• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 추계학술대회 논문집
• /
• pp.202-205
• /
• 2009

Tubular torsion beam of high strength steel is going about in an automotive rear axle due to the advantages of light weight and efficient rear packaging capability. High strength tubular beam can be manufactured by the hydroforming in order to ensure dimensional accuracy, while a conventional stamping has been used for steel tubular beam. Internal pressure, feeding and their combination are the key factors of controlling the process. Based on the numerical simulation and try-outs, the optimized hydroforming process conditions for the high strength tubular beam were suggested.

• Structural Engineering and Mechanics
• /
• 제10권2호
• /
• pp.125-138
• /
• 2000

The paper analyzes the problem of torsion in an adhesive non-tubular bonded single-lap joint. The joint considered consists of two thin rectangular section beams bonded together along a side surface. Assuming the materials involved to be governed by linear elastic laws, equilibrium and compatibility equations were used to arrive at an integro-differential relation whose solution makes it possible to determine torsional moment section by section in the bonded joint between the two beams. This is then used to determine the predominant stress and strain field at the beam-adhesive interface (stress field along the direction perpendicular to the interface plane, equivalent to the applied torsional moment and the corresponding strain field) and the joint's elastic strain (absolute and relative rotations of the bonded beam cross sections). All the relations presented were obtained in closed form. Results obtained theoretically are compared with those given by a three dimensional finite element numerical model. Theoretical and numerical analysis agree satisfactorily.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 추계학술대회논문집
• /
• pp.147-150
• /
• 2005

The torsion beam axle type is widely used in the rear suspension for small passenger car because of low cost, good performance and etc. The FE and dynamic analysis using the computer are very helpful for the efficiency of the torsion beam design. First of all, the reliability on the computational model must be verified for the analysis. In this study, The FE model of the torsion beam was verified according to comparison with he test data. And after making the flexible body using the FE model, the dynamic characteristic of the tubular type torsion beam axles was compared with that of the V-beam type.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.231-232
• /
• 2008

• 소성∙가공
• /
• 제24권1호
• /
• pp.13-19
• /
• 2015

For an accurate analysis of hot stamping, a coupled simulation with different aspects of the process(i.e. mechanical, thermal, and phase transformation) is needed. However, coupled simulations are time consuming and costly. Therefore, the current study proposes a simplified method focused on the forming for the hot stamping simulation of a coupled torsion beam axle (CTBA) tubular beam. In this simplified method, non-isothermal conditions were assumed and only conduction was considered, since it represents the majority of the heat transfer during hot stamping. In addition, temperature and strain rate effects were also included. Moreover, an isothermal simulation was conducted and compared with a non-isothermal simulation. Finally, the simulations were verified by experiments. In conclusion, the proposed method is shown to be effective for the development of tube-type parts, and it effectively predicts the deformation of the tubular beam during hot stamping.

• 소성∙가공
• /
• 제16권3호
• /
• pp.201-209
• /
• 2007

Generally, the forming process of suspension system parts have been considered only considered with the formability and have not been considered with the durability of suspension system. But the durability of suspension system is very important characteristic for the dynamic performance of vehicle. Therefore, the suspension system should be manufactured to consider the durability as well as the formability. This paper is about an optimum forming process design with the effect of section properties to consider the roll durability of torsion beam type suspension. In order to determine the tube hydroforming process for the satisfaction the roll durability, the stamping and hydroforming simulation by finite element method were performed. And the results from finite element analysis and roll durability examination showed the tube hydroforming process of torsion beam is optimized as satisfying the durability performance.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 추계학술대회논문집
• /
• pp.32-35
• /
• 2004

The development of automotive rear chassis part using tube forming process has advantage of increase in part durability and decrease in its weight. We developed tubular type rear CTBA(Coupled Torsion Beam Axle) part with 60K high strength steel developed by POSCO in this project. The result was demonstrated that tubular type CTBA shows excellent durability performance and $10\%$ weight reduction compared with V-beam type CTBA in our work. Furthermore, we will adapt this technology to mass production and apply to the other chassis parts.

• 대한기계학회논문집A
• /
• 제37권3호
• /
• pp.339-344
• /
• 2013

보론강을 사용하는 열간성형은 경량화된 자동차 차체부품의 생산을 위해서 최근에 널리 사용되고 있으며, 열간성형 후 약 1,500 MPa 정도의 고강도 특성을 얻을 수 있다. 그러나 열간성형이 현가부품에 사용되기 위해서는 고강도 특성보다 피로특성이 더 중요해진다. 따라서, 본 연구에서는 열간성형에 의해 제작된 자동차 현가부품의 일종인 튜블러 토션빔 액슬의 피로특성에 대하여 연구하였다. 냉각방식에 따른 보론강의 저주기 피로특성에 대하여 연구하였으며, 튜블러 토션빔 액슬의 피로수명을 예측하기 위해서 구조 및 피로해석이 수행되었다. 튜블러 토션빔 액슬의 토션빔 영역에서 응력집중이 발생하였으며, 열간성형에 의한 고강도화가 튜블러 토션빔 액슬의 수명향상에 큰 영향을 미쳤다.