• Proceedings of the IEEK Conference
• /
• 2002.07c
• /
• pp.1575-1577
• /
• 2002

In this research we propose a method far rain rate estimation by using Doppler spectrum's data of wind profiler. The Doppler spectrum is used to calculate the wind velocity and wind direction. But in this research uses the parameters from Doppler spectrum, it calculates the rain rate. The rain rate estimation in this method will be compared to the obtained rain rate from the surface rain gauge. Two equipments are installed in the same area. The correlation coefficient between rain rate measuring method is 0.65.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.05a
• /
• pp.304-307
• /
• 2004

This paper simulated partial discharge caused by 22.9[kV] power cable using XLPE(Peroxide Crosslinkable Polyethylene) insulation having the outside damage. As one of the insulation diagnostic method a radiated electromagnetic waves were measured by an UHF method using a BiconiLog antenna(EMCO-3142) and a spectrum analyzer used to measure EMI, EMC. From results of this study, It was confirmed that discharge progress were possible to be estimated by the proposed method.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.24 no.4
• /
• pp.625-634
• /
• 2014

Tactical networks is being operated in configuration that consisting of a variety of characteristics communication equipments and heterogeneous networks. In this configurations, end-to-end communication can be achieved using interworking gateway for converting the data format of the network and using encryption algorithm of the networks. The use of mechanism results in a problem that secure data cannot be transferred directly, reprocessing and processing delay of communication in heterogeneous tactical networks. That is, for encoding and decoding of data, the decryption of encrypted data and re-encryption processing must be required at the gateway between different networks. In this paper proposes to mechanism for end-to-end secure communication in heterogeneous tactical networks. Using the proposed method, end-to-end secure communication between heterogeneous tactical networks(PSTN-UHF networks) which removes the necessity of a gateway for converting data into data formats suitable for network to remove a transmission delay factor and enable real-time voice and data communication and achieve end-to-end security for heterogeneous tactical networks. we propose a novel mechanism for end-to-end secure communication over PSTN and UHF networks and evaluate against the performance of conventional mechanism. Our proposal is confirmed removal of security vulnerabilities, end-to-end secure communication in heterogeneous tactical networks.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.1
• /
• pp.94-103
• /
• 2005

The low foamed high strengthen styrofoam samples made by dielectric heating are discussed. We used the oscillator which have the frequency of 13.6 MHz and the power of 7 kW. 3 times expanded beads by steaming method were used in our foam-molding test. Internal fusion properties and density of internal structure were improved by dielectric foaming process. At the temperature of $105-110^{\circ}C$, the internal fusion property was maximally improved.

• Journal of information and communication convergence engineering
• /
• v.21 no.3
• /
• pp.233-238
• /
• 2023

This study presents a method for identifying partial discharge defects in an eco-friendly gas insulated system using a backpropagation algorithm. Four partial discharge (PD) electrode systems, namely, a free-moving particle, protrusion on the conductor, protrusion on the enclosure, and voids, were designed to simulate PD defects that can occur during the operation of eco-friendly gas-insulated switchgear. The PD signals were measured using an ultrahigh-frequency sensor as a nonconventional method based on IEC 62478. To identify the types of PD defects, the PD parameters of single PD pulses in the time and frequency domains and the phase-resolved partial discharge patterns were extracted, and a back-propagation algorithm in the artificial neural network was designed using a virtual instrument based on LabVIEW. The backpropagation algorithm proposed in this paper has an accuracy rate of over 90% for identifying the types of PD defects, and the result is expected to be used as a reference database for asset management and maintenance work for eco-friendly gas-insulated power equipment.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.3
• /
• pp.367-376
• /
• 2012

This paper describes a Adaptive Impedance Tuning Circuit which can be adaptively tuned between circuit's characteristic impedance and the arbitrary load impedance. The Adaptive Impedance Tuning Circuit is consisted of such parts as mismatch sensor, impedance tuner and tuning algorithm. Each parts's design methods proposed in other papers are compared with their advantages and disadvantages. And we propose simple design method for Adaptive Impedance Tuning Circuit using a ${\lambda}/4$ transmission line and ${\pi}$-network. Calculation formulas and selection algorithm from calculated values of a complex load impedance are proposed and simulation using induced calculation formulas and selection algorithm is performed. Simulation results show good agreement with theoretical predictions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.69-75
• /
• 2010

In this paper, with using the clapp type VCO(Voltage Controlled Osillator) configuration a wideband frequency synthesizer in UHF band is proposed. In order to design a wideband frequency synthesizer, the variation of phase in the negative resistance circuit as well as the load circuit was analyzed. Based on this result we propose a method to widen the operation range of the VCO. A frequency synthesizer using the proposed wideband VCO was designed and fabricated. It is shown that the synthesizer has the operating frequency range of 740~1,530 MHz by 0~5 V varactor tuning voltage, and it had the output power of 2~-6 dBm. Moreover, the phase noise measured as -77 dBc/Hz at 10 kHz offset, and as -108 dBc/Hz at 100 kHz offset from the oscillation frequency.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.5
• /
• pp.813-818
• /
• 2020

This study is a study on the characteristics and analysis of the reflected signals about the target in the VHF band. In advance, the RCS(Radar Cross Section) characteristics of the target were analyzed by using the CST electromagnetic analysis tool, and the target was detected by using the Bi-Static method, and the change in the signal-to-noise ratio was tested. The test results show similar results with no significant fluctuations in the signal-to-noise ratio characteristics for the detection of signals reflected on the target, such as the results for RCS analysis according to the pre-incidence angle. In the future, this study will be used for RCS analysis of the targets and target detection of Radar in VHF/UHF band with relatively large wavelength compared to the X band.

• Journal of Satellite, Information and Communications
• /
• v.12 no.1
• /
• pp.94-100
• /
• 2017

In this paper, we suggest a design method of a metamaterial-based low-profile antenna working at 425 MHz for LEO/Cube satellites. Satellites play an important role in linking th remote nodes in a wireless communication network and covering wide areas of the globe. Especially, an increasing number of universities or individuals aspire having their own satellites and build low-budget structures such as cube satellites in LEO and the ways to reduce the sizes of their satellites. Since the antenna occupies a major portion of the satellite surface, the antenna should be miniaturized for lighter weight. The proposed metamaterial low-profile antenna, unlike the conventional patch antenna, produces such a zeroth-order resonance to create an omnidirectional radiation pattern. Also, it is connected to a UHF waveguide bandpass filter as the feeding system to examine the possible change in the situation that the antenna is combined with the system. The performances of the monopole and proposed metamaterial antennas are compared to one another.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.4
• /
• pp.1789-1796
• /
• 2012

In this paper, a new high-efficiency CMOS bridge rectifier for driving RFID tag chips is designed and analyzed. The input stage of the proposed rectifier is designed as a cascade structure connected with two NMOSs for reducing the gate capacitance by circuitry method, which is the main path of the leakage current that is increased when the operating frequency is increased. This gate capacitance reduction technique using the cascade input stage for reducing the gate leakage current is presented theoretically. The output characteristics of the proposed rectifier are derived analytically using its high frequency small-signal equivalent circuit. For the general load resistance of $50K{\Omega}$, the proposed rectifier shows better power conversion efficiencies of 28.9% for 915MHz UHF (for ISO 18000 -6) and 15.3% for 2.45GHz microwave (for ISO 18000-4) than those of 26.3% and 26.8% for 915MHz, and 13.2% and 12.6% for 2.45GHz of compared other two existing rectifiers. Therefore, the proposed rectifier may be used as a general purpose rectifier to drive tag chips for various RFID systems.