• 전자공학회논문지A
• /
• 제33A권6호
• /
• pp.32-41
• /
• 1996

We propose the improved GMSK (gaussian-filtered minimum shift keying) quadrature modulator using the FIR(finite impulse response )filter whose coefficients are obtained form the differnce of phase response, and design its ASIC (applicaton specific integrated circuit) which can be used for GSM (global system for mobile communication) digital cellular system and DCS 1800 (digital cellular system at 1800MHz) personal communication system. Input data become quantized I and Q channel 10 bit signal through cosine and sine ROM mapping after being filtered by the FIR filter whose normalized bandwidth is 0.3 and designed by considering intersymbol interference as well as sampling ratio. These two signals become the GMSK modulated I and Q channel signal through DAC (digital-to-analog converter) and 7th order analog chebyshev LPF(low pass filter) respectively. The difference between the ideal analog signal and its digitized signal is analyzed in terms of sampling noise, quantization noise, truncation noise and coefficient noise. And the effect of the LPF following the DAC is considered. The ASIC design of the GMSK quadrature modulator is also confirmed by an experiment.

• 대한기계학회논문집A
• /
• 제23권7호
• /
• pp.1129-1138
• /
• 1999

[$Moir\acute{e}$] technique is now being extensively investigated as a fast non-contact means of three-dimensional profile measurement especially for reverse engineering. One problem with $moir\acute{e}$ technique is so called $2\pi$-ambiguity problem that limits the maximum step height difference between two neighboring sampling points to be less than half the equivalent wavelength of $moir\acute{e}$ fringes. In this investigation, a new two-wavelength scheme of projection $moir\acute{e}$ topography is proposed and tested to cope with the $2\pi$-ambiguity problem. Experimental results are discussed to assess the new method in measuring large objects with high step discontinuities.

• Journal of Electrical Engineering and Technology
• /
• 제12권5호
• /
• pp.1754-1763
• /
• 2017

This paper analyses the characteristics of incomplete-journey double-circuit transmission lines on the same tower formed by single-circuit lines and double-circuit lines, and then presents a fault location algorithm based on identification of fault branch. With the relationship between the three-phase system and the double-circuit line system, a phase-mode transformation matrix for double-circuit lines can be derived. Based on the derived matrix, the double-circuit lines with faults can be decoupled, and then the fault location for an incomplete-journey double-circuit line is achieved by using modal components in the mode domain. The algorithm is divided into two steps. Firstly, the fault branch is identified by comparing the relationships of voltage amplitudes at the bonding point. Then the fault location, on the basis of the identification result, is calculated by using a two-terminal method, and only the fault distance of the actual fault branch can be obtained. There is no limit on synchronization of each terminal sampling data. The results of ATP-EMTP simulation show that the proposed algorithm can be applied within the entire line and can accurately locate faults in different fault types, fault resistances, and fault distances.

• 전력전자학회논문지
• /
• 제21권2호
• /
• pp.168-174
• /
• 2016

In this paper, current control using PI controller in the synchronous reference frame is analyzed through the relationship among bandwidth, resonance frequency, and sampling frequency in the grid-connected inverter with LCL filter. Stability is investigated by using bode plot in frequency domain and root locus in discrete domain. The feedback variable is the grid current, which is regulated by the PI controller in the synchronous reference frame. System delay is modeled as 1.5Ts, which contains computational and PWM modulator delay. Two resonance frequencies are given at 815 Hz and 3.16 kHz from LCL filter parameters. Sufficient phase and gain margins can be obtained to guarantee stable current control, in case that resonance frequency is above one-sixth of the sampling frequency. Unstable current control is performed when resonance frequency is below one-sixth of the sampling frequency. Analysis results of stability from frequency response and discrete response is the same regardless of resonance frequency. Finally, stability of current control based on theoretical analysis is clearly verified through simulation and experiment in grid-connected inverters with LCL filter.

• 한국대기환경학회지
• /
• 제14권2호
• /
• pp.117-132
• /
• 1998

The main purposes of this study are to investigate the distributional characteristics of polycyclic aromatic hydrocarbons (PAH) in the vapor and particulate phases in the ambient atmosphere, and to evaluate the effect of ambient temperature on the vapor-particle partitioning during the sampling period. A total of 64 samples were collected during a period of 1995 to 1996, using a medium-volume sampler with XAD-2 adsorbents and quartz fiber filters. Analyses of PAH were carried out using HPLC with UV and Fluorescence detections. In this study, a significant seasonal variation in the distributions was observed, reflecting the effect of ambient temperature on the vapor-particle partitioning of PAH. The relationship between the vapor-particle distributions of the 3 to 5 rings PAH and ambient temperature is considered to be well described using the Langmuir adsorption concept. The estimated empirical constants for each PAH in the relationship, particularly for the more volatile compounds, were also comparable with results from other studies. However, it is still difficult to accurately estimate the initial vapor-particle distribution of PAH in the ambient air, since it is not known to what extent the trapped vapours originated from the particles laden in the filter by being volatilized or from the air samples initially present in the vapour phase. The distribution factors for volatile PAH with 3 to 4 rings appeared to be comparable with those in the literature. It should be noted, however, that these distribution factors give information only about the distribution of PAH between the two phases under a specific sampling condition, and hence may provide only semi -quantitative information on the vapor-particle distributions in the atmosphere.

• 한국대기환경학회지
• /
• 제7권1호
• /
• pp.1-16
• /
• 1991

본 연구에서는 대기중 저농도 수준의 다환방향족탄화수소(PAH) 농도를 측정하기 위하여 이들의 포집과 분석방법을 평가하였다. PAH의 포집매체로서 기체상은 Tenax 흡착제를, 입자상은 PTEE 및 유리섬유필터를 이용하였으며 양자 모두 저유량샘플러에 의해 포집되었다. 필터 및 흡착제에 함유된 유기성분은 Soxhlet 장치로 추출하였으며 신속하고도 간편한 Silica 미니칼럼을 이용하여 PAH 함유성분을 분리하였다. PAH 성분은 역상 HPLC로 분리되어 형광 및 UV 검출기로 검지하였다. 분석은 환경보건학적 중요성을 갖는 18개의 PAH에 대하여 행하여졌다. 분석방법의 타당성을 검토하기 위하여 추출능(시료의 회수율), 시료의 전처리단계, HPLC 분리능과 재현성 및 검출한계치 등이 평가되었으며 이울러 서로 다른 포집매체의 이용에 따른 회수율의 영향도 비교 검토되었다. 본 연구에서 채택된 포집 및 분석방법을 실제 환경시료에 적용하여 가스상 및 입자상 PAH 분석을 위한 실례를 제시하였다.

• 전기학회논문지P
• /
• 제58권4호
• /
• pp.391-396
• /
• 2009

In this paper, a control algorithm for DC-Link voltage unbalancing compensation of a four-switch inverter for a three-phase BLDC motor drive is proposed. Compared with a conventional six-switch inverter, the split source of the four-switch inverter can be obtained by splitting DC-link capacitor into two capacitors to drive the three phase BLDC motor. The voltages across each of two capacitors are not always equal in steady state because of the unbalance in the impedance of the DC-link capacitors $C_1$ and $C_2$ or the variable current flowed into the capacitor's neutral point in motor control. Despite the unbalance, if the BLDC motor may be run for a long time the voltage across one of the capacitors is more increased. So the unbalance in the capacitors voltages will be accelerated. As a result, The current ripple and torque ripple is increased due to the fluctuation of input current which flows into 3-phase BLDC motor. According to that, the vibration of motor will be increased and the whole system will be instable. This paper presents a control algorithm for DC-Link voltage unbalancing compensation. The sampling from the voltages across each of two capacitors is used to perform the voltage control of DC-Link by using the feedforward controller.

• Journal of Power Electronics
• /
• 제5권3호
• /
• pp.233-239
• /
• 2005

In this paper, a new conceptual circuit configuration of a 3-phase voltage source, soft switching AC-DC-AC converter using an IGBT module, which has one ARCPL circuit and one ARDCL circuit, is presented. In actuality, the ARCPL circuit is applied in the 3-phase voltage source rectifier side, and the ARDCL circuit is in the inverter side. And more, each power semiconductor device has a novel clamp snubber circuit, which can save the power semiconductor device from voltage and current across each power device. The proposed soft switching circuits have only two active power semiconductor devices. These ARCPL and ARDCL circuits consist of fewer parts than the conventional soft switching circuit. Furthermore, the proposed 3-phase voltage source soft switching AC-DC-AC power conversion system needs no additional sensor for complete soft switching as compared with the conventional 3-phase voltage source AC-DC-AC power conversion system. In addition to this, these soft switching circuits operate only once in one sampling term. Therefore, the power conversion efficiency of the proposed AC-DC-AC converter system will get higher than a conventional soft switching converter system because of the reduced ARCPL and ARDCL circuit losses. The operation timing and terms for ARDCL and ARCPL circuits are calculated and controlled by the smoothing DC capacitor voltage and the output AC current. Using this control, the loss of the soft switching circuits are reduced owing to reduced resonant inductor current in ARCPL and ARDCL circuits as compared with the conventional controlled soft switching power conversion system. The operating performances of proposed soft switching AC-DC-AC converter treated here are evaluated on the basis of experimental results in a 50kVA setup in this paper. As a result of experiment on the 50kVA system, it was confirmed that the proposed circuit could reduce conduction noise below 10 MHz and improve the conversion efficiency from 88. 5% to 90.5%, when compared with the hard switching circuit.

• Journal of Electrical Engineering and Technology
• /
• 제10권5호
• /
• pp.2205-2210
• /
• 2015

Experimental studies have been carried out to study the principle operation of the conductive type wire-mesh tomography sensor and analyse the wire-mesh tomography sensor for the liquid/gas two-phase flow interface and void fraction distribution in a process column. The measurement of the two-phase flows in the process column is based on the cross-sectional local instantaneous conductivity. The sensor consists of two planes of parallel electrode wires with 16 electrodes each and was placed orthogonally with each plane. The sensor electrode wires were made of tinned copper wire with an outer diameter of 0.91 mm which stretched over the sensor fixture. Therefore, this result in the mesh grid size with 5.53×5.53mm². The wire-mesh sensor was tested in a horizontal liquid/gas two-phase flows process column with nominal diameter of 95.6 mm and the sampling frequency of 5882.3529 Hz. The tomogram results show that the wire-mesh tomography provides significant results to represent the void fraction distribution in the process column and estimation error was found in the liquid/gas interface level

• Biomolecules & Therapeutics
• /
• 제11권3호
• /
• pp.178-182
• /
• 2003

The clinical use of once daily aminoglycoside (ODA) dosing has been increased because of the potential therapeutic advantages of this dosing regimen. To evaluate the optimal sampling times of ODA dosing method in a clinical setting, the study was prospectively conducted in a total of 28 patients with UTI. All of the patients were intravenously administered gentamicin at a dose of 7 mg/kg over 60 minutes and randomly divided into two groups. Blood was collected at 0, 2, and 6 hours in Group A and at 1, 2, and 6 hours in Group B after the end of 1-hour infusion. The pharmacokinetic parameters (Ke, Vd and Cmax) obtained using the 0, 6 hour levels and 2, 6 hour levels in Group A were statistically different while those of 1, 6 hour levels and 2, 6 hour levels in Group B were similar. This finding indicated that the distributional phase of ODA is completed within 1 hour following the end of the I-hour infusion. If we are allowed to collect only two blood samples in ODA considering patients comfort and the analytical cost of drug, the first one should be drawn after 1 hour following the end of infusion to obtain adequate pharmacokinetic information.