• International Journal of Aeronautical and Space Sciences
• /
• v.16 no.2
• /
• pp.148-156
• /
• 2015

A continuous type side jet controller which has four nozzles with thrust control devices was considered. It is deployed to a missile for high maneuverability and fast controllability in the terminal guidance phase. However, it causes more complex aerodynamic jet interactions between the side jet and the supersonic free stream than does the conventional impulse type side jet with a small single thruster. In this paper, a numerical investigation of the jet interference effects for the missile equipped with a continuous type side jet thruster is presented. A three-dimensional flow field was simulated by using a commercial unstructured-based CFD solver. The numerical simulation method was validated through comparison with wind tunnel test results for the single jet. The method of defining jet direction for this type of side jet control to minimize simulation cases was also introduced. Flow fields investigation and jet interaction effects for various flow conditions, jet pressure ratios and defined jet direction conditions were performed. From the numerical simulation for the continuous type side jet, extensive aerodynamic interference data were obtained to construct an aerodynamic coefficients database for precise missile control.

• International Journal of Aeronautical and Space Sciences
• /
• v.17 no.2
• /
• pp.195-203
• /
• 2016

In order to overcome the influence of system stability and accuracy caused by uncertainty, estimation errors and external disturbances in Eight-Rotor MAV, L2 gain control method was proposed based on interval type II fuzzy neural network identification here. In this control strategy, interval type II fuzzy neural network is used to estimate the uncertainty and non-linearity factor of the dynamic system, the adaptive variable structure controller is applied to compensate the estimation errors of interval type II fuzzy neural network, and at last, L2 gain control method is employed to suppress the effect produced by external disturbance on system, which is expected to possess robustness for the uncertainty and non-linearity. Finally, the validity of the L2 gain control method based on interval type II fuzzy neural network identifier applied to the Eight-Rotor MAV attitude system has been verified by three prototy experiments.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.999-1004
• /
• 2005

An algorithm for a hybrid controller consists of a sliding mode control part and a fuzzy logic part which ar purposely for nonlinear systems. The sliding mode part of the solution is based on "eigenvalue/vector"-type controller is used as the backstepping approach for tracking errors. The fuzzy logic part is a Mamdani fuzzy model. This is designed by applying sliding mode control (SMC) method to the dynamic model. The main objective is to keep the update dynamics in a stable region by used SMC. After that the plant behavior is presented to train procedure of adaptive neuro-fuzzy inference systems (ANFIS). ANFIS architecture is determined and the relevant formulation for the approach is given. Using the error (e) and rate of error (de), occur due to the difference between the desired output value (yd) and the actual output value (y) of the system. A dynamic adaptation law is proposed and proved the particularly chosen form of the adaptation strategy. Subsequently VSC creates a sliding mode in the plant behavior while the parameters of the controller are also in a sliding mode (stable trainer). This study considers the ANFIS structure with first order Sugeno model containing nine rules. Bell shaped membership functions with product inference rule are used at the fuzzification level. Finally the Mamdani fuzzy logic which is depends on adaptive neuro-fuzzy inference systems structure designed. At the transferable stage from ANFIS to Mamdani fuzzy model is adjusted for the membership function of the input value (e, de) and the actual output value (y) of the system could be changed to trapezoidal and triangular functions through tuning the parameters of the membership functions and rules base. These help adjust the contributions of both fuzzy control and variable structure control to the entire control value. The application example, control of a mass-damper system is considered. The simulation has been done using MATLAB. Three cases of the controller will be considered: for backstepping sliding-mode controller, for hybrid controller, and for adaptive backstepping sliding-mode controller. A numerical example is simulated to verify the performances of the proposed control strategy, and the simulation results show that the controller designed is more effective than the adaptive backstepping sliding mode controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 2002.10a
• /
• pp.105.6-105
• /
• 2002

Contents 1We developed a new type of lower part of the human-sized BWR (biped walking robot) driven by a new actuator based on the ball screw which has high strength and high gear ratio. Each leg of the robot is composed of three pitch Joints and one roll joint. In all, a 8 degree-of-freedom robot was developed. A new type of actuator for the robot is proposed, which is composed of four bar link mechanism driven by the ball screw. The BWR was designed to walk autonomously by adapting small DC motors for the robot actuators and has an embeded controller system including host computer, batteries and motor drivers. In the performance test, we had basic stable walking data so far, but we f...

• Journal of the Korean Society for Precision Engineering
• /
• v.20 no.6
• /
• pp.55-61
• /
• 2003

Control of multi-link robot arms is a challenging and difficult problem because of the highly nonlinear dynamics. Independent joint adaptive scheme is developed for control of robot manipulators based on Sugeno-type of fuzzy logic. Fuzzy logic system is used to approximate the coupling forces among the joints, coriolis force, centrifugal force, gravitational force, and frictional forces. The proposed scheme does not require an accurate manipulator dynamic, and it is proved that closed-loop system is asymptotic stable despite the gross robot parameter variations. Numerical simulations for three-axis PUMA robot are included to show the effectiveness of controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 1990.10a
• /
• pp.779-782
• /
• 1990

Recently batch type cold rolling processes have been replaced by continuous annealing type processes for cold rolled sheets of mild steel and high strength steel in order to obtain higher productivity, labor saving. In the continuous annealing line, it is very important to maintain the target steel strip temperature at the exit side of each furnace. The automation system of continuous annealing line is based on a hierachical composition. This paper shows how to preset the set value of furnace temperature control for the heating section in a continuous annealing line. Saying in other words, this paper presents the development of an adaptive control approach to control the exit strip temperature in the continuous annealing line. There are three parts in this approach; one is a process modelling and another is recursive parameter estimation and the other is a design of temperature controller.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.3
• /
• pp.243-250
• /
• 2002

Semi-active control devices have received significant attention in recent Years because they offer the adaptability of active-control devices without requiring the associated large power sources. Magnetorheological(MR) dampers are semiactive control devices that use MR fluids to produce controllable dampers. This paper applies sliding mode control method using target variation rate of Lyapunov function for the control of structures by use of MR dampers. The three-story building model under earthquake excitation is analyzed by installing a MR damper in the first-story. The performance of semi-active controllers designed by clipped-optimal algorithm and modified sliding mode control algorithm is compared to the performance of passive-type MR dampers. The results indicate that semi-active controllers achieve a greater reduction of responses than passive-type system and especially the controller by modified sliding mode control method shows a good applicability in the view of response control and control force.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.1
• /
• pp.100-112
• /
• 1996

This paper presents a design experience of a control language for coordination of a multi-robot system. To effectively program job commands, a Petrinet-type Graphical Robot Language(PGRL) is proposed, where some functions, such as concurrency and synchronization, for coordination among tasks can be easily programmed.In our system, the proposed task commands of PGRL are implemented by employing formal model languages, which are composed of three modules, sensory, data handling, and action module. It is expected that by using our proposed PGRL and formal languages, one can easily describe a job or task, and hence can effectively operate a complex real-time and concurrent system. The control system is being implemented by using VME-based 32-bit microprocessor boards for supervisory, each module controller(arm, hand, leg, sensor data processing module) and a real time multi-tasking operating system(VxWorks). (author). 17 refs., 16 figs., 2 tabs.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10a
• /
• pp.445-449
• /
• 1993

The role of a robot becomes more important as factory automation is widely spread in the manufacturing industry. An off-line program system has been required for uninterruption of production lines because it can save cost and time spent in adjusting a robot to a new workcell. The objective of this paper is to develop our own OLP system for a SCARA type FARA robot with four axes. Three-dimensional graphic results are presented for the case when the robot is simulated using the computed torque method with a PD controller and the continuous path trajectory planning.

• 제어로봇시스템학회:학술대회논문집
• /
• 1987.10a
• /
• pp.770-775
• /
• 1987

In this paper, design and development experiences of a vision based robotic assembly system for electronic components are described. Specifically, the overall system consists of the following three subsystems each of which employs a 16 bit Preprocessor MC 68000 : supervisory controller, real-time vision system, and servo system. The three microprocessors are interconnected using the time shared common memory bus structure with hardwired bus arbitration scheme and operated as a master-slave type in which each slave is functionally fixed in view of software. With this system architecture, the followings are developed and implemented in this research; (i) the system programming language, called 'CLRC', for man-machine interface including the robot motion and vision primitives, (ii) real-time vision system using hardwired chain coder, (iii) the high-precision servo techniques for high speed de motors and high speed stepping motors. The proposed control system were implemented and tested in real-time successfully.