• Journal of Periodontal and Implant Science
• /
• v.28 no.4
• /
• pp.785-797
• /
• 1998

This study has been done to prove that keratinized gingiva is required for the periodontal health and to analyse the adequate width that is necessary. Until now, the study on frenum has been documented on changing its location. But the location or the formation of the frenum has not been reported. This experiment has used 173 patients from the department of periodontology of Dankook University to investigate the width of keratinized gingiva, the formation of the frenum and its location for the frequency. This study also looks into the relationship between the gingival recession and the structure of the frenum, and affects they have on periodontal health. The width of the keratinized gingiva in the mandible has been found to be highest in the lateral incisor than in the central incisor. The width decreased from the canine to the first premolar until it reached the molar. The interproximal area of the mandibular frenum was 77.9%, which was greater than the frequency (22.1%) from the midline of the teeth. The highest frequency of frenum was at 30.6% in between the both central incisor then second greatest at 20.6% in between the right canine and the right first premolar. Frenum was not found in between the second premolar and the distal area. In the morphology of the frenum, it was found that 43.4% out of 551 parts were found to be a single narrow frenum, and the double or triple ligamented form of the complex frenum were found in similar frequency of 237 parts, but the broad frenum was rarely frequent. The incisal area was popular mostly with the single narrow frenum, the left premolar area frequented 57.4%, and the right premolar frequented 64.7%. Because the distance between the frenum apex and the gingival margin measured to be about 5mm or greater, the frenum apex started in the mucogingival junction and not just below the keratinized gingiva. In the 551 area investigated, 48.3% of gingiva showed recession, incisal area had recession the least at 44.9%, right buccal side at 47.4%, and right buccal side frequented the highest at 52.1%. The teeth that showed recession recessed at the average of 2.151.0.mm and the left canine showed the greatest amount of gingival recession. In the investigation to find out if the keratinized gingiva and the gingiva recession had mutually related somehow, the width of keratinized gingiva showed no affect on the probing depth, but had affected in the gingiva recession. This investigation showed that the gingival recession and the morphology of the frenum related in that, the single narrow frenum had recessed the least and the broad frenum recessed the most. With this analysis, a conclusion was drawn that the morphology of the frenum had affected in the gingical recession.

• Journal of Satellite, Information and Communications
• /
• v.1 no.2
• /
• pp.95-100
• /
• 2006

The COMS(Communication, Ocean and Meteorological Satellite) EPS(Electrical Power Subsystem) is derived from an enhanced Eurostar 3000 version. Eurostar 3000 EpS is fully autonomous operation in nominal conditions or in the event of a failure and provides a high level of reconfigure capability. This paper introduces the COMS EPS preliminary design result. COMS EPS consists of a battery, a solar arrat wing, a PSR(Power Supply Regulator), a PRU(Pyrotechnic Unit), a SDAM(Solar Array Drive Mechanism) and relay and fuse brackets. COMS EPS can offer a bus power capability of 3 kW. The solar array is made of a deployable wing with two panels. One type fo solar cells is selected ad GaAs/Ge triple junction cells. Li-ion battery is base lined with ten series cell module of five cells in parallel. PSR associated to battery and solar array wing generates a power bus fully regulated at 50 V. Power bus os centralized protection and distribution by relay and fuse brackets. PRU provides power for firing actuarors devices. The solar array wing is rotated by the SADM under control of the attitude orbit control subsystem. The control and monitoring of the EPS, especially of the battery, is performed by the PSR in combination with the on-board software.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.19 no.1
• /
• pp.33-38
• /
• 2009

The effect of ${Y_2}{O_3}$ as a sintering additive on thermal conductivity and microstructure of pressureless sintered AIN ceramics was investigated at sintering temperature range from 1,700 to $1,900^{\circ}C$. ${Y_2}{O_3}$ added AIN specimens showed higher densification rate than pure AIN because of the formation of the yttrium aluminates secondary phase by reaction of ${Y_2}{O_3}$ and ${Al_2}{O_3}$ of AIN surface. The thermal conductivity of AIN specimens was promoted by the addition of ${Y_2}{O_3}$ in spite of the formation of secondary phase in AIN gram boundaries and grain boundary triple junction, because ${Y_2}{O_3}$ addition could reduced the oxygen contents in AIN lattice which is primary factor of thermal conductivity. The them1al conductivity of AIN specimens was promoted by increasing sintering time because the increases of average grain size and the elimination of secondary phases from the grain boundary due to the evaporation. Particularly. the thermal conductivity of AIN specimen sintered at $1,900^{\circ}C$ for 5 hours improved over 20 %. $141\;Wm^{-1}K^{-1}$, compared with the specimen sintered at $1,900^{\circ}C$ for 1 hour.

• Journal of Radiation Protection and Research
• /
• v.24 no.1
• /
• pp.45-53
• /
• 1999

Fluorescence in situ hybridization with chromosome-specific probe has been shown to be a valid and rapid method for detection of chromosome rearrangements induced by radiation. This method is useful for quantifying structural aberrations, expecially for stable ones, such as translocation and insertion, which are difficult to detect with conventional method in human lymphocyte. In order to apply FISH method for high dose biological dosimetry, chromosomal abberations by radiation at doses of 1, 3, 5, and 7Gy were analysed with whole chromosome-specific probes by human chromosome 1, 2 and 4 according to PAINT system. The frequencies of stable translocation per cell equivalent were 0.04, 0.33, 1.22, 2.62, and 5.58 for the lymphocyte exposed to 0, 1, 3, 5, and 7Gy, respectively, and those of dicentric were 0.00, 0.06, 0.52, 1.19 and 2.44, respectively. Significantly more translocation of t(Ab), a translocated chromosome with a piece of painted acentric matrial 'b' attached to unpainted piece containing centromere 'A', than reciprocal chromosome t(Ba) was observed. The frequencies of all type of chromosome rearrangements increased with dose. From above result, FISH seemed to be useful for radiation biodosimetry by which the frequencies of various types of stable aberrations in human lymphocyte can be observed more easily than by conventional method and so will improve our ability to perform meaningful biodosimetry.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.143-144
• /
• 2010

3-5족 화합물 반도체를 이용한 집광형 삼중 접합 태양전지는 40% 이상의 광변환 효율로 많은 주목을 받고 있다[1]. 삼중 접합 태양전지의 하부 셀은 기계적 강도가 높고 장파장을 흡수할 수 있는 Ge이 사용된다. Ge위에 성장될 III-V족 단결정막으로서 Ge과 격자상수가 일치하는 GaInP나 GaAs가 적합하고, 성장 중 V족 원소의 열확산으로 인해 Ge과 pn접합을 형성하게 된다. 이때 GaInP의 P의 경우 GaAs의 As보다 확산계수가 낮아 태양전지 변환효율향상에 유리한 얇은 접합 형성이 가능하고, 표면 에칭효과가 적기 때문에 GaInP를 단결정막으로 선택하여 p-type Ge기판 위 성장으로 단일접합 Ge구조 제작이 가능하다. 하지만 이종접합 구조 성장으로 인해 발생한 계면사이의 전위나 미세결함들이 결정막내부에 존재하게 되며 이러한 결함들은 광학소자 응용 시 비발광 센터로 작용할 뿐 아니라 소자의 누설전류를 증가시키는 원인으로 작용하여 태양전지 변환효율을 감소시키게 된다. 이에 결함감소를 통해 소자의 전기적 특성을 향상시키고자 수소 열처리나 플라즈마 공정을 통해 수소 원자를 박막내부로 확산시키고, 계면이나 박막 내 결함들과 결합시킴으로서 결함들의 비활성화를 유도하는 연구가 많이 진행되어 왔다 [2][3]. 하지만, 격자불일치를 갖는 GaInP/Ge 구조에 대한 수소 열처리 및 불순물 준위의 거동에 대한 연구는 많이 진행되어 있지 않다. 따라서 본 연구에서는 Ga0.45In0.55P/Ge구조에 수소 열처리 공정을 적용을 통하여 단결정막 내부 및 계면에서의 결함밀도를 제어하고 이를 통해 태양 전지의 변환효율을 향상시키고자 한다. <111> 방향으로 $6^{\circ}C$기울어진 p-type Ge(100) 기판 위에 유기금속화학증착법 (MOCVD)을 통해 Si이 도핑된 200 nm의 n-type GaInP층을 성장하여 Ge과 단일접합 n-p 구조를 제작하였다. 제작된 GaInP/Ge구조를 furnace에서 250도에서 90~150분간 시간변화를 주어 수소열처리 공정을 진행하였다. 저온 photoluminescence를 통해 GaInP층의 광학적 특성 변화를 관찰한 결과, 1.872 eV에서 free-exciton peak과 1.761 eV에서 Si 도펀트 saturation에 의해 발생된 D-A (Donor to Acceptor)천이로 판단되는 peak을 검출할 수 있었다. 수소 열처리 시간이 증가함에 따라 free-exciton peak 세기 증가와 반가폭 감소를 확인하였고, D-A peak이 사라지는 것을 관찰할 수 있었다. 이러한 결과는 수소 열처리에 따른 단결정막 내부의 수소원자들이 얕은 불순물(shallow impurity) 들로 작용하는 도펀트들이나, 깊은 준위결함(deep level defect)으로 작용하는 계면근처의 전위, 미세결함들과의 결합으로 결함 비활성화를 야기해 발광세기와 결정질 향상효과를 보인 것으로 판단된다. 본 발표에서는 상술한 결과를 바탕으로 한 수소 열처리를 통한 박막 및 계면에서의 결함준위의 거동에 대한 광분석 결과가 논의될 것이다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.102-102
• /
• 2018

Electronic industry had required the finer size and the higher performance of the device. Therefore, 3-D die stacking technology such as TSV (through silicon via) and micro-bump had been used. Moreover, by the development of the 3-D die stacking technology, 3-D structure such as chip to chip (c2c) and chip to wafer (c2w) had become practicable. These technologies led to the appearance of HBM (high bandwidth memory). HBM was type of the memory, which is composed of several stacked layers of the memory chips. Each memory chips were connected by TSV and micro-bump. Thus, HBM had lower RC delay and higher performance of data processing than the conventional memory. Moreover, due to the development of the IT industry such as, AI (artificial intelligence), IOT (internet of things), and VR (virtual reality), the lower pitch size and the higher density were required to micro-electronics. Particularly, to obtain the fine pitch, some of the method such as copper pillar, nickel diffusion barrier, and tin-silver or tin-silver-copper based bump had been utillized. TCB (thermal compression bonding) and reflow process (thermal aging) were conventional method to bond between tin-silver or tin-silver-copper caps in the temperature range of 200 to 300 degrees. However, because of tin overflow which caused by higher operating temperature than melting point of Tin ($232^{\circ}C$), there would be the danger of bump bridge failure in fine-pitch bonding. Furthermore, regulating the phase of IMC (intermetallic compound) which was located between nickel diffusion barrier and bump, had a lot of problems. For example, an excess of kirkendall void which provides site of brittle fracture occurs at IMC layer after reflow process. The essential solution to reduce the difficulty of bump bonding process is copper to copper direct bonding below $300^{\circ}C$. In this study, in order to improve the problem of bump bonding process, copper to copper direct bonding was performed below $300^{\circ}C$. The driving force of bonding was the self-annealing properties of electrodeposited Cu with high defect density. The self-annealing property originated in high defect density and non-equilibrium grain boundaries at the triple junction. The electrodeposited Cu at high current density and low bath temperature was fabricated by electroplating on copper deposited silicon wafer. The copper-copper bonding experiments was conducted using thermal pressing machine. The condition of investigation such as thermal parameter and pressure parameter were varied to acquire proper bonded specimens. The bonded interface was characterized by SEM (scanning electron microscope) and OM (optical microscope). The density of grain boundary and defects were examined by TEM (transmission electron microscopy).

• Journal of the korean academy of Pediatric Dentistry
• /
• v.45 no.4
• /
• pp.455-463
• /
• 2018

The purpose of this study was to evaluate the effect of the intracanal medicaments on the push-out bond strength of the calcium silicate-based materials. Forty extracted single-root human mandibular premolars were sectioned below cementoenamel junction. Standardized root canal dimension was obtained with a parallel post drill. The specimens were randomly divided into a control group (no medicament), and experimental groups received medicaments with either CH (calcium hydroxide), DAP (double antibiotic paste; a mixture of ciprofloxacin and metronidazole), or TAP (triple antibiotic paste; a mixture of minocycline, ciprofloxacin and metronidazole). Following removal of medicaments with irrigation, roots were cut into sections with 1-mm-thickness. Thereafter, calcium silicate-based materials are applied to the specimens : (i) ProRoot MTA$^{(R)}$ and (ii) Biodentine$^{(R)}$. A push-out bond strength was measured and each specimen was examined to evaluate failure mode. Intracanal medication using CH significantly increased the bond strength to the root dentin. But there are no significant differences on the bond strength of ProRoot MTA$^{(R)}$ or Biodentine$^{(R)}$ among TAP, DAP and control groups. The dislodgement resistance of Biodentine$^{(R)}$ from root dentin was significantly higher than that of ProRoot MTA$^{(R)}$ regardless of the type of intracanal medicaments.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.2
• /
• pp.82-88
• /
• 2011

The artificial increase in the solar intensity incident on solar cells using lenses or mirrors can allow solar cells to generate equivalent power with a lower cost. There are two types of concentration optics for solar energy conversion. One is to use mirrors, and the other is to use Fresnel lenses. The gains that can be achieved with a Fresnel lens or a parabolic mirror are compared. The result showed the gains are comparable and the two configurations were developed competitively. In application areas of Fresnel lenses as solar concentrators, several variations of design were devised and tested. Some PV systems still use commercially available flat Fresnel lenses as concentrators. A convex linear Fresnel lens to improve the concentration ratio and the efficiency is devised and flat linear Fresnel lens in thermal energy collection is utilized. In this study, we designed and optimized flat Fresnel lens and the 'light pipe' to develop 500X concentrated solar PV system. In the process, we compare the transmission efficiencies according to groove types. We performed rigorous ray tracing simulation of the flat Fresnel lenses. The computer aided simulation showed the 'grooves in case' has the better efficiency than that of 'grooves out case'. Based on the ray-trace results we designed and manufactured sample Fresnel lenses. The optical performance were measured and compared with ray-trace results. Finally, the optical efficiency was measured to be above 75%. All the design and manufacturing were performed based on that InGaP/InGaAs/Ge triple junction solar cell is used to convert the photon energy to electrical power. Field test will be made and analyzed in the near future.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.5
• /
• pp.310-316
• /
• 2021

Conventional satellites are generally large satellites that are multi-functional and have high performance. However, small satellites have been gradually drawing attention since the recent development of lightweight and integrated electric, electronic, and optical technologies. As the size and weight of a satellite decrease, the barrier to satellite development is becoming lower due to the cost of manufacture and cheaper launch. However, solar panels are essential for the power supply of satellites but have limitations in miniaturization and weight reduction because they require a large surface area to be efficiently exposed to sunlight. Space solar cells must be manufactured in consideration of various space environments such as spacecraft and environments with solar thermal temperatures. It is necessary to study structural materials for lightweight and high-efficiency solar cells by applying an unfolding mechanism that optimizes the surface-to-volume ratio. Currently, most products are developed and operated as solar cell panels for space applications with a triple-junction structure of InGaP/GaAs/Ge materials for high efficiency. Furthermore, multi-layered junctions have been studied for ultra-high-efficiency solar cells. Flexible thin-film solar cells and organic-inorganic hybrid solar cells are advantageous for material weight reduction and are attracting attention as next-generation solar cells for small satellites.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.1
• /
• pp.25-30
• /
• 2007

Proton exchange membrane fuel cell(PEMFC) performance could be affected by various factors such as cell temperature, total pressure, partial pressure of reactants and relative humidity. Hydrogen ion is combined with water to form hydronium ion [$H_3O^+$] and pass through membrane resulting electricity generation. Cooling system is needed to remove heat and other uses on large scale fuel cell. In case that collant conductivity is increased, fuel cell performance could be decreased because produced electricity could be leaked through coolant. In this study, triple distilled water(TDW) and antifreeze solution containing ethylene glycol was used to observe resistance change. Resistance of TDW was taken 28 days to reach preset value, and effect on fuel cell operation was not observed. Resistance of antifreeze solution was not reached to preset value up to 48 days, but performance failure occurred presumably caused by bipolar plate junction resulting stoppage resistance experiment. Generally PEMFC humidification is performed near-saturated operating conditions at various temperatures and pressures, but non-humidifying condition could be applied in small scale fuel cell to improve efficiency and reduce system cost. However, it was difficult to operate large scale fuel cell without humidifying, especially higher than $50{\sim}60^{\circ}C$. In case of small flux such as 0.78 L/min, temperature difference between inlet and outlet was occurred larger than other cases resulting performance decrease. Non-humidifying performance experiments were done at various cell temperature. When both of anode and cathode humidification were removed, cell performance was strongly depended on cell operating temperature.