• 한국항해학회지
• /
• 제21권3호
• /
• pp.75-81
• /
• 1997

현재 자동차나 선박등에 사용하는 직류모터 속도 제어용 스위칭 소자는 스위칭 과전압으로 인하여 때때로 손상되거나 오작동을 일으키기쉽다. 본논문은 dc 모터 제어용 반도체 스위칭소자의 내성특성을 개선한 것이다. 이를 위하여, 먼저 저전압 보호소자인 비리스터나 제너 다이오드 등 가운데에서 스위칭 과전압에 대해 내성을 갖는 이상적인 소자를 선택하기 위해 과전압 보호자의 등가회로를 분석 하였다. 나아가서 국제규정에서 정의된 의사 과전압 파형의 적절한 선택, 스위칭 소자의 손상과정과 손상원인을 규명하고, 순시과전압 전류의 변화에 따른 각각의 임피던스 조건을 고려하여 직류모터 제어용 반도체 스위칭 소자의 내성특성 개선하였다.

• Journal of Power Electronics
• /
• 제8권2호
• /
• pp.181-191
• /
• 2008

The task performed by induction motors grows increasingly complex in modern industry and hence improvements are sought in the field of fault diagnosis. It is essential to diagnose faults at their very inception, as unscheduled machine down time can upset critical dead lines and cause heavy financial losses. Artificial intelligence (AI) techniques have proved their ability in detection of incipient faults in electrical machines. This paper presents an application of AI techniques for the detection of inter-turn insulation and bearing wear faults in single-phase induction motors. The single-phase induction motor is considered a proto type model to create inter-turn insulation and bearing wear faults. The experimental data for motor intake current, rotor speed, stator winding temperature, bearing temperature and noise of the motor under running condition was generated in the laboratory. The different types of fault detectors were developed based upon three different AI techniques. The input parameters for these detectors were varied from two to five sequentially. The comparisons were made and the best fault detector was determined.

• 동력기계공학회지
• /
• 제10권4호
• /
• pp.71-77
• /
• 2006

This study introduces the seismic qualification of safety related equipments for nuclear power plants to verify the possibility of resonance in regard to the operating speed and the structural integrity due to external piping nozzle loads as well as seismic dynamic loads using El-Centro earthquake, which was occurred in the 1940's previously. As a first step, it is necessary to investigate the natural frequency of the vertical mixed flow pump in order to determine whether static or dynamic equipment comparing with seismic cut-off frequency, 33hz. Also the normal mode analysis was carried out with the introduction of seismic redesign straint at the middle of vertical pump to increase the natural frequency. In terms of structural integrity, the application of static analysis with normal, upset and faulted nozzle loads event was presented for the comparison of material allowable stress. Also the dynamic analysis was performed to show the design adequacy through the application to the case of El-Centro earthquake.

• 한국재료학회지
• /
• 제29권1호
• /
• pp.30-36
• /
• 2019

We evaluate the properties of friction welded STK400 steel tube in terms of the relationship between microstructures and mechanical properties. Friction welding is conducted at a rotation speed of 1,600 rpm and upset time of 3-7 sec for different thicknesses of STK 400 tubes. To analyse the grain boundary characteristic distributions(GBCDs) in the welded zone, electron backscattering diffraction(EBSD) method is introduced. The results show that a decrease in welding time (3 sec.) creates a notable increase grain refinement so that the average grain size decreases from $15.1{\mu}m$ in the base material to $4.5{\mu}m$ in the welded zone. These refined grains achieve significantly enhanced microhardness and a slightly higher yield and higher tensile strengths than those of the base material. In particular, all the tensile tested specimens experience a fracture aspect at the base material zone but not at the welded zone, which means a soundly welded state for all conditions.

• 소성∙가공
• /
• 제33권3호
• /
• pp.193-199
• /
• 2024

The friction welding characteristics of stainless steels, mainly used in energy and chemical plant industries due to its excellent corrosion resistance and high strength, was evaluated in this study. Friction welding was introduced and conducted at a rotation speed of 2,000 RPM, friction pressure of 30 MPa, burn-off length of 5 mm and upset pressure of 110 ~ 200 MPa on rod typed specimens. The grain boundary characteristics distributions such a grain size, shape, misorientation angle and kernel average misorientation of the welds were clarified by electron backscattering diffraction method. The application of friction welding on SUS304 alloy resulted in a significant refinement of the grain size in the weld zone (5.11 mm) compared to that of the base material (48.09 mm). The mechanical properties of the welds, on the other hand, appeared to be relatively low or similar to those of the base material, which were mainly caused by dislocation density in the initial material and grain refinement in the welds.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권8호
• /
• pp.891-898
• /
• 2005

Inertia welding is a solid-state welding process in which butt welds in materials are made in bar and in ring form at the joint race, and energy required lot welding is obtained from a rotating flywheel. The stored energy is converted to frictional heat at the interface under axial load. The quality of the welded joint depends on many parameters, including axial force, initial revolution speed and energy amount of upset. working time, and residual stresses in the joint. Inertia welding was conducted to make the large exhaust valve spindle for low speed marine diesel engine. superalloy Nimonic 80A for valve head of 540mm and high alloy SNCrW for valve stem of 115mm. Due to different material characteristics such as, thermal conductivity and flow stress. on the two sides of the weld interface, modeling is crucial in determining the optimal weld geometry and Parameters. FE simulation was performed by the commercial code DEFORM-2D. A good agreement between the Predicted and actual welded shape is observed. It is expected that modeling will significantly reduce the number of experimental trials needed to determine the weld parameters. especially for welds for which are very expensive materials or large shaft. Many kinds of tests, including macro and microstructure observation, chemical composition tensile , hardness and fatigue test , are conducted to evaluate the qualify of welded joints. Based on the results of the tests it can be concluded that the inertia welding joints of the superalloy exhaust valve spindle are better properties than the material specification of SNCrW.

• 한국재료학회지
• /
• 제27권5호
• /
• pp.276-280
• /
• 2017

This study was carried out to evaluate the developed microstructures and mechanical properties of friction welded A6063 alloy. For this work, specimens were prepared at a size of 12 mm ${\O}{\times}80mm$, and friction welding was carried out at a rotation speed of 2,000 RPM, friction pressure of $12kgf/cm^2$ and upset pressure of $25kgf/cm^2$. To perform an analysis of the grain boundary characteristic distributions, such as the grain size, orientation and misorientation angle distributions, the electron back-scattering diffraction method was used. In addition, in order to identify the dispersed intermetallic compounds of the base and welded materials, transmission electron microscopy was used. The experimental results found that the application of friction welding on A6063 led to significant grain refinement of the welded zone relative to that of the base material. Besides this, intermetallic compounds such as AlMnSi and $Al_2Cu$ were found to be dispersed with more refined size relative to that of the base material. This formation retains the mechanical properties of the welds, which results in the fracture aspect at the base material zone. Therefore, based on the developed microstructures and mechanical properties, the application of friction welding on A6063 could be used to obtain a sound weld zone.

• 수산해양기술연구
• /
• 제14권2호
• /
• pp.79-87
• /
• 1978

기관밸브용접 SCr4-21-4N 및 SUH3-21-4N을 연구선정된 최적마찰압접조건 하에서 마찰압접을 하고 이때 생기는 압접부의 잔류응력 및 경도의 peak 등 압접결함의 제거 및 압접성능개선을 위한 열처리에 관하여 실험연구한 결과 다음과 같은 결론을 얻었다. (1) 배기 valve용강 SCr4-21-4N 및 SUH3-21-4N의 마찰압접을 위한 최적조건으로서 회전수 3,000rpm, 마찰가열압 p 하(1)=8 kg/mm 상(2), upset 압 p 하(2)=20 kg/mm 상(2), 압접가열시간 t 하(1)=3초, upset 시간 2.5초를 선정한 것이 매우 타당함이 실험적으로 입증되었다. (2) 이종재질 SUH3-SUH31, SCr4-SUH31, SCr4-SUH3, SUH3-CRK22, SCr4-21-4N 및 SUH3-21-4N의 마찰압접에 관한 저자의 종래 연구와 본연구 결과는 압접부의 압접 특성이 서로 매우 일치하였다. (3) SCr4-21-4N 및 SUH3-21-4N의 마찰압접부의 잔류응력 및 전도의 peak를 제거하기 위한 최적열처리조건은 $600^{\circ}C$$\times$30min.$\times$room air cooling의 normalizing임이 확인되었다. (4) 이때 열처리 후에는, 열처리전의 인장강도의 약 20%가 감소했으나, 파단 위치는 열영향부로부터 모재 SCr4 및 SUH3 측으로 이동하였다. (5) 상기 최적조건 하에서 마찰압접되고 열처리된 압접부의 현미경 조직검사 결과, 압접부가 매우 좁고 압접결함이 없으며, 치밀하고 조밀한 조직의 우수한 압접이었음이 확인되었다. (6) 상기 최적조건은, 기관 valve 생산을 위한 타이종재질의 마찰압접조건으로도 응용될 수 있을 것이다.

• 수산해양기술연구
• /
• 제17권2호
• /
• pp.93-103
• /
• 1981

Si-Cr계 내열강 SUH3와 Cr-Ni계 stainless강 SUS 303 및 이들이 마찰용접재 SUH3-SUS303을 $1,060^{\circ}C$에서 용체화처리하고 다시 $700^{\circ}C$에서 10, 100시간 시효열처리한 각 시험편의 고온 피로강도에 대한 시효열처리의 효과를 알기 위하여 $700^{\circ}C$에서 고온 회전굽힘 피로시험을 하고 파약거동을 미시적으로 관찰하여 다음과 같은 결과를 얻었다. 1) SUH3재와 SUS303재의 최적마찰용접조건은 회전수 2420rpm, 마찰가압력 $8kg/mm^2$, 전 upset량 7mm(마찰가압시간 3sec, upset시간 2sec)이었다. 2) $700^{\circ}C$ 고온에서 장시간 이루어지는 고온피로시험에 있어, 용체화처리재의 S-N 곡선 경사부의 기울기가 가장 급하게 나타났다. 3) SUH3-SUS303 마찰용접재는 $1,060^{\circ}C$에서 1시간용체화 처리하고, $700^{\circ}C$에서 시효처리하는 경우 최적시효시간은 10시간이었다. 4) 10시간 시료재의 고온피로한도는 모재보다 SUH3은 75.4%, SUS303은 28.5% 높았으며, 용접재 SUH3-SUS303은 44.2% 정도 높았다. 100시간 시효재는 모재보다 SUH3은 64.91% SUS303은 30.4% 높았으며, SUH3-SUS303은 30.4% 높았으며, SUH3-SUS303은 36.6% 높았다. 5) 마찰용접재의 상온 및 고온의 피로파단은 모두 SUS303의 모재측에 발생하였으며, 용접면에서의 파단은 전혀 없었다. 6) SUS303재와 마찰용접재 SUH3-SUS303재의 크랙은 입내파양형이었으나 SUH3은 입계크랙의 전파로 파양한다.

• 대한기계학회논문집
• /
• 제11권5호
• /
• pp.762-771
• /
• 1987

본 연구에서는 국산 구조용 강인 SM45C와 SUS304재를 마찰가열압력과 업셋압 력을 서로 변화시키고 업셋시간을 2초로 고정하여 압접시간 10초를 기준으로 하여 변 화시키면서 마찰압접한 후 압접시간 변화에 따른 인장강도의 변화와 업셋량 변화에 따 른 인장강도 및 굽힘강도를 고찰하였다.또 최고 강도치를 나타내는 압접조건을 구 한 후 미소 경도치 및 이종재의 압접부에서 미소하게 변화하는 조직변화도 함께 고찰 하였다.