• Journal of Sensor Science and Technology
• /
• v.4 no.1
• /
• pp.3-8
• /
• 1995

n-ITO/p-PSL heterojunction photodetector have been fabricated on the Si wafer by using ITO(indium tin oxide) and PSL(porous silicon layer). They were anodized selectively by using silicon nitride and Ni-Cr/Au and were passivated by using ITO as well as being isolated by using mesa structure. With white light from 0 to 3000 Lux, the photocurrent varied linearly with incident light intensity. The reverse characteristics of fabricated devices were very stable up to a bias voltage of -40V and dark current density was about $40nA/mm^{2}$. When the device was exposed by Xe lamp whose wavelength range from 400nm to 1100nm, the maximum photo responsivity was about 0.6A/W between 600 and 700nm. Variation of the characteristics of fabricated devices after 5 weeks was negligible.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.11-11
• /
• 2008

ZnO has a very large exciton binding energy (60 meV) as well as thermal and chemical stability, which are expected to allow efficient excitonic emission, even at room temperature. ZnO based electronic devices have attracted increasing interest as the backplanes for applications in the next-generation displays, such as active-matrix liquid crystal displays (AMLCDs) and active-matrix organic light emitting diodes (AMOLEDs), and in solid state lighting systems as a substitution for GaN based light emitting diodes (LEDs). Most of these electronic devices employ the electrical behavior of n-type semiconducting active oxides due to the difficulty in obtaining a p-type film with long-term stability and high performance. p-type ZnO films can be produced by substituting group V elements (N, P, and As) for the O sites or group I elements (Li, Na, and K) for Zn sites. However, the achievement of p-type ZnO is a difficult task due to self-compensation induced from intrinsic donor defects, such as O vacancies (Vo) and Zn interstitials ($Zn_i$), or an unintentional extrinsic donor such as H. Phosphorus (P) doped ZnO thin films were grown on c-sapphire substrates by radio frequency magnetron sputtering with various Ar/ $O_2$ gas ratios. Control of the electrical types in the P-doped ZnO films was achieved by varying the gas ratio with out post-annealing. The P-doped ZnO films grown at a Ar/ $O_2$ ratio of 3/1 showed p-type conductivity with a hole concentration and hole mobility of $10^{-17}cm^{-3}$ and $2.5cm^2/V{\cdot}s$, respectively. X-ray diffraction showed that the ZnO (0002) peak shifted to lower angle due to the positioning of $p^{3-}$ ions with a smaller ionic radius in the $O^{2-}$ sites. This indicates that a p-type mechanism was due to the substitutional Po. The low-temperature photoluminescence of the p-type ZnO films showed p-type related neutral acceptor-bound exciton emission. The p-ZnO/n-Si heterojunction LEO showed typical rectification behavior, which confirmed the p-type characteristics of the ZnO films in the as-deposited status, despite the deep-level related electroluminescence emission.

• Current Photovoltaic Research
• /
• v.8 no.1
• /
• pp.6-11
• /
• 2020

The power conversion efficiency (PCE) of a two-terminal tandem solar cell depends upon the tunnel-recombination junction (TRJ) between the top and bottom sub-cells. An optimized TRJ in a tandem cell helps improve its open-circuit voltage (V_oc), short-circuit current density (J_sc), fill factor (FF), and efficiency (PCE). One of the parameters that affect the TRJ is the buffer layer thickness. Therefore, we investigated various TRJs by varying the thickness of the buffer or intermediate layer (TRJ-buffer) in between the highly doped p-type and n-type layers of the TRJ. The TRJ-buffer layer was p-type nc-Si:H, with a doping of 0.06%, an activation energy (E_a) of 43 meV, an optical gap (E_g) of 2.04 eV, and its thickness was varied from 0 nm to 125 nm. The tandem solar cells we investigated were a combination of a heterojunction with intrinsic thin layer (HIT) bottom sub-cell and an a-Si:H (amorphous silicon) top sub-cell. The initial cell efficiency without the TRJ buffer was 7.65% while with an optimized buffer layer, its efficiency improved to 11.74%, i.e., an improvement in efficiency by a factor of 1.53.

• Current Photovoltaic Research
• /
• v.11 no.2
• /
• pp.39-43
• /
• 2023

Carrier-selective contacts (CSCs) solar cells are considerably attractive on highly efficient crystalline silicon heterojunction (SHJ) solar cells due to their advantages of high thermal tolerance and the simple fabrication process. CSCs solar cells require a hole selective contact (HSC) layer that selectively collects only holes. In order to selectively collect holes, it must have a work function characteristic of 5.0 eV or more when contacted with n-type Si. The VO_x, NiO_x, and CuI_x thin films were fabricated and analyzed respectively to confirm their potential usage as a hole-selective contact (HSC) layer. All thin films showed characteristics of band-gap engergy > 3.0 eV, work function > 5.0 eV and minority carrier lifetime > 1.5 ms.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.6
• /
• pp.30-37
• /
• 1989

The PIN type a-SiC:H/a-Si:H heterojunction solar cells were fabricated by using the rf glow discharge decomposition of $SiH_4$ mixed with $CH_4,B_2,H_6\;and\;PH_3.$ The efficiency of the solar cell of the $SnO_2/ITO$ was higher than that of ITO transparent oxide layer by 1.5%. The P layer was prepared with the thickness of $100{\AA}$ and $CH_4/SiH_4$ ration of 5. The I layer has been deposited on the P layer and it is not pure intrinsic but near N type. So $SiH_4$ mixed with $B_2H_6$ of 0.3ppm was used to change this N type nature to intrinsic having the thickness of 5000${\AA}$. And consecutively, the N layer was deposited with t ethickness of $400{\AA}$ using $SiH_4/PH_3$ mixtures. The solar cell demonstrated 0.94V of $V_{oc'}$ 14.6mA/cm of $J_{sc}$ and 58.2% of FF, resulting the efficiency of 8.0%. To minimize loss by the reflection of light, $MgF_2$ layer was coated on the lgass and the efficiency was improved by 0.5%. Therefore, the solar cell indicated overall efficiency of 8.5%.