• 전기학회논문지
• /
• 제57권11호
• /
• pp.2047-2053
• /
• 2008

Auto-ID industries and their services have been improved since decades ago, and radio frequency identification (RFID) has been contributing in many applications. Product management can be the foremost example. In our industrial experiences, RFID in ultra high frequency (UHF) band provides much longer interrogation ranges than that of 13.56MHz; many more applications exist thereby. There should be several interesting and useful ideas on UHF RFID; however, those ideas can be limited due to the inevitable environmental circumstances that restrict the interrogation range in shorten value. This paper discusses the propagation interference among different types of readers (e.g, mobile RFID readers in stationary reader zone) in dense-reader environment. In most cases, UHF RFIDs in Korea will be dependent on the UHF mobile RFIDs. In this sense, the UHF mobile users accidently move into the stationary reader's interrogation zone. This is serious problem. In this paper, we analyze propagation loss and propose the effective channel allocation scheme that can contribute developing less-invasive UHF RFID networks. The simulation and practical measurement process using the commercial CAD tools and measurement equipments are presented.

• 전기학회논문지
• /
• 제57권2호
• /
• pp.252-255
• /
• 2008

A study for discharge pattern analysis partial and fault location by use of UHF sensors in GIS. However, in the latter case, the results considered the velocity of EM waves modified by the waveguide characteristics of GIS bus bar were not reported yet. In this paper, UHF wide band sensor to detect partial discharge signals have been designed and manufactured to get the widest band characteristic by an application of Fat-Dipole UHF antenna and the result that the transmission velocity of EM waves is 2/3 of the light have been got through the consideration of waveguide characteristics. Also, to verify applicability on site of the developed method, self-designed external type UHF sensor have been installed on operating GIS in Korea Midland Power co. and detected location of the fault. Through the fault have been found at the location, the reliability of the developed method have been proved.

• 한국정밀공학회지
• /
• 제33권3호
• /
• pp.191-198
• /
• 2016

Traceability is essential in modern automotive manufacturing. Among existing technologies, RFID is the most promising choice for this purpose. However, due to the harsh conditions of production lines, especially in the paint shop, automobile OEMs would require expensive dedicated RFID tags and readers, which are incompatible with standard RFID technologies. Unlike the manufacturing industry, the logistics industry uses UHF label tags for track and trace, which provides high performance and a low price. Recently, this technology has improved to the extent that it can be used in harsh conditions such as on metal parts or in liquid. Herein, we assess the technical, operational, and economic feasibility of UHF label-tag technology for seamless end-toend traceability. Based on prototyping, lab/field tests, and cost-benefit analysis, we have proven that the single disposable UHF tags can successfully replace the problematic and expensive tags used in most domestic automobile OEMs today.

• Journal of electromagnetic engineering and science
• /
• 제7권3호
• /
• pp.134-137
• /
• 2007

This paper presents the design of the compact UHF Bandpass filter of CT-type with a novel mixed coupling topology. In further detail, this new coupling structure mathematically equals the transmission zero that enables particularly the better rejection performance in the stopband without increasing the filter's order. To envision this design concept, we fabricated a microstrip filter whose measurement proves to agree with the predicted performance and the suggested coupling structure reduces the overall size, and will be possibly used in the miniaturized UHF apparatus such as the RFID system.

• 전기학회논문지
• /
• 제57권5호
• /
• pp.889-895
• /
• 2008

In this paper a Fractional-N frequency synthesizer is designed for UHF RFID readers. It satisfies the ISO/IEC frequency band($860{\sim}960MHz$) and is also applicable to mobile RFID readers. A VCO is designed to operate at 1.8GHz band such that the LO pulling effect is minimized. The 900MHz differential I/Q LO signals are obtained by dividing the differential signal from an integrated 1.8GHz VCO. It is designed using a $0.18{\mu}m$ RF CMOS process. The measured results show that the designed circuit has a phase noise of -103dBc/Hz at 100KHz offset and consumes 9mA from a 1.8V supply. The channel switching time of $10{\mu}s$ over 5MHz transition have been achieved, and the chip size including PADs is $1.8{\times}0.99mm^2$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1915-1917
• /
• 2000

Laboratory experiments and on site measurements were conducted to detect partial discharges in GIS(Gas Insulated Switchgear) using the UHF(Ultra High Frequency) technique that has been applied many places in the world. Experimental results were in good agreement with calculation in locating a partial discharge source using mock-up GIS. Defect type and its location were inferred after a measurement on 345 kV GIS that showed some abnormal phenomenon. Precise examination inside the GIS coincided with the results inferred from the measurement. High reliability of UHF technique for site application was confirmed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.2038-2039
• /
• 2007

In this work, a novel semi-internal type UHF PD sensor has been proposed and related investigations has been performed in order to detect the partial discharges that could be possibly produced at the insulation system of the gas insulated switchgear(GIS). This sensor was designed to mount on the CT terminal hole of GIS using the spiral antenna theory. Therefore this type sensor can be install on GIS during the power apparatus has been operation and better sensitivity compare to the commercial external type UHF PD sensor.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2008년도 춘계종합학술대회 A
• /
• pp.685-688
• /
• 2008

평면 안테나는 막대형 모노폴 안테나에 비하여 돌출부위가 없으므로 옥외 계측자동화 시설의 데이터 전송에 효과적으로 사용될 수 있다. 그러나 UHF 대역에서는 크기로 인하여 평면 안테나의 사용이 상당히 제한되고 있다. 본 논문에서는 400MHz UHF 대역의 ISM 밴드를 사용하는 AMR(Automatic Meter Reading) 시스템에 적용할 수 있는 평면 안테나의 소형화 설계를 연구하였다. 평면 안테나는 FR-4 기판의 마이크로스트립 패치 구조이며, 소형화는 패치에 슬롯을 장하하여 설계되었다. 먼저 직사각형 슬롯을 사용하여 슬롯이 안테나 소형화에 미치는 영향을 파악한 후 보다 복잡한 형태의 슬롯을 적용하여 UHF 대역에서 37.9% 크기가 감소된 안테나를 제작하였다. 제작된 안테나는 야외 설치를 위한 안테나 보호용으로 표면에 에폭시 코팅 처리가 이루어졌으며, 공진 주파수 변화에 대한 에폭시 코팅의 영향도 분석되었다.

• 한국정보통신학회논문지
• /
• 제12권6호
• /
• pp.979-983
• /
• 2008

평면 안테나는 막대형 모노폴 안테나에 비하여 돌출부위가 없으므로 옥외 계측자동화시설의 데이터 전송에 효과적으로 사용될 수 있다. 그러나 UHF 대역에서는 크기로 인하여 평면 안테나의 사용이 상당히 제한되고 있다. 본 논문에서는 400MHz UHF 대역의 ISM 밴드를 사용하는 AMR (Automatic Meter Reading) 시스템에 적용할 수 있는 평면 안테나의 소형화 설계를 연구하였다. 평면 안테나는 FR-4 기판의 마이크로스트립 패치 구조이며, 소형화는 패치에 슬롯을 장하하여 설계되었다. 먼저 직사각형 슬롯을 사용하여 슬롯이 안테나 소형화에 미치는 영향을 파악한 후 보다 복잡한 형태의 슬롯을 적용하여 UHF 대역에서 37.9% 크기가 감소된 안테나를 제작하였다. 제작된 안테나는 야외 설치를 위한 안테나 보호용으로 표면에 에폭시 코팅 처리가 이루어졌으며, 공진 주파수 변화에 대한 에폭시 코팅의 영향도 분석되었다.

• 전기학회논문지
• /
• 제59권4호
• /
• pp.728-732
• /
• 2010

GIS(Gas insulated switching gear) is power equipment with excellent dielectric strength and is economy merit in high confidence and stability. Recently, because equipment of GIS was occurring problem of confidence used for a long time, partial discharge on-line diagnosis systems have been importantly recognized. Partial discharge (PD) detection is an effective means for monitoring and evaluation of dielectric condition of gas insulated system (GIS). The ultra-high-frequency (UHF) PD detection technique can detect and locate the PD sources inside GIS by detecting electromagnetic wave emitted from PD source. Therefore, real-time diagnostic system using UHF detection method has been developed for this application is being expanded gradually. However, the signal of partial discharge occurring in SF6 gas is very weak and susceptible to external noises which mainly consist of PD in air. Thus, it is important to distinguish the PD in SF6 gas more sensitively from the external noises. Unfortunately, these external noise signals and the partial discharge signals have very similar characteristics. Therefore, to solve this problem, we need the signal processing method for distinguish partial discharge signals with external noise signals for improvement of SNR(signal to noise ratio) and sensitivity. In this paper, we proposed internal signal processing method for removing external noise signals with built-in pre.amplifier and frequency conversion circuit.