• 대한조선학회지
• /
• 제8권1호
• /
• pp.29-40
• /
• 1971

In order to study the problem on form factor of hull form, towing test of a full ship model was carried out for different initial trims under both full and half load conditions. The results were fully discussed on the mutual relations among initial trim, mean sinkage and trim change in run, and form factor. There exists optimum initial trim in regard to form factor. Mean sinkage and trim change in run can be expressed in a uninominal approximation in the form of $k_i{\cdot}{F_n}^{2.2}$. The coefficients of this approxmation are related linearly with the initial trim. Form factor changes according to Froude number. It is considered that the trim change in run is a main reason of the fact.

• Coupled systems mechanics
• /
• 제7권2호
• /
• pp.163-176
• /
• 2018

The ship hydrodynamics in static and dynamic states were investigated using 3-dimensional numerical simulations. The static case simulated a fixed ship, while the dynamic case considered a ship with free sinkage and trim using the mesh morphing technique. High speed was found to increase the wave elevation around the ship. Compared with the static case, the dynamic case seemed to generate higher waves near the bow and after the stern. The frictional resistance was found be to more dominant. However, the pressure resistance became gradually important with the increase of the ship speed. The trim and sinkage were also analyzed to characterize the ship hydrodynamics in the dynamic state.

• 한국기계연구소 소보
• /
• 통권9호
• /
• pp.153-167
• /
• 1982

From first-order thin-ship theory, we can obtain the" wave resistance, wave amplitude functions, wave elevation along the hull, sinkage and trim of a ship moving with constant speed into calm water. Generally, these calculations of ship is called with Michell’s Theory, and there is all the difference between calculated wave resistance and residual resistance from conventional wave resis¬tance test. But, these calculated results are important reference materials for initial hull form design procedure. Various calculated results for Shearer’ s Model, Wigley’s Model and Series 60 4210W Model have been calculated using this theory. The results are compared with the corresponding experimental values, and the agreement between theoretical and experimental values is considered satisfactory.

• 대한조선학회논문집
• /
• 제51권6호
• /
• pp.539-547
• /
• 2014

Ship squat is a well known phenomenon, which means an additional sinkage and a change of trim when a ship sails in shallow water. As a series of ship squat study, a HPMM(Horizontal Planar Motion Mechanism) test of KVLCC2 model ship to measure a sinkage and a trim in shallow water was conducted. Additionally a CFD(Computational Fluid Dynamics) analysis was carried out to simulate fluid flows around the ship surface. A change in ship speed, drift angle at three depth conditions(H/T = 1.2, 1.5 & 2.0) is considered for comparing these results. As a result, an increase of the ship speed and the drift angle caused an increase in ship squat in EFD(Experimental Fluid Dynamics), and created a lower pressure on the ship bottom area in CFD. Lastly the sinkage results of KVLCC2 by EFD and CFD are compared to results by three empirical formulas. The tendency of sinkage by EFD and CFD is similar to the results of empirical formulas.

• 해양환경안전학회지
• /
• 제27권3호
• /
• pp.409-420
• /
• 2021

The decrease in under keel clearance (UKC) due to the increase of draft that occurs during advancing and turning of very large vessels of different types was analyzed based on computational fluid dynamics (CFD). The trim change in the Duisburg test case (DTC) container ship was much smaller than that of the KRISO very large crude oil carrier 2 (KVLCC2). The sinkage of both ships increased gradually as the water depth became shallower. The amount of sinkage change in DTC was greater than that in KVLCC2. The maximum heel angle was much larger for DTC than for KVLCC2. Both ships showed outward heel angles up to medium-deep water. However, when the water depth became shallow, an inward heel was generated by the shallow water effect. The inward heel increased rapidly in very shallow water. For DTC, the reduction ratio was very large at very shallow water. DTC appeared to be larger than KVLCC2 in terms of the decreased UKC because of shallow water in advancing and turning. In this study, a new result was derived showing that a ship turning in a steady state due to the influence of shallow water can incline inward, which is the turning direction.

• 수산해양기술연구
• /
• 제44권1호
• /
• pp.68-74
• /
• 2008

This study is concerned with the development of the basic planing hull form of small fishing boat in 25 knots high speed. A series of model test to determine the optimum performance hull form of actual fishing boat with 10 gross tonnage was carried out for 5 models made available planing hull form in the circulation water channel. Model test was performed with the resistance test to study the hydrodynamic characteristics of model ships and the sinkage and trim measurement to investigate the stability of model ships and also the wave pattern observation to analyze the effectiveness of model ships. As the result, the planing hull form of P-4 with deep V type bow can be derived as the best hull form with good performance especially in ship's resistance efficiency showing less residual resistance and sinkage and trim and the spray effect, etc..

• 대한조선학회지
• /
• 제24권2호
• /
• pp.11-19
• /
• 1987

A Series 60, $C_b=0.60$ model was tested in the towing tank of Seoul National University. Total resistance, hull attitude, wake distributions and wave measured at FR condition(free trim and sinkage) and FX condition(fixed trim and sinkage). From the measured data, residual, viscous and wave pattern resistance components were evaluated and compared. It is found that the changes in wetted surface area should be considered in predictions of frictional resistances, and can be easily found from hydrostatic data and measured mean sinkages without additional tests. Applications of the concept to the geosim tests of Series 60, Wigley, Lucy Ashton models show that the conventional extrapolation method can be improved considerably.

• 한국해양공학회지
• /
• 제15권1호
• /
• pp.1-6
• /
• 2001

This study focuses on the potential flow analysis for a hull with the transom stern. The method is based on a low order panel method. The Kelvin type free-surface boundary condition which is known to better fit experimental data for a high speed is applied. To treat a dry transom stern effect a special treatment for the free-surface boundary condition is adopted at the free-surface region after the transom stern. Trim and sinkage, which are important in high speed ships, are considered by an iterative method. Pressure and momentum approaches are used to calculate the wave resistance. Numerical calculations are performed for Athena hull and these results are compared with the experimental data and also other computational results.

• 한국항해학회지
• /
• 제25권4호
• /
• pp.417-422
• /
• 2001

Every ship might be exposed to collision, grounding and/or various accidents. They may make some underwater holes on the hull. An underwater damage would cause her loss of buoyancy, trim, and inclination. Although a ship has some provisions against these accidents, if the circumstance is serious, she would be sunk or upsetted. Because of varieties of type of accidents, one could not prepare all of them. Many subdivision could prevent them, but it is difficult to realize it due to rising costs. This paper deals with physical phenomena of sinkage and an application on box type ship, and some results are earned as follows； 1. sinkage speed up to the level of the damage hole is increased proportionally, and is decreased proportionally after filling the level. 2. the curve of draft shows cup type of second order polynomial up to the damage hole level, and shows cap type of second order polynomial after filling the level. 3. if damage occurs beneath half of the draft, changes of head and displacement, and sinking speed follow almost straight lines. 4. by careful observation, sinkage speed could be predicted.

• 수산해양기술연구
• /
• 제40권1호
• /
• pp.17-22
• /
• 2004

This study was carried out at the CWC of Chosun university for the purpose of resistance performance improvement of planing hull, and the results of the tests were confirmed cooperatively with WJFEL. G/T 100 ton class planing hull form was selected, and the improvement of hull form including appendages were performed by using some model test techniques. The model test scope comprises resistance relative tests including wave profile observation, trim and sinkage measurement and flow visualization tests at full load and trial conditions for one bare hull and for two appended hulls. The final wedge and spray strip combined with improved hull form showed about 1.0 knot speed improvement at both of full and trial conditions, and outstanding improvement for fore wave phenomena.