• International Journal of Fluid Machinery and Systems
• /
• v.9 no.2
• /
• pp.137-142
• /
• 2016

Variable Geometry System (VGS) is widely applied to the nozzle vane for the radial inflow turbine constituting automotive turbochargers for the purpose of optimizing the power output at each operating condition. In order to improve the performance of radial turbines with VGS, it is necessary to clarify the influences of the setting angle of nozzle vane on the internal flow of radial turbine. However, the experimental measurements are considered to be difficult for the flow in radial turbines because of the small size and the high rotational speed. In the present study, the numerical calculations were carried out for the flow in the radial turbine at three operating conditions by applying the corresponding nozzle vane exit angles, which were set up in the experimental study, as the inlet boundary condition. The numerical results revealed the characteristic flow behaviors at each operating condition.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.422-427
• /
• 2000

The design of low-solidity vaned diffusers and the effect on the performance of a turbocharger compressor is discussed. The effect of vane number and turning angle was investigated while maintaining a basic design with a leading edge angle of $70^{\circ}$, leading and trailing edge radius ratios of 1.1 and 1.3. All results are compared with those obtained with the standard vaneless diffuser configuration and it was shown that all designs increased and shifted the pressure ratio to reduced flowrates. Despite the low-solidity configuration none of the vane designs provided a broad operating range, and the vane leading edge angle was not main factor that system went into the surge condition. The diffuser of higher trailing edge angle improved the flow range for the compressor to operate at lower flow region.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.3
• /
• pp.381-387
• /
• 2003

Engine noise consists of the noise radiated from an engine structure and noises from engine ancillaries such as a turbocharger fuel injection system, and alternator. The noise of these ancillaries might be incorrectly evaluated in the aspect of the noise contribution to engine noise because the noise reflection effect of their neighbor engine structure is easily ignored. Consequently, noise source identification should be misled. This study investigates the fact that the engine structure located around an alternator reflects alternator noise, and the reflected noise acts as another alternator noise source in a heavy-duty diesel engine. The result shows that the alternator noise can be correctly estimated in engine noise by properly including the noise reflection effect.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.918-922
• /
• 2007

Aero-pulsation noise, generally caused by geometric asymmetry of a rotating device, is considerable source of annoyance in passenger cars using the turbocharged diesel engine. Main source of this noise is the compressor wheel in the turbocharger system, and can be reduced by after-treatment such as silencers, but which may increase the manufacturing cost. More effective solution is to improve the geometric symmetry over all, or to control the quality of components by sorting out inferior ones. The latter is more effective and reasonable than the former in view of manufacturing. So, an appropriate discrimination method should be needed to evaluate aero-pulsation noise level at the production line. In this paper, we introduce the accurate method which can measure the noise level of aeropulsation and also present its evaluation criteria. Besides verifying the reliability of a measurement system - a rig test system -, we analyze the correlation between the results from rig tests and those from vehicle tests. The gage R&R method is carried out to check the repeatability of measurements over 25 samples. From the result, we propose the standard specification which can discriminate inferior products from superior ones on the basis of aero-pulsation noise level.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.56-64
• /
• 2015

This study presents a model-based gain scheduling strategy for PI-based EGR controllers. The air-to-fuel ratio is used as an indirect measurement of the EGR rate. In order to cope with the nonlinearity and parameter varying characteristics of the EGR system, we proposed a static gain model of the EGR system using a new scheduling parameter. With the 810 steady-state measurements, the static gain model achieved 0.94 of R-squared value. Based on the static gain of the EGR system, the PI gains were robustly designed using quantitative feedback theory. Consequently, the gains of the PI controller are scheduled according to the static gain parameter of the EGR path in runtime. The proposed model-based gain scheduling strategy was validated through various operating conditions of engine experiments such as setpoint step responses and disturbance rejections.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.659-673
• /
• 2021

This study aims to investigate the impact of the High Pressure Selective Catalytic Reduction system (SCR-HP) on a large marine two-stroke engine performance parameters by employing thermodynamic modelling. A coupled model of the zero-dimensional type is extended to incorporate the modelling of the SCR-HP components and the Control Bypass Valve (CBV) block. This model is employed to simulate several scenarios representing the engine operation at both healthy and degraded conditions considering the compressor fouling and the SCR reactor clogging. The derived results are analysed to quantify the impact of the SCR-HP on the investigated engine performance. The SCR system pressure drop and the cylinder bypass valve flow cause an increase of the engine Specific Fuel Oil Consumption (SFOC) in the range 0.3-2.77 g/kWh. The thermal inertia of the SCR-HP is mainly attributed to the SCR reactor, which causes a delayed turbocharger response. These effects are more pronounced at low engine loads. This study supports the better understanding of the operating characteristics of marine two-stroke diesel engines equipped with the SCR-HP and quantification of the impact of the components degradation on the engine performance.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.105-110
• /
• 2011

Through this study, the performance evaluation on the addition of low-pressure loop EGR(Exhaust Gas Recirculation) in a 6.0 L commercial diesel engine was carried out using WAVE modeling and simulation. Since the key technology of advanced diesel engine combustion such as low-temperature combustion is to steadily supply high rates of EGR in a wide operating range, the current study could be effectively contribute to the design and development processes of up-to-date diesel engine systems as real-world reference data. The current simulation results show that the system in which low-pressure loop EGR is added shows almost 2.3 times increase in maximum EGR rate at 1000 rpm as well as almost 1.6 times increase at 2200 and 1600 rpm in comparison with an engine system employing high-pressure loop EGR only. Also, both turbocharger axis speed and charging pressure level did not deteriorate due to the addition of low-pressure loop EGR at 2200 and 1000 rpm, but they were fairly decreased at 1600 rpm.

• Journal of Power System Engineering
• /
• v.5 no.2
• /
• pp.13-21
• /
• 2001

Diesel emission control is being addressed worldwide to help preserve the global environment. This paper mainly deals with the effects of oxidation catalysts to reduce emissions from the automotive heavy-duty diesel engine. Two types of the oxidation catalyst with different kinds of precious material were used. An 11 litter displacement diesel engine with turbocharger was operated to evaluate DOC with various engine speed, load conditions under D-13 mode cycle. We could propose the detail emission data of an automotive heavy-duty diesel engine and the characteristics of the conversion efficiency of the DOC under the D-13 mode. It was found that the mean conversion efficiencies of CO and THC were 49.7% and 61% under the D-13 mode test, respectively.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.166-173
• /
• 2006

This study investigates a heavy duty diesel engine with swept vol. 12.6L, 4cycle-OHC type to verify the effects of the performance and exhaust gas emission according to the variable specifications of both swirl ratio and flow coefficient in inlet port, combustion bowl and fuel injection system. To meet the high BMEP and stringent exhaust emission standard, a turbocharger with wastegate and an intercooler were installed in the engine. Helical port, major design parameters for combustion chamber and electronic fuel injection pump with 1,000bar were reviewed and applied. Confirmation tests were also performed to meet the target value, $NO_x$ 5.0g/kWh and PM 0.1g/kWh of Euro3 exhaust emission legislation. The results of this study show that not only is it effective to use a relatively bigger bowl size for controlling rapid burning condition due to the decreased in-bowl swirl, but also to use a concave cam with double injection rates to decrease $NO_x$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.1
• /
• pp.47-52
• /
• 2016

Miller timing is one of the promising ways which can improve the fuel consumption of internal combustion engines. Indeed, Miller timing employing an early intake valve close is widely applied to large diesel and gas engines to enhance performance and reduce NOx emissions. In this study, performance evaluation is carried out by 1-D cycle simulation in order to estimate the effect of Miller CAM timing before BDC for a 32 L turbocharged diesel engine. To optimize Miller CAM timing, a single stage turbocharger is matched with an early intake valve close since boost pressure is a significant parameter that can control compression work in a turbocharged engine. The engine simulation result shows that there is enough potential to improve fuel consumption rate and also reduce NOx emissions at the same time.Abstract here.