• 한국정밀공학회지
• /
• 제20권6호
• /
• pp.20-26
• /
• 2003

This study proposes the construction of attractor quadrant method for high-precision cutting characteristics evaluation of non-ferrous metals. Also this paper aims to find the optimal cutting conditions of diamond turning machine by measuring surface form and roughness to perform the cutting experiment of non-ferrous metals, which are aluminum, with diamond tool. As well, according to change cutting conditions such as feed rate, using diamond turning machine to Perform cutting Processing, by measuring cutting force and surface roughness and according to cutting conditions the aluminum about cutting properties. Trajectory changes in the attractor indicated a substantial difference in fractal characteristics and attractor quadrant characteristics. In quantitative quadrant feature extraction, 1,309 point in the case of A17075 (one quadrant) and 1,406 point (one quadrant) in the case of brass were proposed on the basis of attractor reconstruction. Proposed attractor quadrant method can be used for high-precision cutting characteristics evaluation of non-ferrous metals.

• Journal of Korean Biological Nursing Science
• /
• 제11권1호
• /
• pp.92-98
• /
• 2009

Purpose: This study was aimed to investigate the colony counts by different disinfecting processes and duration of the operation for humidifiers in an intensive care unit (ICU) in Busan. Method: The four steps of disinfecting process were taken with four different humidifiers according to the use of disinfectant (1:100 $Deconex^{(R)}$ 50FF/nothing) and refilling water (tap water/distilled water). First, the colony counts using water sample from wick was conducted at 0 hr, 24 hr, and 48 hr respectively after turning on the humidifiers. Next, the colony counts using waterdrop from the outlet was done at 0 hr, 24 hr, 48 hr, and 72 hr respectively after turning on the humidifiers. Result: No colony was counted after disinfecting with 1:100 $Deconex^{(R)}$ 50FF until 72 hr after turning on the humidifiers. However, without disinfecting with $Deconex^{(R)}$ 50FF, the colony count was increased in the humidifiers from 24 hr after turning on the humidifiers. The result was the same regardless of the refilling water. Conclusion: According to the results, the study found that disinfection of humidifiers in the ICUs with 1:100 $Deconex^{(R)}$ 50FF every 72 hr is effective to remove general bacteria.

• Journal of the Optical Society of Korea
• /
• 제19권1호
• /
• pp.13-21
• /
• 2015

In recent years energy consumption has become a main concern for network development, due to the exponential increase of network traffic. Potential energy savings can be obtained from a load-adaptive scheme, in which a day can be divided into multiple time periods according to the variation of daily traffic patterns. The energy consumption of the network can be reduced by selectively turning off network components during the time periods with light traffic. However, the time segmentation of daily traffic patterns affects the energy savings when designing multiperiod logical topology in optical wavelength routed networks. In addition, turning network components on or off may increase the overhead of logical topology reconfiguration (LTR). In this paper, we propose two mixed integer linear programming (MILP) models to design the optimal logical topology for multiple periods in IP-over-WDM networks. First, we formulate the time-segmentation problem as an MILP model to optimally determine the boundaries for each period, with the objective to minimize total network energy consumption. Second, another MILP formulation is proposed to minimize both the overall power consumption (PC) and the reconfiguration overhead (RO). The proposed models are evaluated and compared to conventional schemes, in view of PC and RO, through case studies.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1930-1933
• /
• 1991

In this paper, the robustness of self turning controller on the continuous time-delay system is investigated. The polynomial identification method using continuous time exponentially weighted least square algorithm is used for estimating the time.-delay system parameters. The pole-zero and pole placement method are adopted for the control algorithm. On considering the control weighting factor and reliability filter the effect of unmodeled dynamics of the plant are examined by the simulation.

• International Journal of Internet, Broadcasting and Communication
• /
• 제11권4호
• /
• pp.71-75
• /
• 2019

Sleep apnea is a disease that causes various complications, and the polysomnography is expensive and difficult to measure. The purpose of this study is to develop an unrestricted wearable monitoring system so that patients can be examined in a familiar environment. We used a method to detect sleep apnea events and to determine sleep satisfaction by non-constrained method using SpO2 measurement sensor and 3-axis acceleration sensor. Heart rate and SpO2 were measured at the finger using max30100. After acquiring the SpO2 data of the user in real time, the apnea measurement algorithm was used to transmit the number of apnea events of the user to the mobile phone using Bluetooth (HC-06) on the wrist. Using the three-axis acceleration sensor (mpu6050) attached to the upper body, the number of times of tossing and turning during sleep was measured. Based on this data, this algorithm evaluates the patient's tossing and turning during sleep and transmits the data to the mobile phone via Bluetooth. The power source used 9 volts battery to operate Arduino UNO and sensors for portability and stability, and the data received from each sensor can be used to check the various degree between sleep apnea and sleep tossing and turning on the mobile phone. Through thisstudy, we have developed a wearable sleep apnea measurement system that can be easily used at home for the problem of low sleep efficiency of sleep apnea patients.

• 대한교통학회지
• /
• 제12권2호
• /
• pp.47-63
• /
• 1994

The purposes of this study are to identify Traffic Flow characteristics and to develop approach delay model of unsignalized intersection based on the travel speed in the conflicting area. The results of this study are as following ; 1. The cumulative frequency distributions of Left-turning speed show a few differences among approaches and they are distributed to lower range of speeds. On the other hand, those of through speed show obvious differences among bounds. The similar results also show in the analysis of Percentile speed. 2. The effectiveness of conflicting movements to travel speed in the conflicting area are analyzed using regression analysis. Left-turning speed model shows that Left-and Right-Conflicting speed. Through-speed model is also developed, when approaching through volume is less than 420vph. 3. Since the lost time due to the acceleration stop, and decelerlation is occured in the conflicting area, approach delay model is delivered using the travel speed models under the condition of small queuing delay.

• 한국정밀공학회지
• /
• 제13권10호
• /
• pp.154-160
• /
• 1996

The control of diamond turning is usually achieved through a laser-interferometer feedback of slide position. The limitation of this control scheme is that the feedback signal does not account for additional dynamics of the tool post and the material removal process. If the tool post is rigid and the material removal process is relatively static, then such a non-collocated position feedback control scheme may surfice. However, as the accuracy requirement gets tighter and desired surface cnotours become more complex, the need for a direct tool-tip sensing becomes inevitable. The physical constraints of the machining process prohibit any reasonable implementation of a tool-tip motion measurement. It is proposed that the measured force normal to the face of the workpiece can be filtered through an appropriate admittance transfer function to result in the estimated dapth of cut. This can be compared to the desired depth of cut to generate the adjustment control action in additn to position feedback control. In this work, the design methodology on the admittance model-based control with a conventional controller is presented. The recursive least-squares algorithm with forgetting factor is proposed to identify the parameters and update the cutting process in real time. The normal cutting forces are measured to identify the cutting dynamics in the real diamond turning process using the precision dynamoneter. Based on the parameter estimation of cutting dynamics and the admitance model-based nanodynamic control scheme, simulation results are shown.

• 한국자원식물학회지
• /
• 제9권1호
• /
• pp.63-69
• /
• 1996

양파 재배(栽培)에 있어서 기계(機械)를 이용(利用)하여 수확(收穫)의 성력화(省力化)로 노동력(勞動力)과 생산비(生産費)를 절감(節減)하기 위해 본(本) 시험(試驗)을 수행(遂行)한 결과(結果)는 다음과 같다. 1. 기계(機械)를 이용한 양파 굴취수확(掘取收穫)은 관행인력굴취수확(慣行人力掘取收穫)에 비해 트랙터 후부(後部)에 굴취기(掘取機)를 부착(附着)해 서 수확(收穫)한 굴취수확(掘取收穫)이 90-93%로 성력효과(省力效果)는 가장 좋았다. 2. 트랙터 후부(後部)에 굴취기(掘取機)를 부착(附着)한 수확기(收穫機)의 성력효과(省力效果)는 관행인력수확(慣行人力收穫)에 비해 37%의 작업시간(作業時刊)을 절감(節減)하여 37%의 작업비(作業費)를 절멸(節滅)했다.

• 한국정밀공학회지
• /
• 제17권12호
• /
• pp.94-100
• /
• 2000

This paper presents a methodology for In-Process monitoring of tool wear by using ultrasonic sensor in turning operation. An integrated single ultrasonic transducer operation at a frequency of 10MHz is placed in contact with the insert tip. The change in amount of the reflected energy from the nose and flank of the tool can be related to the level of tool wear and the mechanical integrity of the tool. As the results, the tool wear monitoring system based on the ultrasonic pulse-echo method was proposed, it is useful to determine a tool life and tool change time.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1990년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 26-27 Oct. 1990
• /
• pp.170-174
• /
• 1990

The information with regard to the working range of lathe, cutting tool, cutting condition is managed as Database system for turning operation as one part of CAM system. Data with regard to the working range of lathe, cutting tool, cutting condition are stored by the DBMS(Data Base Management System) and can be added, modified, deleted and retrieved for realtime usages. Data stored in Database system are searched to select the most proper cutting tool and cutting condition with the input data fed from the design stage. Codes in regards to tool shape are displayed on graphic mode for easy selection for user and thus presents a good decision support for tool selection. The system developed in this work is operated by the pull down menu on the IBM PC/AT personal computer, or compatible series.