• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.1
• /
• pp.55-59
• /
• 1999

The Rapid Expansion of Supercritical fluid Solutions (RESS) process was applied to particles coating. Microcapsules prepared by spray drying were used as the core particles, and two kinds of paraffin were used as the coating materials. Supercritical $CO_{2}$ solutions of paraffin were expanded through the short nozzle into the bed that was fluidized by air. Extraction temperature and pressure were varied at $50~120^{\circ}C$, $150~200\;kg/\textrm{cm}^2$, respectively. The thickness of theoritical coating layer ws measured, and precipitate coating layer on surface was analyzed by using SEM, FT-IR. The release behaviors of $Mg^{2+}$ ions were inspected by atomic absorbance spectrophtometer.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.11a
• /
• pp.35-36
• /
• 2005

An ejector driven by a liquid is a fluid transfer equipment to be used under a poor suction condition, which means that there exists a possibility to occur a cavitation. It is a highly reliable device because it has no movable part in it, that is only a passive equipment. The ejector is an inevitably necessary one to overcome a poor pumping condition and to mix uniformly two fluids, however it has a low efficiency since it requires a pump for its operation. This study is for the development of a new-type liquid ejector with the application of a nozzle shape alteration, which maximize the suction performance of it. which provides the increased competition with the domestic industries. Also, the increased performance opens a new manufacturing method to use a commercial pipes for the production of an ejector, which is based on a trivial loss of a performance. However, this minor loss can be sufficiently compensated by the increased performance of a new-type ejector. Therefore, the developed ejector by this study can considerably reduce the manufacturing time and cost while its performance is largely increased.

• International Journal of Advanced Culture Technology
• /
• v.10 no.3
• /
• pp.295-306
• /
• 2022

The NOx removal performance of the SCR process depends on various factors such as catalytic factors (catalyst composition, shape, space velocity, etc.), temperature and flow rate distribution of the exhaust gas. Among them, the uniformity of the flow flowing into the catalyst bed plays the most important role. In this study, the flow characteristics in the SCR reactor in the design stage were simulated using a three-dimensional numerical analysis technique to confirm the uniformity of the airflow. Due to the limitation of the installation space, the shape of the inlet duct was compared with the two types of inlet duct shape because there were many curved sections of the inlet duct and the duct size margin was not large. The effect of inlet duct shape, guide vane or mixer installation, and venturi shape change on SCR reactor internal flow, airflow uniformity, and space utilization rate of ammonia concentration were studied. It was found that the uniformity of the airflow reaching the catalyst layer was greatly improved when an inlet duct with a shape that could suppress drift was applied and guide vanes were installed in the curved part of the inlet duct to properly distribute the process gas. In addition, the space utilization rate was greatly improved when the duct at the rear of the nozzle was applied as a venturi type rather than a mixer for uniform distribution of ammonia gas.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2977-2982
• /
• 2007

Feedwater heaters of many nuclear power plants have recently experienced severe wall thinning damage, which will increase as operating time progresses. Several nuclear power plants in Korea have experienced wall thinning damage in the area around the impingement baffle - installed downstream of the high pressure turbine extraction steam line - inside number 5A and 5B feedwater heaters. At that point, the extracted steam from the high pressure turbine is two phase fluid at high temperature, high pressure, and high speed. Since it flows in reverse direction after impinging the impingement baffle, the shell wall of the number 5 high pressure feedwater heater may be affected by flow-accelerated corrosion. This paper describes the comparisons between the numerical analysis results using the FLUENT code and the down scale experimental data which effect on disclosing of the shell wall thinning of the high pressure feedwater heaters by porous plate.

• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1287-1289
• /
• 1995

For the analysis of hot gas flow due to arc in puffer type $SF_6$ gas circuit breakers(GCBs), a program has been developed by adding function for arcing to the Fluid-in Cells(FLIC) method, which is often used for a two dimensional compressible flow problems, utilizing a simplified enthalpy flow arc model available for arcing. In this paper, the results of arc modelling for 800kV GCB are presented and compared with that of cold gas flow in the interrupters. It is shown that the nozzle clogging is the dominating factor in the pressure rise of the puffer chamber. It permits to estimate the dielectric strength of interrupters.

• Journal of the Korean Ceramic Society
• /
• v.25 no.4
• /
• pp.397-407
• /
• 1988

Spinel, mullite and cordierite powders have synthesized from Mg(NO3)2.6H2O, Al(NO3).9H2O and SiCl4 solution by spray pyrolysis method. The two-fluid nozzle was used as an atomizer. The powders of sinel and mullite were synthesized above 80$0^{\circ}C$, but the cordierite composition was noncrystalline for all synthersizing temperature. Those noncrystalline powders were crystallized to $\alpha$-cordierite during calcining at 130$0^{\circ}C$ for 2hrs. The synthesized spinel, mullite and cordierite powders seem to be consisted of agglomerated hollow spherical particles. For all powders, the particle size ranged from submicron to about 3${\mu}{\textrm}{m}$ and mean particle size was about 1.4${\mu}{\textrm}{m}$ in diameter. The specific surface area values of spinel, mullite and cordierite powders were maximum for powders prepared at 100$0^{\circ}C$, and those were 45.9, 25.8 and 13.6$m^2$/gr, respectively.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2002.04a
• /
• pp.64-64
• /
• 2002

Two dimensional velocity distributions outside a Mach 2.0 supersonic nozzle have been investigated using digital particle image velocimetry (PIV). Mean velocities, turbulence intensities, vorticity field and volume dilatation field are obtained from 300 instantaneous PIV images using 0.33 $\mu\textrm{m}$ $TiO_2$ particle. The seeding particle of larger size, 1.4 $\mu\textrm{m}$ $TiO_2$, is also used for the experimental measurements of velocity lag downstream of shock waves according to particle sizes. The results have been compared and analyzed with schlieren photographs and computational fluid dynamics (CFD) results for the velocity distribution, the locations of shock waves and over-expanded shock structure. It was shown that the locations of normal shock and shock waves can be resolved by the axial or radial velocities, and the velocity lag is more significantly increased due to particle inertia as a particle size increases. And it was also found that over-expanded shock structures call be predicted by volume dilatation fields, and streamwise turbulence intensities are influenced significantly by normal shock waves.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.10a
• /
• pp.308-313
• /
• 2005

실리콘 잉고트의 절단공정에서 발생하는 폐실리콘 슬러지는 실리콘과 실리콘카바이드 등의 유가자원이 함유되어 있으며, 이 중 실리콘 분말은 실리콘 화합물인 알콕시실란 등을 제조하는데 원료로 사용이 가능하다. 본 연구에서는 폐실리콘 슬러지로부터 분리, 합성된 사에 톡시실란(TEOS)을 원료로 이용하여 실리카 나노분말을 합성하였다. TEOS 원료물질을 외부 혼합형 이류체 노즐을 이용하여 미세액적으로 분무하고 화염 속으로 도입시키고 화염열분해 반응을 진행시켜 실리카 나노분말을 합성하였다. 합성된 실리카 나노입자의 특성은 투과형 전자현미경 및 BET에 의하여 입자형상 및 평균 입자크기가 분석되었다. 주요 공정변수인 분산공기의 압력, 반응가스의 조성을 변화시켜 실험한 결과 평균크기가 $9{\sim}68nm$인 실리카 나노분말을 제조하였다.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.6
• /
• pp.51-58
• /
• 2002

The RPV(Reaction Progress Variable) combustion model has been applied to numerically investigate the effects of Damkohler number on the superequilibrium concentration and flame structure in the nonpremixed turbulent flames. Computations are performed for the two turbulent jet flames of CO/H$_2$/N$_2$(40/30/30 volume percent) having the same jet Reynolds number of 16,700 but different nozzle diameters(4.58mm and 7.72mm). The detailed discussions have been made for the interaction between fluid dynamics and chemistry in the flame field.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.3 no.1
• /
• pp.1-10
• /
• 1991

The purpose of this study is to lay groundwork for a complete analysis of two component flow by analyzing a single component flow made of continuous fluid without dispersed phase. In order to achieve uniform velocity distributions which are desirable in designing an optimum spray column direct contact heat exchanger, the influence of injection nozzle orientation has been investigated for axial and radial injections. The results that radial injection ensures more uniform velocity distributions compared to the axial case. The flow characteristics in a spray column have been investigated with various L/D values and inlet velocities, the most uniform internal velocity distributions have been obtained for the case of L/D=10 and 0.1m/sec. In the present investigation, it is shown that radial injection method for the continuous flow is advantageous in obtaining desirable uniform velocity distributions in a spray column. It is also found that as the value of L/D increases and the inlet velocity decreases, the flow improves to be better uniform velocity distributions.