• 한국분말재료학회지
• /
• 제18권4호
• /
• pp.378-384
• /
• 2011

In this research, the indium dissolution properties of the waste LCD panel powders were investigated as a function of milling time fabricated by high-energy ball milling (HEBM) process. The particle morphology of waste LCD panel powders changed from sharp and irregular shape of initial cullet to spherical shape with an increase in milling time. The particle size quickly decreased to 15 ${\mu}m$ until the first minute, then decreased gradually about 6 ${\mu}m$ with presence of agglomerated particles after 5 minutes, which increased gradually reaching a uniform size of 13 ${\mu}m$ consist of agglomerated particles after 30 minutes. The glass recovery, after dissolution, was over 99% at initial cullet, which decreased to 90.1 and 78.6% with increasing milling time of 1 and 30 minute respectively, due to a loss in remaining powder of the surface ball and jar, as well as the filter paper. The dissolution amount of indium out of the initial cullet was 208 ppm before milling, turning into 223 ppm for the mechanically milled powder after 1 minute, and nearly 146~125 ppm with further increase in milling time because of the reaction surface decrease of powders due to agglomeration. With this process, maximum dissolving indium amount (223 ppm) could be achieved at a particle size of 15 ${\mu}m$ with 1 minute of milling.

• 한국항행학회논문지
• /
• 제4권2호
• /
• pp.162-170
• /
• 2000

기동표적의 추적은 실재의 표적 궤적과 기둥의 통계적 특성을 미리 알 수 없기 때문에 매우 어려운 일이다. 이를 해결하기 위한 여러 가지 기법들이 제안되었고 이들 방식은 과거의 고전적인 방법에 비해 상당한 성능향상을 가져왔다. 본 논문에서는 칼만필터를 기본으로 한 회전가속도 추정기를 포함하는 필터를 제안한다. 제안된 방법은 인노베이션(innovation)을 사용하는 입력 추정법과는 달리 기동표적의 궤적의 모양으로부터 직접 가속도 입력벡터를 추정하여 필터를 갱신하는 방식이다. 가속도 모델 칼만필터 및 입력추정 기법(Input estimation)과의 성능을 비교하기 위해 3가지 종류의 기동표적 운동에 대하여 Monte Carlo 시뮬레이션을 수행하고 그 결과를 분석한다.

• 한국대기환경학회지
• /
• 제27권5호
• /
• pp.534-544
• /
• 2011

The secondary aerosol forming potential of ambient air was first measured with the Potential Aerosol Mass(PAM) chamber at Gosan supersite on Jeju island from October 22 to November 5, 2010. PAM chamber is a small flowthrough photo-oxidation chamber with extremely high OH and $O_3$ levels. The OH exposure in the PAM chamber was $(2{\pm}0.4){\times}10^{11}{\sim}(6{\pm}1.2){\times}10^{11}$ molecules $cm^{-3}$ s and was similar to 2 to 5 days of aging in the atmosphere. By periodically turning on and off UV lamps in the PAM chamber, ambient aerosol and newly formed aerosol (e.g. called as PAM aerosol) was alternately measured. Aerosol number and mass concentration in the range of 10~487 nm in diameter was measured by SMPS 3034. With UV lamps on, the nucleation mode particles smaller than 50 nm in diameters were formed. Their number concentration was greater than 105 $cm^{-3}$, leading to increase in aerosol mass by 0~8 ${\mu}gm^{-3}$. The variations of PAM and ambient aerosols were greatly dependent on characteristics of air masses such as precursor concentrations and degree of aging. This preliminary results suggests that PAM chamber is useful to assess the aerosol formation potential of air mass and its impact on the air quality. The further analysis of data with gaseous and particulate measurements will be done.

• 한국위성정보통신학회논문지
• /
• 제11권4호
• /
• pp.10-14
• /
• 2016

우리나라 위성 개발 사업은 국가 안보 차원의 군사 목적과 민간에서 상업 목적의 통신위성 개발로 양분되어져 왔으나, 우리나라 최초 정지궤도의 지구관측 위성인 천리안 위성을 기점으로 위성의 다양한 활용 방안이 제시되고 있다. 기존 위성 사업에서는 선명한 지상 영상이 주 관심사였던 것에 비해 위성 자료를 가공, 고부가가치 정보 생산에 대한 중요성이 제시되고 있다. 특히, 천리안 2호 위성에 탑재되는 환경탑재체는 시각적으로 관찰되지 않는 대기 중 오염물질의 농도를 감시하므로써, 무한한 위성의 활용성을 적절하게 보여주는 사례라고 할 수 있다. 또한, 위성에서 생산되는 자료 활용성은 자료의 적절한 공개와 제공 정책에 크게 영향을 받을 수 밖에 없으며, 광역적인 위성 특성에 따라 현재 국내의 위성 영상은 안보적인 측면으로 인해 접근이 쉽지 않은 측면이 있었으나, 공개될 경우 드러나지 않은 잠재적인 수요가 충분히 존재할 것으로 예상됨에 따라, 안보적인 측면이 약한 위성 자료에 대한 관리 정책에 대한 변화가 필요한 시점이라고 할 수 있다. 본 논문에서는 확대되고 있는 위성 활용 범위에 따라 위성 자료의 공개 현황을 조사하고 환경위성 특성을 고려한 자료 배포 정책 방안에 대해 제시한다.

• 대한조선학회논문집
• /
• 제43권4호
• /
• pp.422-430
• /
• 2006

The horn and movable parts around the gap of the conventional semi-spade rudder are visualized by high speed CCD camera with the frame rate of 4000 fps (frame per second) to study the unsteady cavity pattern on the rudder surface and gap. In addition, the pressure measurements are conducted on the rudder surface and inside the gap to find out the characteristics of the flow behavior. The rudder without propeller wake is tested at the range of $1.0{\leq}{\sigma}_v\;1.6$ and at the rudder deflection angle of $-8{\leq}{\theta}{\leq}10^{\circ}$. The time resolved cavity images are captured and show strong cavitation around the rudder gap in all deflection angles. As the deflection angle gets larger, the flow separated from the horn surface increases the strength of cavitation. The accelerated flow along the horn decreases its pressure and the separated flow from the horn increases the pressure abruptly. The pressure distribution inside the gap reveals the flow moving from the pressure to suction side. In the negative deflection angle, the turning area on the movable part initiates the flow separation and cavitation on it.

• 농업과학연구
• /
• 제42권1호
• /
• pp.63-71
• /
• 2015

Path planning is an essential part for traveling and mowing of autonomous lawn mower tractors. Objectives of the paper were to analyze operation patterns by a skilled farmer, to extract and optimize waypoints, and to demonstrate generation of formatted planned path for autonomous lawn mower tractors. A 27-HP mower tractor was operated by a skilled farmer on grass fields. To measure tractor travel and operation characteristics, an RTK-GPS antenna with a 6-cm RMS error, an inertia motion sensing unit, a gyro compass, a wheel angle sensor, and a mower on/off sensor were mounted on the mower tractor, and all the data were collected at a 10-Hz rate. All the sensor data were transferred through a software program to show the status immediately on the notebook. Planned path was generated using the program parameter settings, mileage and time calculations, and the travel path was plotted using developed software. Based on the human operation patterns, path planning algorithm was suggested for autonomous mower tractor. Finally path generation was demonstrated in a formatted file and graphic display. After optimizing the path planning, a decrease in distance about 13% and saving of the working time about 30% was achieved. Field test data showed some overlap, especially in the turning areas. Results of the study would be useful to implement an autonomous mower tractor, but further research needs to improve the performance.

• 농업과학연구
• /
• 제42권1호
• /
• pp.53-61
• /
• 2015

Development of highly efficient and energy-saving tractors has been one of the issues in agricultural machinery. For design of such tractors, measurement and analysis of load on major power transmission parts of the tractors are the most important pre-requisite tasks. Objective of this study was to perform pre-processing procedures before effective analysis of load data of agricultural tractors (30, 75, and 82 kW) during major field operations such as plow tillage, rotary tillage, baling, bale wrapping, and to select the suitable pre-processing method for the analysis. A load measurement systems, equipped in the tractors, were consisted of strain-gauge, encoder, hydraulic pressure, and radar speed sensors to measure torque and rotational speed levels of transmission input shaft, PTO shaft, and driving axle shafts, pressure of the hydraulic inlet line, and travel speed, respectively. The entire sensor data were collected at a 200-Hz rate. Plow tillage, rotary tillage, baling, wrapping, and loader operations were selected as major field operations of agricultural tractors. Same or different farm works and driving levels were set differently for each of the load measuring experiment. Before load data analysis, pre-processing procedures such as outlier removal, low-pass filtering, and data division were performed. Data beyond the scope of the measuring range of the sensors and the operating range of the power transmission parts were removed. Considering engine and PTO rotational speeds, frequency components greater than 90, 60, and 60 Hz cut off frequencies were low-pass filtered for plow tillage, rotary tillage, and baler operations, respectively. Measured load data were divided into five parts: driving, working, implement up, implement down, and turning. Results of the study would provide useful information for load characteristics of tractors on major field operations.

• 한국병원경영학회지
• /
• 제8권4호
• /
• pp.1-25
• /
• 2003

The wave of globalisation initiated by marketisation has increasingly penetrated into all sectors across the world, accordingly, the health & hospital service sector could not be made no escapes, and it currently faces the order of more marketised competition more than ever. Traditionally, the characteristic of the hospital services in the UK has considered as a model of social provision by government. However, contrary to our knowledge, the sphere of the hospital service in the UK has already been immersed in by the marketisation, in which the private actors have been embedded in order to tweak the activities of the hospital service with in the European Union. As the methodology of this research, the qualitative analysis, namely the interview with some doctors in Surgery, NHS Trusts staffs and relevant specialists in has been performed on April to May, 2003. And on the other hand, the various documents related to its service have been analysed. Thus, this paper will review the characteristics of the health service sector in the UK. In doing so, it will illuminate what would be the structural factors derived from its existing system, as a result, it will shed light on how the UK government makes an effort to resolve the problematic situation by reviewing the policy direction of Foundation Hospital proposed recently. In the next stage, it will analyse how all elements consist of the hospital management in the UK has been adjusted and be likely to be changed within Europe. More specifically focuses on how the private hospital service has been managed and related with the activities of its public hospital service-NHS Trusts. Also, under the circumstance, what private health insurance companies function will be studied. In conclusion, it will be concluded that what will be the implication of Korean hospital service market so as to correspond to globally open market by WTO. Now the UK health service system has faced a turning point of becoming more health care market internally and externally pressed by global and regional factors. Thus it is meaningful to scrutinize how a key part of social provision in the health care market system tends to adjust to globally marketised regulation.

• 한국소음진동공학회논문집
• /
• 제17권8호
• /
• pp.683-692
• /
• 2007

Recently, plastic products in air-intake parts of automotive engines have become very popular due to advantages that include reduced weight, constricted cost, and lower intake air temperature. However, flow-induced noise in air-intake parts becomes a more serious problem for plastic intake-manifolds than for conventional aluminum-made manifolds. This is due to the fact that plastic manifolds transmit more noise owing to their lower material density. Internal aerodynamic noise from an idle speed control actuator(ISA) is qualitatively analyzed by using a scaling law, which is expressed with some flow parameters such as pressure drop, maximum flow velocity, and turbulence kinetic energy. First, basic flow characteristics through ISA passage are identified with the flow predictions obtained by applying computational fluid dynamics techniques. Then, the effects on ISA passage noise of each design factors including the duct turning shape and vane geometries are assessed. Based on these results, the preliminary low noise design for the ISA passage are proposed. The current method for the prediction of internal aerodynamic noise consists of the steady CFD and the scaling laws for the noise prediction. This combination is most cost-effective, compared with other methods, and therefore is believed to be suited for the preliminary design tool in the industrial field.

• 한국치위생학회지
• /
• 제15권4호
• /
• pp.649-659
• /
• 2015

Objectives: The purpose of the study is to investigate the musculo-skeletal pain prevalence and severity in the dental hygienists based on PRECEDE model. Methods: A self-reported questionnaire was completed by 483 dental hygienists in Gwangju from September 13 to October 12, 2013. Data were analyzed by frequency analysis, chi-square test, t-test, and multiple logistic regression analysis using SPSS 18.0 program. Musculo-skeletal pain severity was classified from 1 to 5 by PRECEDE model. The questionnaire consisted of six questions of the general characteristics of the subjects, one question of musculo-skeletal pain prevalence, one question of body part musculo-skeletal pain prevalence, one question of subjective health status, three questions of activities of daily living, six questions of working environment, one question of musculoskeletal system diseases knowledge, two questions of social support, two questions of education experience and data use method, and five questions of necessity of health education. Results: The prevalence rate of musculo-skeletal pain within a year was 83.9% and 22.8% of the dental hygienists complained of severe pain. The odds ratio of moderate pain severity was 1.99(95% CI, 1.10-3.60) and the odds ratio of unhealthiness was 3.27 (95% CI, 1.35-7.94). The odds ratio of pain severity in those working for 4-6 years was 0.21(95% CI, 0.08-0.57). The odds ratio of pain severity in those practicing 6-10 scaling cases per day was 0.33(95% CI, 0.17-0.65). The odds ratio of pain severity in wrist turning and bending was 3.56(95% CI, 1.19-10.62). Conclusions: The muscolu-skeletal pain severity in the dental hygienists was closely associated with subjective health condition, work duration, the number of scaling practice activity, and a treatment posture. Regular physical checkup for the dental hygienists will improve the musculo-skeletal pain due to scaling practice.