Wet porous media representing agronomic soil that contains variable water content with variable electrolyte concentration was measured to study the shape of the curves of the electric double layer capacitance versus frequency (from 10 KHz to 10 MHz. This was done in an attempt to find the lowest practical operating frequency for developing low cost dielectric constant soil moisture probes. Cellulose sponge was used as the porous media. A high frequency electronic bridge circuit was developed for measuring the equivalent network parallel resistance and capacitance of porous media. It appears that the effects of the electric double layer component of the total parallel network capacitance essentially disappear at operating frequencies greater than approximately 25 MHz at low electrolyte concentrations but are still important at 50 MHz at higher concentrations. At these frequencies, the double layer capacitance masks the diffusion region capacitance where true water content capacitance values reside. The general shape of the curve of volumetric water content versus porous media dielectric constant is presented, with an empirical equation representing data for this type of curve. It was concluded that the lowest frequency where dielectric constant values which represent true water content information will most likely be found is between 30 and 50 MHz at low electrolyte concentrations but may be above 50 MHz when the total electrolyte concentration is near the upper level required for most mesophyte plant nutrition.
Failure criterion is a parameter to represent the resistance to failure of locally wall thinned pipe, and it depends on material characteristics, defect geometry, applied loading type, and failure mode. Therefore, accurate prediction of integrity of wall thinned pipe requires a failure criterion adequately reflected the characteristics of defect shape and loading in the piping system. In the present study, the finite element analysis was performed and the results were compared with those of pipe experiment to develop a sound criterion for failure of internally wall thinned pipe subjected to combined pressure and bending loads. By comparing the predictions of failure to actual failure load and displacement, an appropriate criterion was investigated. From this investigation, it is concluded that true ultimate stress criterion is the most accurate to predict failure of wall thinned pipe under combined loads, but it is not conservative under some conditions. Engineering ultimate stress estimates the failure load and displacement reasonably for al conditions, although the predictions are less accurate compared with the results predicted by true ultimate stress criterion.
Journal of the Korea Academia-Industrial cooperation Society
/
v.19
no.5
/
pp.263-274
/
2018
In this study, the applicability and external/internal stability of a MSEW abutment with a slab were investigated. Structural analysis of slab bridges between 10 ~ 20.0 m and thicknesses of 0.7 ~ 0.9 m was carried out to calculate the reaction forces due to dead and live loads acting on the bridge supports. The slab bridge with a length of 20.0 m satisfied the allowable contact pressure of 200 kPa for the true MSEW abutment. Because the external stability of the true MSEW abutment was dominated by the geometry of the MSE wall, the change in the factor of safety due to the load of the super-structure is small. Because the stiffness of the foundations is fixed and the load of the super-structure is increased, the factor of safety of the bearing capacity was reduced. As the load of the super-structure was increased, the horizontal earth pressure of the true MSEW abutment increased greatly. As a result, the pullout and fracture of the uppermost reinforcement, which are the factors of safety, did not meet the design criteria. Therefore, it is necessary to increase the pullout resistance and the long-term allowable tensile force of the reinforcement placed on the top of the reinforced soils to ensure efficient design and performance of a true MSEW abutment.
Lee, Ji Hyun;Jang, Kyoung Soo;Lee, Won Jeong;Choi, Yong Ho;Choi, Gyung Ja
Horticultural Science & Technology
/
v.32
no.5
/
pp.673-683
/
2014
This study was conducted to establish an efficient screening method to identify cucurbits resistant to powdery mildew. Powdery mildew fungus was obtained from a single lesion of infected cucumber leaf in 2010 at Daejeon. The fungus was identified as Podosphaera xanthii race 1 based on morphological characteristics and resistance responses of four melon differentials. Development of powdery mildew caused by the fungal isolate on 34 commercial cultivars of cucumber was investigated at three plant growth stages in a greenhouse. The degree of resistance of cotyledons of each cultivar to the fungus was not correlated with that of whole plant, but powdery mildew occurrence in the first true leaf was highly correlated with resistance at the level of the whole plant. Based on these results, the first true leaf of cucurbit cultivars can be used for screening of resistance to powdery mildew. In addition, variation of resistance of commercial 12 cucumber and 26 melon cultivars to the powdery mildew fungus due to different growing seasons was tested. In the case of cucumber, the resistance response in some cultivars was influenced by growing season. The resistant cultivars showed higher resistance in the warm season than in the cool season. By contrast, the resistant melon cultivars demonstrated strong resistance in all the tested growing seasons. Interestingly, the tested powdery mildew pathogen, a member of P. xanthii race 1, was not pathogenic on seven cultivars of watermelon (Citrullus lanatus). To follow up on this, diverse race 1 isolates of P. xanthii should be collected and tested.
Kim, Jung-Woon;Kim, Bong-Joon;Lee, Deug-Woo;Moon, Young-Hoon
Transactions of the Korean Society of Mechanical Engineers A
/
v.26
no.6
/
pp.1120-1126
/
2002
Machining characteristics of tool steels manufactured by electro slag casting process has been investigated in this study. For the estimation of machinability, turning and drilling tests are carried out. The chip shapes at various velocities are investigated for the comparison of turning workabilities of tool steels because the chip shapes reflect characteristics of cutting resistance. In case of drilling test, feed motor currents measured by a hall sensor are used as a measure for the drilling resistance. The machining characteristics of the tool steels are strongly correlated with tensile properties, such as tensile strength, hardness, and ductility. In case of turning workability, it was found to be favoured by the higher tensile strength, while the opposite is true far the drilling workability. The electro-slag casted materials show better turning workability in the viewpoint of chip shapes and, the quenching-tempered electro-slag casted material has relatively better drilling machinability than that of the annealed one.
Thirty four patients with a ventricular septal defect, aged 2 months to 24 years [median 2.33 years], had lung biopsies during open heart procedures to assess the degree of pulmonary vascular disease. The patients were divided into two groups according to their age; group 1 - under 2 years of age [15 patients], and group 2- over 2 years of age [19 patients]. The, pathologic change of the pulmonary arterioles was correlated with pre-operative hemodynamic data in 34 patients. There was no significant correlation between the severity of pulmonary vascular disease according to Heath-Edwards classification and the patients age [X2=1.8381, P=0.1751 ]. There was a significant correlation between degree of medial wall thickness and arteriolar diameter and the level of preoperative peak pulmonary artery pressure and peak systemic artery pressure [Pp/Ps]. Also, there was a good correlation between the preoperative pulmonary vascular resistance and systemic vascular resistance [Rp/Rs]. There was no significant correlation between wall thickness and Pp/Ps, and Rp/Rs below the age of 2 years. We conclude that, in patients over 2 years of age, there was a significant correlation between the medial wall thickness of the pulmonary arteriole and elevation of Pp/Ps and Rp/Rs. This is not true in patients under 2 years of age.
The general pattern of adaptation in the appendicular skeleton with aging is that the subperiosteal apposition of bone occur along with endosteal absorption. This remodeling of diaphysis to a cylinder of larger diameter is hypothesized to serve a mechanical compensatory unction by increasing the moment of inertia as the cortex thins with aging. These findings is only true of the diaphysis of long bone. Measuring the area and inertia at each section of femur, the age-related change of proximal emur and diaphysis is observed. After screening by physical and radiological examination, 200 normal Korean adults divided 5 groups in both male and female based on age. Twenty persons were in each group. One femur in each person was analyzed using CT images. femur scanned with 60 to 80 slices and this images were digitized. Then 2-D images were reconstructed into 3-D images. Using the nonlinear method, normalization and interpolation technique, 7 locations of interest (trochanteric area: 1, 2 subtrochanteric area: 3, 4, isthmic area: 5, 6, 7) were determined. On the each cross section at each location, the area (total, cortical and medullary) and 5 inertia of moment were measured. The results were analyzed statistically. With aging, significant area change occurred mainly in diaphysis and female. In trochanteric area, no significant change was noted. With aging, total and medullary area were increased, but cortical area was not changed. In diaphysis, lateral bendingresistanceincreasedsignificantly. No inertia change was noted in trochanteric area. Anteroposterior bending resistance was constant with aging. In more than age 60, total area and medullary area were larger than that of others. Lateral bending resistance was higher especially in diaphysis. In diaphysis, with aging, the decreased properties is compensated with the increased lateral bending resistance by geometric remodeling. In trochanteric area, no compensation occur. With aging, especially in more than age 60, the higher rate of trochanteric fracture is expected.
This study explores the possibility of finding intersections of commonness and differences between Mahasweta Devi's short stories, "The Hunt" and "Douloti the Bountiful" and Angela Carter's "Flesh and the Mirror" and "Master" in Fireworks. At appearance, Carter as a writer of Great Britains and Devi as a writer of India in postcolonial period do not seem to share any commonness. This study, however, tried to find "common differences," to quote Chandra Mohanty's terminology, as a basis of solidarity possible between these two different feminist writers. Another concept appropriated in this process of comparing Carter and Devi is Gayatri Spivak's 'planetary comparative literature,' which contends the necessity of critical regional studies and the study of Asian Literature in the study of English literature. Devi and Carter, despite their historical, geopolitical and racial differences, share commonness in depicting Asian or colonized women not only as the oppressed others but also as the subjects who show potential for resistance and independence. Carter portrays Japanese women as the colonized and oppressed others of Japanese society, even though Japan did not have any colonial history. Devi finds in the postcolonial Indian women both the oppressed in the interstice of colonial/postcolonial/patriarchal Indian history and the potential for resistance. Despite some limitation in her understanding of Asia, Carter shows her insight to accept Asia as a true origin of her self-knowledge and performativity of her woman's role. Despite their differences, these two writers use Freud's 'unheimlich' from the feminist point of view, in general. Devi's depiction of the heroine's dead body at the end of the story implicates the possibility of resistance through women's 'uncanny' bodies. Carter converts Freudian and negative connotation of woman's body into positive and comfortable 'home' as a starting point of her self knowledge.
Objectives: Epicardial fat is true visceral fat that is known to be associated with metabolic syndrome, high abdominal fat, insulin resistance, coronary artery diseases, low coronary flow reserve and subclinical atherosclerosis. Dampness-Phlegm pattern is one of the pattern diagnosis of traditional Korean medicine. Previous studies showed that Dampness-Phlegm pattern is associated with hypertension, dyslipidemia, metabolic syndrome. This study is intended to find association between Dampness-Phlegm pattern and epicardial fat thickness. Methods: This study was a community-based single center trial. Ischemic stroke patients within 30 days after their ictus were enrolled. Epicardial fat thickness was measured using transthoracic echocardiography. Other measured and obtained variables are medical history, weight, height, body mass index, fasting blood glucose, cholesterol, triglycerol, high density lipoprotein, lipid and low density lipoprotein. Results: Three hundred sixty six were enlisted, and one hundred forty were diagnosed with the Dampness-Phlegm pattern. Dampness-Phlegm pattern group had significantly thicker epicardial fat. Binary logistic regression also showed statistically significant result. Conclusions: This study showed close association between epicardial fat and Dampness-Phlegm pattern. This result suggests a clue to standardization of pattern identification.
Metal oxide/metal bilayer structures are explored as contacts with a low injection barrier in organic thin-film transistors (OTFTs) in an effort to realize their true potential for low-cost electronics. OTFTs with a bilayer electrode of $WO_3$ (10nm) and Al shows a saturation mobility as large as 0.97 $cm^2$/Vsec which are comparable to those of Au-based control samples (~0.90 $cm^2$/Vsec). Scaling of contact resistance with respect to the thickness of $WO_3$ layer is also discussed.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.