• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.2
• /
• pp.17-23
• /
• 2002

A cylindrical capacitance-type spindle displacement sensor was developed and its effectiveness as a system to monitor cutting forces during hard turning was tested in this research. The sensor was installed between the face of spindle cover and the chucking element and measured pure radial motion of the spindle under the condition with presence of roundness error at measured surface. To prove the effectiveness of the developed system hard aiming tests using ceramic inserts and tool steel as workpiece were conducted. The workpiece was hardened up to 65 Rc. The variations of pure radial motion of the spindle ware measured during the cutting tests. The signals from the sensor showed the same pattern of cutting force variations from the tool dynamometer due to the progress of tool wear. As the flank wear of the ceramic tool increased both static component of cutting forces and the amount of center shift of spindle orbit increased, Results from the research showed that the developed sensor could be utilized as an effective and cheap on-line sensing device to monitor cutting conditions and tool performance in the un-manned machining center.

• Journal of the Korea Convergence Society
• /
• v.11 no.10
• /
• pp.231-236
• /
• 2020

A water reforming reaction high-speed turning incinerator test facility was prepared. The reforming reaction chamber and the combustion chamber were directly connected. The incinerator and dust collecting device were integrated and made into a double bulkhead type air cooling structure. The blower is built into the dust collector to improve spatial efficiency. An axial flow type multi-stage dust collector was applied by collecting dust by using a plurality of dust collecting bins attached to the side of the dust collecting part. As a result of measuring dioxin among the exhausted gases, results below the standard value were obtained. As a result of measuring exhaust gas and heavy metals, results were obtained below the environmental standard.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.5
• /
• pp.37-46
• /
• 2016

In this paper, we propose the beam-steering system using Rotman lens antenna operating at 2.442GHz which is to replace an expensive phase shifter. The overall system consists of the transmission antennas, Rotman lens and switch box. Setting the initial design conditions, it was designed and fabricated satisfying the requirements. From the result tested in the anechoic chamber, it was found that the beam can be steered using Rotman lens in the anechoic chamber. We also visually checked the beam-steering by turning on the LED of the rectenna showing the real-time beam receiving.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.191-194
• /
• 2003

Through using aspheric lens can result in advantages such as an improved optical transfer function, a reduced distortion path or the realization of special image field curvatures. Using the diamond turning method for generating aspherics, the company claim to be able to generate surfaces with a form error of less than $0.33\;{\mu}\;m$ and a surface roughness of less than $0.025\;{\mu}\;m$. In this paper, we are manufacturing thermal image aspheric lens. Thermal image system is electro-optical imaging device which can make visible the difference of infrared energy naturally emitted by objected. In the result of aspherical surface, the form accuracy of about $0.24\;{\mu}\;m$ P-V was obtained and the surface roughness Ra $0.004\;{\mu}\;m$. Also, a brief review of Ultra-precision system Korea photonics technology institute(KOPTI) is present in this paper.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.1
• /
• pp.27-37
• /
• 1993

In unmanned machining, One of the most essential issue is the tool management system which includes controlling. identification, presetting and monitoring of cutting tools. Especially the monitoring of tool wear and fracture may be the heart of the system. In this study a computer vision based tool monitoring system is developed. Also an algorithm which can determine the tool condition using this system is presented. In order to enhance practical adaptability the vision system through which two modes of images are taken is located over the rake face of a tool insert. And they are analysed quantitatively and qualitatively with image processing technique. In fact the morphologies of tool fracture or wear are occurred so variously that it is difficult to predict them. For the purpose of this problem the pattern recognition is introduced to classify the modes of the tool such as fracture, crater, chipping and flank wear. The experimental results performed in the CNC turning machine have proved the effectiveness of the proposed system.

• Journal of Biosystems Engineering
• /
• v.27 no.5
• /
• pp.417-424
• /
• 2002

This study was conducted to develop a vehicle, leading or following a worker at a certain distance to assist laborious transporting works in greenhouses. A prototype vehicle was tested in the practical field conditions using a developed control algorithm. Results of this study were summarized as following: 1. The sensing device consisted of infrared sensors was attached to the front of the vehicle and turning following algorithm was developed to make the vehicle turned as it follows a worker simultaneously. 2. The measured average power consumptions were 110W and 89W, equivalent to 5.2-6.4 hrs battery durations, at low speed with and without the maximum payload, respectively. 3. Results of the travel tests showed that the deviations from the center of row spacing were $\pm$100 mm along the ridge and $\pm$85 mm along the hydroponic bed in the greenhouse. Therefore, the worker-following transport vehicle was feasible to travel along the row without collision in the greenhouse.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.183.1-183.1
• /
• 2016

Due to the latest research trend toward wearable energy devices, transparent and stretchable supercapacitors which can sustain their performance even under physical deformation have steadily attracted huge attention. Despite the Ag NW is the most promising candidate for fabrication of transparent and stretchable electronics, the electrochemical instability interrupts its application to development of the energy device. Here, we introduce a transparent and highly stretchable supercapacitor made by Au-Ag core shell NW network percolation electrode. The Au-Ag core shell NW synthesized by a simple solution process not only shows excellent electrical conductivity but also greatly enhanced chemical and electrochemical stability compare to pristine Ag NW. These outstanding properties of the Au-Ag core shell NW are attributed both to the core Ag NW and the Au protecting sheath layer. The proposed Au-Ag core shell NW based supercapacitor exhibits optical transmittance with outstanding mechanical stability withstanding 60% strain without any decrease of the performance. The supercapacitors connected in series are charged and discharged stable in 30% strain turning on a red LED. These notable results demonstrate the potential of the Au-Ag core shell NW as a strong candidate for development of wearable energy devices.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.5
• /
• pp.435-442
• /
• 2014

This paper describes an improved design model that can be used to configure a non-contact pneumatic device to turn a large sheet at the in-line system. For rotational moving in the conveyor system, the conventional method is to turn the system itself. The improved non-contact pick-up system mainly uses 8 pairs of L-shaped latches and 12 swirl type heads. It is positioned above the upward air flow table. This system performs the non-contact gripping and side-edge contact support in the vertical and rotational directions to hold the self-weight of a large flat sheet. A non-contact air head can exert a sufficient gripping ability at 4N lower than the standard working pressure. The side latches support 60% of the lifting force required. Through structural and flow analysis, the working conditions were simultaneously considered in accordance with the deflection and flatness of the glass.

• Journal of Integrative Natural Science
• /
• v.11 no.1
• /
• pp.44-50
• /
• 2018

In this paper, we propose a context-aware power management (CPM) scheme using beacons to reduce the power consumption of personal computers (PCs). In the proposed CPM scheme, the PC, smartphone, control server, and Internet of Things (IoT) device are necessary. PC users first log in the control server using their smartphones and select PCs to turn on. Then, the selected PCs automatically go into three different modes, i.e., sleep, shutdown, and standby power off modes, in order when the PC users leave the PCs without turning off them. Further, we develop a testbed with the proposed CPM scheme using the Arduino with Bluetooth low energy (BLE) and relay modules. Finally, it is shown that the proposed CPM scheme outperforms the conventional scheme in terms of the power consumption.

• Applied Chemistry for Engineering
• /
• v.32 no.2
• /
• pp.219-223
• /
• 2021

Considering the current COVID 19 pandemic, herein, we developed a material that can be used to fabricate a device for checking the body temperature of a person who has been exposed to influenza or corona virus. This material was formed by mixing pluronic F127 (F127) with a polydiacetylene (PDA) vesicle, which was formed with 10,12-pentacosadiynoic acid. The color of the system started to change from blue to light purple at 37 ℃, finally turning reddish at 40 ℃. Thus, the developed material can be used to detect changes in body temperature, and thus, detect signs of fever. The mixing ratio of the PDA vesicle and F127 was an important factor for controlling the temperature at which the color change started. The results showed that the color change accompanied by the separation of the PDA vesicle with F127. We believe that this phenomenon plays an important role in reducing the conjugation length in the double and triple bond of PDA.