• 한국전산유체공학회:학술대회논문집
• /
• 2006.05a
• /
• pp.161-162
• /
• 2006

• Water for future
• /
• v.29 no.4
• /
• pp.187-198
• /
• 1996

A numerical model for unsteady dispersion of horizontal line source in turbulent shear flow is developed. A fractional step finite difference method is used which splits the unsteady two-dimensional advective diffusion equation into the longitudinal advection and the vertical diffusion equations, and solves them alternately for half time intervals by the Holly-Preissmann scheme and the Crank-Nicholson scheme, respectively. The developed numerical model is verified using a semi-analytic solution for steady dispersion in turbulent shear flow. Dispersion of an instantaneous plane source in turbulent shear flow is analyzed using the model. The degree of mixing at the same dimensionless time is almost the same regardless of the friction factor, and the travel distance required to reach a certain degree of mixing is inversely proportional to the square root of the friction factor.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.101-107
• /
• 1998

A three-dimensional multi-phase flow is simulated around a smooth tire. This simulation is conducted by solving Navier-Stokes equation with a k-$\varepsilon$ turbulent model. The numerical calculations are carried out by modeling a multi-phase free surface flow mixed with air and water at the inlet. The numerical solutions show an intuitively resonable behavior of water around a moving tire. The calculated pressure around the tire surface along the moving direction is presented. The moving velocities of the tire are chosen to be 30, 40, 60, and 70 km/h. The numerically simulated pressures around the tire are compared with existing experimental data. The comparison shows a new possible tool of analyzing a hydroplaning phenomenon for an automobile tire by means of a computational fluid dynamics.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.312-315
• /
• 2008

The flow structure behind circular and elliptical type rings embedded in a cross-flow was investigated experimentally using two-frame particle image velocimetry (PIV). The experiments were performed in a circulating water channel with a test section of 0.35m height ${\times}$ 0.3m width ${\times}$ 1.1m length. PIV measurements were carried out with varying the Reynolds number in the range of 4.5 ${\times}$ $10^2$ - 4.5 ${\times}$ $10^3$. In the present study, turbulent flow structures in the stream-wise direction and span-wise direction were investigated. The mean velocity field distribution was obtained by statistical-averaging instantaneous velocity fields. The spatial distributions of turbulent statistics such as turbulent intensities and turbulent kinetic energy were also investigated.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2471-2476
• /
• 2008

Turbulent flow and heat transfer to water at supercritical pressure flowing in vertical pipes is investigated using direct numerical simulation (DNS). A conservative space-time discretization scheme for variable-density flows at low Mach numbers is adopted in the present study to treat steep variations of fluid properties at supercritical pressure just above the thermodynamic critical point. The fluid properties at these conditions are obtained using PROPATH and used in the form of tables in the simulations. The buoyancy influence induced by strong variation of density across the pseudo-critical temperature proved to play an important role in turbulent flow and heat transfer at supercritical state. Depending on the degree of buoyancy influence, turbulent heat transfer may be enhanced or significantly deteriorated, resulting in local hot spots along the heated surface.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.176-186
• /
• 1996

The phenomena of drag reduction using small quantities of a liner macromolecules has attracted the attention of many experimental investigations. On the other hand drag reduction in two phase flow can be applied to the transport of crude oil, phase change system such as chemical reactor, pool and boiling flow, and to flow with cavitation which occurs pump impellers. But the research on dragreduction in two phase flow is not sufficient. The purpose of the present work is to evaluate the drag reduction by measuring pressure drop, void fraction, mean liquid velocity and turbulent intensity whether polymer additives a horizontal single and two phase system or not. Flow pattern of air-water two phase flow was classified by electrical conductivity probe signal. Velocities and turbulent intensities of signal were measured simultaneously with a Hot-film anemometer.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.5
• /
• pp.618-624
• /
• 1986

Some studies on direct-contact condensation in cocurrent stratified flow of steam and subcooled water were reviewed. Several approaches have been performed to develop the condensation heat transfer coefficient relationshipo. The local Nusselt number is correlated in terms of the local water Reynolds and Prandtl numbers as well as the steam Froude number. In addition, a turbulence-centered model, developed principally for gas absorption in several geometries, is modified by using calculated interfacial paramters for the turbulent velocity and length scales. These approaches result in a fairly good agreement with the data, whereas, the turbulence-centered model is here rexcommened since it is based on the turbulent properties which may be closely related to the condensation phenemena.

• Water Engineering Research
• /
• v.2 no.3
• /
• pp.179-185
• /
• 2001

The time consuming and expensive nature of experimental research on scouring processes caused by flowing water makes it attractive to develop numerical tools for the predication of the interaction of the fluid flow and the movable bed. In this paper the numerical simulation of scour by a wall jet is presented. The flow is assumed to be two-dimensional, and the alluvium is cohesionless. The solution process, repeated at each time step, involves simulation of a turbulent wall jet flow, solution of the convection-diffusion of sand concentration, and prediction of the bed deformation. For simulation of the jet flow, the governing equations for momentum, mass balance and turbulent parameters are solved by the finite volume method. The SIMPLE scheme with momentum interpolation is used for pressure correction. The convection-diffusion equation is solved for sediment concentration. A boundary condition for concentration at the bed, which takes into account the effect of bed-load, is implemented. The time rate of deposition and scour at the bed is obtained by solving the continuity equation for sediment. The shape and position of the scour hole and deposition of the bed material downstream of the hole appear realistic.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.6
• /
• pp.293-300
• /
• 2007

Turbulent boundary layer over an underwater vehicle is formed when it moves underwater and wall pressure fluctuation within the turbulent boundary layer generates flow-induced noise by exciting the elastic hull of the underwater vehicle. One of the methods to reduce this flow noise is to attach a compliant layer on the surface of the vehicle. In order to observe the possibility of noise reduction in the water when the compliant layer treatments are applied on the surface, three types of specimens those are a bare steel plate, a steel plate coated with neoprene and a steel plate with polyurethane coating material are tested at various flow speeds in a low noise cavitation tunnel. This paper presents the results of measurements and analysis of wall pressure fluctuations which is a main source of flow noise, within the turbulent boundary layer on three specimens. Its results could be shown that about 10dB reduction of wall fluctuation pressure at high frequencies was achieved due to the dissipation of turbulent energy by the compliant coating while it makes the turbulent boundary layer thicker and changes the behavior of turbulent flow in the layer.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.1-6
• /
• 2004

Lots of researches were gone already about grooving corrosion mechanism of ERW carbon steel pipe. But there is seldom study for water hammer happened by fluid and acceleration of corrosion rate by incresed flow velocity. Therefore, in this study carried out the analysis based on hydrodynamic and fracture mechanics. Analyzed stress that act on a pipe using ANSYS as a program, and also FLUENT and STAR-CD were used for flow phenomenon confirmation. As the result, fatigue failure is happened by water hammer and corrosion rate was increased because of turbulent flow.