• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.11
• /
• pp.980-986
• /
• 2009

In a triple-layered structure of ITO/N,N'-diph enyl-N,N'bis(3-methylphenyl)-1,1' - biphenyl-4,4'-diamine(TPD)/tris(8-hydroxyquinoline)aluminum($Alq_3$)/(2,9-Dimethyl-4,7-diphenyl-1,10-phenanthroline(BCP)/Al device, we have studied the electrical and optical characteristics of organic light-emitting diodes(OLEDs) depending on the deposition condition of BCP layer. Several different sizes of holes on boat and several different deposition rates were employed in evaporating the organic materials. And then, electrical properties of the organic light-emitting diodes were measured and the performance of the devices was analyzed. It was found that the hole-size of crucible boat and the evaporation rate affect on the surface roughness of BCP layer as well as the performance of the device. When the hole-size of crucible boat and the deposition rate of BCP are 1.2 mm and $1.0\;{\AA}/s$, respectively, average surface roughness of BCP layer is lower and the efficiency of the device is higher than the ones made with other conditions. From the analysis of current density-luminance-voltage characteristics of a triple layered device, we divided the conductive mechanism by four region according to applied voltage. So we have obtained a coefficient of ${\beta}_{ST}$ in schottky region is $3.85{\times}10^{-24}$, a coefficient of ${\beta}_{PF}$ in Poole-Frenkel region is $7.35{\times}10^{-24}$, and a potential barrier of ${\phi}_{FN}$ in Fower-Nordheim region is 0.39 eV.

• Progress in Medical Physics
• /
• v.20 no.2
• /
• pp.72-79
• /
• 2009

Scatter correction for I-131 plays a very important role to improve image quality and quantitation. I-131 has multiple and higher energy gamma-ray emissions. Image quality and quantitative accuracy in I-131 imaging are degraded by object scatter as well as scatter and septal penetration in the collimator. The purpose of this study was to estimate scatter and septal penetration and investigate two scatter correction methods using Monte Carlo simulation. The gamma camera system simulated in this study was a FORTE system (Phillips, Nederland) with high energy, general-purpose, parallel hole collimator. We simulated for two types of high energy collimators. One is composed of lead, and the other is composed of artificially high Z number and high density. We simulated energy spectrum using a point source in air. We estimated both full width at half maximum (FWHM) and full width at tenth maximum (FWTM) using line spread function (LSF) in cylindrical water phantom. We applied two scatter correction methods, triple energy window scatter correction (TEW) and extended triple energy window scatter correction (ETEW). The TEW method is a pixel-by pixel based correction which is easy to implement clinically. The ETEW is a modification of the TEW which corrects for scatter by using abutted scatter rejection window, which can overestimate or the underestimate scatter. The both FWHM and FWTM were estimated as 41.2 mm and 206.5 mm for lead collimator, respectively. The FWHM and FWTM were estimated as 27.3 mm and 45.6 mm for artificially high Z and high density collimator, respectively. ETEW showed that the estimation of scatter components was close to the true scatter components. In conclusion, correction for septal penetration and scatter is important to improve image quality and quantitative accuracy in I-131 imaging. The ETEW method in scatter correction appeared to be useful in I-131 imaging.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.4
• /
• pp.431-438
• /
• 2012

The mechanical behavior of the polymeric material, HDPE depends on both time and temperature. The study of the tensile behavior at different strain rates is important in engineering design of the orthopedics device such as X-band plate. The mechanical properties and deformation mechanisms of HDPE are strongly dependent on the applied strain rate. Generally, the deformation behavior of HDPE based on the stress-strain curve is complex because of the highly inhomogeneous nature of plastic deformation, particularly that of necking. Therefore, we attempted to determine the mechanical behavior of HDPE in this study. Normally, tensile testing under various strain rates of the HDPE has been used to determine the mechanical behavior. We performed tensile tests at various strain rates (1 to 500 %/min) to analyze the viscoelastic behavior on increasing the strain rate. A tensile stress-strain curve was plotted from the data, and the point of transition was marked to calculate the transition stress, strain, and modulus.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.11
• /
• pp.1139-1145
• /
• 2011

An automated anastomotic ring-pin system consisting of both the anastomotic ring-pin system and the coupler device has eliminated the drawbacks of the suture method. High density polyethylene (HDPE), a material with outstanding biocompatibility and injection molding capability, was used in the ring. SUS316 stainless steel, Ti-6Al-4Nb, Ti-6Al-4V, and unalloyed titanium were used in FEM simulations of the micropin. The authors categorized the microvascular anastomotic ring micropins into short neck (SN) and long neck (LN) groups in order to evaluate the effect of the micropin's fillet radius and neck length on the von Mises stress. The micropins were further divided into those with and without fillet. On the basis of the fillet radius rate (FRR), which represents the rate of change in the von Mises stress with respect to the availability and shape of the fillet, and the neck length rate (NLR), which represents the rate of change in the von Mises stress with respect to changes in the length of the neck within the fillet shape, it can be concluded that the SN-3 neck design is the most stable.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.102-102
• /
• 2018

Electronic industry had required the finer size and the higher performance of the device. Therefore, 3-D die stacking technology such as TSV (through silicon via) and micro-bump had been used. Moreover, by the development of the 3-D die stacking technology, 3-D structure such as chip to chip (c2c) and chip to wafer (c2w) had become practicable. These technologies led to the appearance of HBM (high bandwidth memory). HBM was type of the memory, which is composed of several stacked layers of the memory chips. Each memory chips were connected by TSV and micro-bump. Thus, HBM had lower RC delay and higher performance of data processing than the conventional memory. Moreover, due to the development of the IT industry such as, AI (artificial intelligence), IOT (internet of things), and VR (virtual reality), the lower pitch size and the higher density were required to micro-electronics. Particularly, to obtain the fine pitch, some of the method such as copper pillar, nickel diffusion barrier, and tin-silver or tin-silver-copper based bump had been utillized. TCB (thermal compression bonding) and reflow process (thermal aging) were conventional method to bond between tin-silver or tin-silver-copper caps in the temperature range of 200 to 300 degrees. However, because of tin overflow which caused by higher operating temperature than melting point of Tin ($232^{\circ}C$), there would be the danger of bump bridge failure in fine-pitch bonding. Furthermore, regulating the phase of IMC (intermetallic compound) which was located between nickel diffusion barrier and bump, had a lot of problems. For example, an excess of kirkendall void which provides site of brittle fracture occurs at IMC layer after reflow process. The essential solution to reduce the difficulty of bump bonding process is copper to copper direct bonding below $300^{\circ}C$. In this study, in order to improve the problem of bump bonding process, copper to copper direct bonding was performed below $300^{\circ}C$. The driving force of bonding was the self-annealing properties of electrodeposited Cu with high defect density. The self-annealing property originated in high defect density and non-equilibrium grain boundaries at the triple junction. The electrodeposited Cu at high current density and low bath temperature was fabricated by electroplating on copper deposited silicon wafer. The copper-copper bonding experiments was conducted using thermal pressing machine. The condition of investigation such as thermal parameter and pressure parameter were varied to acquire proper bonded specimens. The bonded interface was characterized by SEM (scanning electron microscope) and OM (optical microscope). The density of grain boundary and defects were examined by TEM (transmission electron microscopy).

• Journal of Chest Surgery
• /
• v.28 no.5
• /
• pp.453-463
• /
• 1995

During 42 month period 91 consecutive patient underwent coronary artery bypass surgery. The mean age of these patient was 57 years [range from 28 to 78 years . There were 57 men and 34 women. The preoperative risk factors that include beyond the 50 % of total patients were male sex, obesity, hypo-high-density lipoproteinemia, smoking, hypercholesterolemia, hyper-low-density lipoproteinemia, hypertriglyceridemia and hypertension. Preoperatively 27 patients had stable angina pectoris and 39 patients of unstable angina pectoris. Twenty five patients had previous myocardial infarction history. The patterns of disease were 8 patients of single vessel involvement, 18 patients of double vessel involvement, 54 patients of triple vessel involvement and 11 patients of left main coronary artery disease. Fifty five patients were in Canadian Cardiovascular Society functional class III. Myocardial revascularization was performed under emergency conditions in 5 patients. Nine percent of patients had previous PTCA history. We performed 16 cases of sequential anastomosis, internal mammary artery harvest in 86 percent of total patients and total 284 distal anastomoses[mean 3.1 anastomosis per patient . The mean ACC time was 60.5 minutes and ECC time was mean 110 minutes. The combined surgeries were 16 cases of endarterectomy, 2 cases of LV aneurysmectomy, 1 case of Bentall operation, 1 case of repair of sinus of Valsalva, 1 case of ligation of coronary AV fistula and 1 case of excision of breast mass. The most common complication was wound infection[12 cases, 13 % . There was one hospital death due to postoperative respiratory failure and low output syndrome in patient with postinfarction VSD, LV aneurysm. Postoperative 88 patients were in Functional class I or II. The 99mTc-MIBI myocardial perfusion scan that used as evaluation of postoperative state was well correlated with patient`s symptoms instead of some disadvantages.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.425.1-425.1
• /
• 2014

Thermal transport in nanomaterials is not only scientifically interesting but also technological important for various future electronic, bio, and energy device applications. Among the various computation approaches to investigate lattice thermal transport phenomena in nanoscale, the atomistic nonequilibrium Green's function approach based on first-principles density functional theory calculations appeared as a promising method given the continued miniaturization of devices and the difficulty of developing classical force constants for novel nanoscale interfaces. Among the nanometerials, carbon atomic chains, namely the cumulene (all-doulble bonds, ${\cdots}C=C=C=C{\cdots}$) and polyyne (alternation of single and triple bonds, ${\cdots}C{\equiv}C-C{\equiv}C{\cdots}$) can be considered as the extream cases of interconnction materials for nanodevices. After the discovery and realization of carbon atomic chains, their electronic transport properties have been widely studied. For the thermal transport properties, however, there have been few literatures for this simple linear chain system. In this work, we first report on the development of a non-equilibrium Green's function theory-based computational tool for atomistic thermal transport calculations of nanojunctions. Using the developed tool, we investigated phonon dispersion and transmission properties of polyethylene (${\cdots}CH2-CH2-CH2-CH2{\cdots}$) and polyene (${\cdots}CH-CH-CH-CH{\cdots}$) structures as well as the cumulene and polyyne. The resulting phonon dispersion from polyethylene and polyene showed agreement with previous results. Compared to the cumulene, the gap was found near the ${\Gamma}$ point of the phonon dispersion of polyyne as the prediction of Peierls distortion, and this feature was reflected in the phonon transmission of polyyne. We also investigated the range of interatomic force interactions with increase in the size of the simulation system to check the convergence criteria. Compared to polyethylene and polyene, polyyne and cumulene showed spatially long-ranged force interactions. This is reflected on the differences in phonon transport caused by the delicate differences in electronic structure.

• Safety and Health at Work
• /
• v.6 no.1
• /
• pp.30-34
• /
• 2015

Background: The purpose of this study was to examine the cohesions status of the coordination within response teams in the emergency response team (ERT) in a refinery. Methods: For this study, cohesion indicators of social network analysis (SNA; density, degree centrality, reciprocity, and transitivity) were utilized to examine the coordination of the response teams as a whole network. The ERT of this research, which was a case study, included seven teams consisting of 152 members. The required data were collected through structured interviews and were analyzed using the UCINET 6.0 Social Network Analysis Program. Results: The results reported a relatively low number of triple connections, poor coordination with key members, and a high level of mutual relations in the network with low density, all implying that there were low cohesions of coordination in the ERT. Conclusion: The results showed that SNA provided a quantitative and logical approach for the examination of the coordination status among response teams and it also provided a main opportunity for managers and planners to have a clear understanding of the presented status. The research concluded that fundamental efforts were needed to improve the presented situations.

• Korean Journal of Crystallography
• /
• v.7 no.1
• /
• pp.73-80
• /
• 1996

The single crystal growth has been carried out with the newly designed 1-T HB(single temperature zone horizontal Bridgman) system for GaAs crystals of 2 inch diameter doped with Si, Zn or undoped. With this method, incidence probability of single crystallinity was shown to be 0.73. Lattice defects evaluated from EPD(etch pit density) measurement were in the range of 5,000-20,000/cm2, dependent upon the doping condition. For the undoped GaAs crystals, carrier concentrations from the Hall measurement were ∼1×1016/cm3 at the seed part, which were less than half the concentrations of double of triple temperature zone(2-T, 3-T) HB grown crystals. By the 1-T HB method, therefore, GaAs crystals can be grown successfully with better yield and higher purity.

• Fisheries and Aquatic Sciences
• /
• v.26 no.6
• /
• pp.367-379
• /
• 2023

The rapid expansion of shrimp production requires a huge amount of protein sources from soybeans and wild-caught fishmeal; both are becoming a shortage. Meanwhile, catfish production and processing is a giant industry in Vietnam, which produce hundred thousand tonnes of protein- and lipid-rich by-products, annually. Using catfish by-products to gradually replace the traditional protein sources in shrimp aquaculture may bring triple benefits: 1) reducing pressure on wild fish exploitation for fishmeal, 2) reducing the environmental impacts of catfish by-products, and 3) increasing the value and sustainability of aquaculture production. In this study, we used catfish by-products to produce fish protein hydrolysate (FPH) and nano-hydroxyapatite (HA) as additives in feed for Pacific white shrimp (Litopenaeus vannamei). The supplement mixture of FPH and HA was added into the commercial diet (Charoen Pokphand Group [CP], 38% protein, and 6.5% lipid) to reach 38%, 38.5%, 40%, 43%, and 44% of the crude protein content. The survival and growth of shrimps were weekly assessed to day 55. The results showed that the shrimp growth was highest at 43% crude protein content in the feed as indicated by an increase of 124% and 112% in shrimp weight and length, respectively, compared to the commercial reference diet. No negative effects of adding the mixture of FPH and HA on the water quality were observed. Vibrio density was lower than 6.5 × 10³ CFU/mL, which is the lowest Vibrio density negatively affecting the shrimp growth and development. These findings indicate that the mixture of FPH and HA are promising additive components in feed for post-larval shrimp L. vannamei diets.