• Journal of the Korean Geotechnical Society
• /
• v.16 no.5
• /
• pp.117-127
• /
• 2000

터널 시공과 굴착과정에서 파쇄대, 절리, 연약대, 균열 등 암반에서의 불연속면은 중요한 역할을 한다. 본 연구에서는 지반 고유의 특징인 불확실성에 의한 터널 설계와 시공 과정에서 겪는 많은 시행오차를 최소화하기 위해서 국내의 터널 붕락 현장의 지반조사 자료를 분석하여 터널 붕락 유형 및 규모를 제시할수 있는 Geo-predict 시스템을 개발하였다. Geo-predict 시스템은 총 104개 터널 붕괴/붕락자료(국외84개, 국내20개)를 분석한 자료를 테이터베이스로 인공신경망 학습을 토해서 터널 붕괴 형태와 규모를 추론하는 시스템이다. 본 논문에서는 Geo-predict의 개발과정 및 구성.기능을 소개하였으며 104개 터널 현장 자료를 지반조건별로 분석하고 이를 데이터베이스화하여 인공신경함을 이용한 추론 시스탬을 구축하고, 2개 고속전철 터널현장과 1개 지하철 시공현장에 적용성 평가를 실시하여, 터널의 붕락 가능 및 붕락 규모를 추론하였다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.41-48
• /
• 2001

In this study, two factors are simultaneously considered for assessing tunnel face stability: one is the effective stress acting on the tunnel face calculated by upper bound solution; and the other is the seepage force calculated by numerical analysis under the condition of steady-state groundwater flow. The seepage forces calculated by numerical analysis are compared with the results of a model test. From the results of derivations of the upper bound solution with the consideration of seepage forces acting on the tunnel face, it could be found that the minimum support pressure for the face stability is equal to the sum of effective support pressure and seepage pressure acting on the tunnel face. Also it could be found that the average seepage pressure acting on the tunnel face is proportional to the hydrostatic pressure at the same elevation and the magnitude is about 22% of the hydrostatic pressure for the drainage type tunnel and about 28% for the water-proof type tunnel. The model tests performed with a tunnel model had a similar trend with the seepage pressure calculated by numerical analysis. From the model tests it could be also found that the collapse at the tunnel face occurs suddenly and leads to unlimited displacement.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.20 no.3
• /
• pp.543-560
• /
• 2018

With the increased development in downtown underground space facilities that vertically cross under a railway at a shallow depth, the demand for non-open cut method is increasing. However, most construction sites still adopt the pipe roof method, where medium and large diameter steel pipes are pressed in to form a roof, enabling excavation of the inside space. Among the many factors that influence the loosening region and loads that occur while pressing in steel pipes, the size of the pipe has the largest impact, and this factor may correspond to the magnitude of load applied to the underground structure inside the steel pipe roof. The super equilibrium method (SEM) has been developed to minimize ground disturbance and loosening load, and uses small diameter pipes of approximately 114 mm instead of conventional medium and large diameter pipes. This small diameter steel pipe is called an SEM pile. After SEM piles are pressed in and the grouting reinforcement is constructed, a crossing structure is pressed in by using a hydraulic jack without ground subsidence or heaving. The SEM pile, which plays the role of timbering, is a fore-poling pile of approximately 5 m length that prevents ground collapse and supports surface load during excavation of toe part. The loosening region should be adequately calculated to estimate the spacing and construction length of the piles and stiffness of members. In this paper, we conducted a comparative analysis of calculations of loosening load that occurs during the press-in of SEM pile to obtain an optimal design of SEM. We analyzed the influence of factors in main theoretical and empirical formulas applied for calculating loosening regions, and carried out FEM analysis to see an appropriate loosening load to the SEM pile. In order to estimate the soil loosening caused by actual SEM-pile indentation and excavation, a steel pipe indentation reduction model test was conducted. Soil subsidence and soil loosening were investigated quantitatively according to soil/steel pipe (H/D).