order to obtain the basic data on the influence of various experimental parameters such as circulation flow rate, pH of solution, initial Cr(VI) light illumination and TiO$_2$ dosage, and salicylic acid concentration. The results of this study were as follows; 1. With both UV light illumination and TiO$_2$ present, Cr(VI) was more effectively eliminated than with either UV or TiO$_2$ alone. 2. As the circulation flow rate of solution increased, the removal efficiency of Cr(VI) was increased. However, over 2.4 l/min of circulation flow rate, the efficiency wa limited. 3. A increase in the photocatalytic removal of Cr(VI) was noticed with decreasing pH. 4. An increase in the photocatalytic removal of Cr(VI) was noticed with decreasing Initial Cr(VI) concentration and first order kinetics was observed from the result at different initial concentration of Cr(VI). 5. Photocatalytic removal efficiency of Cr(VI) increased with increasing TiO$_2$ dosage. However, over 1.0 g/l of TiO$_2$ dosage, the efficiency reached a plateau. 6. As low concentration of saliculic acid were added, there was an increase in the removal efficiency of Cr(VI). However, over 300 mg/l of salicylic acid, the efficiecy was decreased. It eas found that application of photocatalysis to water treatment that contains both Cr(VI) and salicylic acid was possible.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.2
• /
• pp.140-147
• /
• 2004

An aqueous solution of a commercial liquid synthetic detergent for kitchen use was photodecomposed in the presence of titanium dioxides powder under an atmosphere of air at room temperature. Titanium dioxides were prepared by sol-gel method from titanium iso-propoxide at different R ratio($H_2O$/titanium iso-propoxide) and calcined at $500^{\circ}C$. All titanium dioxides were characterized by XRD, BET surface area analyzer and UV-VIS spectrometer. The surface area of titanium dioxides prepared at R ratio=6 appeared higher volume about 20% than commercial $TiO_2$ catalysts. XRD patterns of titania particles were observed mixing phase together with rutile and anatase type. Titanium dioxides prepared by sol-gel method show higher activity about 6% than commercial $TiO_2$ catalysts on the photocatalytic degradation of a commercial liquid synthetic detergent for kitchen. The concentration of the detergent decreased to about 90% of its initial value at illumination times of 2 hour. Illumination for 30 minutes decreased the concentration of oxygen to about one-fifth of the initial value.

• Journal of the Korean Society of Visualization
• /
• v.9 no.1
• /
• pp.36-41
• /
• 2011

It is highly needed to measure the dissolved oxygen (DO) concentration field in water for a variety of purposes such as biological, industrial, environmental monitoring and medical application. Application of PSP (Pressure Sensitive Paint) which is sensitive to oxygen concentration has been carried out to measure DO concentration field using PtOEP/PS film and intensity based method under the UV-LEDs illumination. A micro round water jet having 100% of DO was obliquely impinged on to a PtOEP/PS film coated plate placed in a 0% of DO water container. DO concentration fields on the impinging plate were quantitatively visualized with a $2.94\;{\mu}m$ of spatial resolution. Through pixel-by-pixel calibration, uncertainty of each pixel by different sensitivity, different dye concentration and non-uniformity of illumination was removed. It is demonstrated that the high DO concentration region was coincided with the impingement area. The DO concentration gradient due to DO diffusion was affected by Reynolds number.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.7
• /
• pp.685-692
• /
• 2016

In this paper, we not only take advantage of the SIFT features in banknote recognition, which has robustness to illumination changes, geometric rotation as well as scale changes, but also propose the hierarchical banknote recognition algorithm, which comprised of feature vector extraction from the frame grabbed image of the banknotes, and matching to the prepared data base of multinational banknotes by ANN algorithm. The images of banknote under the developed UV, IR and white illumination are used so as to extract the SIFT features peculiar to each banknotes. These SIFT features are used in recognition of the nationality as well as face value. We confirmed successful function of the proposed algorithm by applying the proposed algorithm to the banknotes of Korean and USD as well as EURO.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.3 s.52
• /
• pp.52-56
• /
• 2003

This study investigates the photoelectrochemical behavior of STS304 steel with TiO2 thin films coating, applied by sol-gel mehod, for the purpose of cathodic photoprotection of the steel corrosion. One time TiO2-coated STS304 steel, adapted with two kinds of TiO2 sol solution, has the most dominant photopotential abilities, which was -200mV vs. SCE and -500mV vs. SCE under illumination with 40 W fluorescent lamp, respectively. That had yielded more negative values than the corrosion potential of the bare metal(-130mv vs.SCE). The bleaching of TCE was confirmed on TiO2-coated STS304 steel under UV-illumination with 20W Black-light. This Study concluded that Ti02-coated STS304 exhibited both a cathodic photoprotection effect against corrosion and a photocatalytic self-cleaning effect.

• Journal of the Korean Society of Safety
• /
• v.16 no.3
• /
• pp.76-82
• /
• 2001

An aqueous solution of a commercial liquid synthetic detergent for kitchen use was photodecomposed in the presence of titanium dioxides ponder under an atmosphere of air at room temperature. Titanium dioxides were prepared by sol-gel method from titanium iso-propoxide at different R R ratio($H_2O$/titanium iso-propoxide) and calcined at $500^{\circ}C$. All titanium dioxides m characterized by XRD, BET surface area analyzer and UV-VIS spectrometer. The surface mea of titanium dioxides prepared at R ratio=6 appeared higher volume about 20% than commercial $TiO_2$ catalyses. XRD patterns of titania particles were observed mixing phase together with rutile and anatase type. Titanium dioxides prepared by sol-gel method show higher activity about 6% than commercial $TiO_2$ catalysts on the Photocatalytic foundation of a commercial liquid synthetic detergent for kitchen. The concentration of the detergent decreased to about 90%, of its initial value at illumination times of 2 hour. illumination for 30 minutes decreased the concentration of oxygen to about one-fifth of the initial value.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2002.10a
• /
• pp.307-311
• /
• 2002

This study was investigated the photoelectrochemical behavior of STS304 steel with $TiO_2$ thin films coating, applied by sol-gel method, for the purpose of cathodic photoprotection of the steel corrosion. One time $TiO_2$-coated STS304 steel adopted two kinds of $TiO_2$ sol solution has the most dominant photopotential abilities, which was -200mV vs. SCE and -500mV vs. SCE under illumination with 40W fluorescent lamp, respectively. That was more negative than the corrosion potential of the bare metal(-150 mV). The bleaching of TCE was confirmed on $TiO_2$-coated STS304 under UV-illumination with 20 W Black-light. This Study was concluded that $TiO_2$-coated STS304 exhibited both a cathodic photoprotection effect against corrosion and photocatalytic self-cleaning effect.

• Korean Journal of Optics and Photonics
• /
• v.28 no.6
• /
• pp.295-303
• /
• 2017

In this paper, we have studied a method of forming a line beam using a UV LED. The existing linear-type UV LED curing optical system is composed of several cylindrical lenses, but problems such as optical system alignment, enlargement of the module, efficiency, etc. may arise in the future. As an alternative to these problems, a bar-type TIR lens having a freeform surface only in the y-axis direction is designed, to verify that it shows advantages in maximum illuminance, uniformity of illuminance, and flux efficiency.

• Journal of Marine Bioscience and Biotechnology
• /
• v.6 no.2
• /
• pp.131-137
• /
• 2014

Ultraviolet-B radiation (UV-B) in sunlight causes biological damages such as erythema and blister on skin. Microalgae have been in the limelight as an attractive feedstock for manufacturing functional materials. This study focused on screening microalga with protection ability against UV-B. The microalgae were isolated from local areas on April to June 2013 as well as June 2014. The cells were grown under continuous illumination from fluorescent lamps at $136.3{\pm}2.2{\mu}E/m^2/s$ in BG-11 medium at $15^{\circ}C$ for 12-14 days. The selected cells were spread on BG-11 agar and were exposed to UV-B (312 nm) for 20 and 25 minutes. The 13 strains among selected algae were classified. Among these, 9 strains were Scenedesmus sp. and the remains were Chlorella sp. Based on this study, it seems that Scenedesmus sp. and Chlorella sp. have resistibility against ultraviolet. These results will help to study on UV protection using microalgae.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.4
• /
• pp.267-271
• /
• 2018

A high directivity TIR (total internal reflection) lens in the UV-A region was designed using a silicone resin, and a UV light source module with a maximum irradiation density of $150mW/cm^2$ was fabricated. The beam angle of the TIR lens was designed to be $8.04^{\circ}$ and the maximum diameter of the TIR lens was Ø13.5. A silicone resin having a UV transmittance of 93% and a refractive index of 1.4 at a wavelength of 365 nm was used, and the lens was manufactured using an aluminum mold, from which silicone could be easily released. The module was fabricated in a metal printed circuit board of COB (chip on board) type using a $0.75{\times}0.75mm^2$ UV chip. A jig was used to adjust the focal length between lens and chip and to fix the position of the lens. The optical characteristics such as illumination distributions of the lens and module were designed using 'LightTools' optical simulation software. The heat dissipation system was designed to use a forced-air cooling method using a heat-sink and fan.