• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.125-131
• /
• 2003

The U-draw bending operation is known as a representative test method for springback evaluation of sheet metals since the sheet in U-draw bending operation undergoes stretching, bending and unbending deformations occurred at read stamping process. In this study, a simplified approach was proposed for predicting springback and side-wall curls in U-draw bending operations, using moment-curvature relationships derived for sheets undergoing stretching, bending and unbending deformation.

• 소성∙가공
• /
• 제13권8호
• /
• pp.678-688
• /
• 2004

The U-draw bending operation is known as a representative test method for springback evaluation of sheet metals since the sheet in U-draw bending operation undergoes stretching, bending and unbending deformations occurred at the stamping process. In this study, a simplified approach was proposed for predicting springback and side-wall curls of tailor-welded blank in U-draw bending operations, using moment-curvature relationships derived for sheets undergoing stretching, bending and unbending deformation. Two different welded strips were adopted to compare the effects of weld-line locations on the springback. One (type A) was welded along the centerline of the strip-width and the other (type B) was welded along the centerline of the strip-length. To investigate the effect of different thickness combination on the springback, the tailor-welded strips were joined by the laser welding process and consisted of three types of thickness combinations of sheets, SCP1 0.8t ＊ SCP1 1.2t, SCP1 0.8t ＊ SCP1 1.6t and SCP1 0.8t ＊ TRIP 1.0t. Some calculated results by the simplified formula were compared with experimental results.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.148-151
• /
• 2003

The purpose of this study is to investigate the manufacturing technique on the U type Draw-Bending of inner groove tube. The U type tube requires the quality of product that satisfy sufficient conditions for a heat exchanger. The mandrel components act the important roles that prevent wrinkles and keep the shape of cross section of bended tube at bending process. We performed the FEM simulation using LS-DYNA software and the bending test of inner groove tube and then, compared bending simulation with bending test results about mandrel ball diameter, mandrel position and optimal clearance between mandrel and tube.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.787-788
• /
• 2012

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1705-1708
• /
• 2003

The purpose of this study is to investigate the manufacturing technique on the U type Draw-Bending of inner grooved tube. This bending process make the U shape tube by Hair Pin Bending machine. The U type tube requires the quality of product that satisfy sufficient conditions for a heat exchanger. The mandrel components act the important roles that prevent wrinkles and keep the shape of cross section of bended tube at bending process. We performed the FEM simulation using LS-DYNA software and the bending test of inner groove tube and then, compared bending simulation with bending test results about mandrel ball diameter, mandrel position and optimal clearance between mandrel and tube.

• 소성∙가공
• /
• 제3권1호
• /
• pp.51-62
• /
• 1994

Cup drawing test and U-bending test were performed to evaluate the friction characteristics of sheet materials for the different deformation modes involved in stamping process. The coefficient of friction calculated from the each test was compared to that obtained from the draw bead friction test. It was clarified that the cup drawing test could be simply used for evaluating the friction characteristic of sheet material in deep drawing process with high contacting pressure. However the U-bending test is suitable to evaluate the frictional characteristic of sheet material in bending process with low contacting pressure.

• 소성∙가공
• /
• 제23권7호
• /
• pp.405-412
• /
• 2014

As a major type of heat exchanger, the steam generator (SG) produces steam from heat energy of a nuclear power plant reactor. The steam produced by the steam generator flows into a turbine, and plays an important role in electric power generation. The heat transfer tubes in the steam generator consist of approximately 10,000 U-shaped tubes, which perform a structural role and act as thermal boundaries. The heat transfer tubes conduct the thermal energy between the primary coolant (about $320^{\circ}C$, $157kgf/cm^2$) obtained from the reactor and the secondary coolant (about $260^{\circ}C$, $60kgf/cm^2$) as part of the secondary system. Recently, the heat transfer tubes in the steam generator of the pressurized water reactor (PWR) are primarily produced from Alloy 600 and Alloy 690 seamless tubes. As a pilot study to find process parameters for the cold U-bending process using rotary draw bending, numerical and experimental investigations were conducted to produce U-shaped tubes from long straight SUS304L seamless tubes. 3D finite element simulations were run using ABAQUS Explicit with consideration of the elastic recovery. The process parameters studied were the angular speed, the operation period and the bending angle. Experimental verifications were conducted to insure the suitability of the final U-shaped configurations with respect to both ovality and wall thickness.

• 소성∙가공
• /
• 제20권5호
• /
• pp.344-349
• /
• 2011

Variation of contact pressure causes change of friction coefficient, which in turn changes stress distribution in the sheet being formed and final springback. In the present study, U-draw bending experiments were carried out under constant blank holding force(BHF) and different blank sizes, and finite element analysis was conducted with and without considering contact pressure effect on friction. When the BHF was sufficiently high, the degree of springback was different between constant blank holding pressure condition and that with varying blank holding pressure. Finite element analysis considering the influence of contact pressure effect on friction could explain the occurrence of springback.

• 소성∙가공
• /
• 제15권4호
• /
• pp.295-303
• /
• 2006

Optimization is carried out to determine process parameters which reduce the amount of springback and improve shape accuracy of a deep drawn product in sheet metal forming process. The study uses the amount of stress deviation along the thickness direction in the deep drawn product as an indicator of springback instead of springback simulation. The scheme incorporates with an explicit elasto-plastic finite element method for calculation of the final shape and the stress deviation The optimization method adopts the response surface method in order to seek for the optimum condition of process parameters such as the blank holding force and the draw-bead force. The present scheme is applied to design of the variable blank holding force in an U-draw bending process and the application is further extend ε d to the design of draw-bead force in a front side member formed with advanced high strength steel (AHSS) sheets of DP60. Results show that design of process parameter is well performed to decrease the stress deviation through the thickness and to reduce the amount of springback. The present analysis provides a guideline in a design stage for controlling the springback based on the finite element simulation of the complicated parts.

• 품질경영학회지
• /
• 제36권4호
• /
• pp.29-36
• /
• 2008

최근 자동차 경량화를 위한 부단한 노력이 진행되고 있다. 이 목적에서, HSS (high strength steel)는 전통적인 연강 (mild steel)의 대안으로 널리 사용되고 있다. 본 연구의 목적은 판금의 형단조에 있어서의 공구와 공정설계를 위하여 HSS의 스프링백(springback)을 정확히 예측하기 위한 성공적인 방법론을 추구하고자 함이다. 연구를 위하여 먼저 스프링백의 개념과 그의 측정치들을 설명했으며 U-draw bending 시험을 수행하였다. 시험 결과 및 선정된 파라메터들 중심의 수행평가기준에 근거하여, 주어진 파라메터 조합들을 중심으로 유한요소 해석을 수행하였다. 직교배열을 통하여 스프링백에 대한 인자 효과들을 포괄적으로 분석하였으며 최적 인자 조합들을 도출하였다. 이 과정에서 직교배열상의 한 조합 전체의 데이터가 가용하지 않는 문제가 수반되었으며, 반복적으로 signal-to-noise 비(ratio)를 개선해가는 기법을 적용하여 해결하였다.