• Journal of Korean Society of Water and Wastewater
• /
• v.8 no.2
• /
• pp.43-52
• /
• 1994

In this paper, the unit processes in the typical water treatment plant, which need to be expanded because the water demand is over the existing water treatment capacity in the near future, were carefully examined to upgrade the water treatment plant. The models were installed in the fields as a distorted model based upon the hydraulic similitudes. The models having the constant discharge ratio in the unit processes between the model and the prototype were installed as two units to compare the treatment efficiencies. The capacity of the individual unit, which is a model of the prototype of $250,000m^3/day$ capacity, was $24m^3/day$. In the mixing and flocculation experiments, the mixing intensity of flocculators G was selected as the main experimental item. The optimal mixing intensities G, which are 65/sec for experimental discharge of $1m^3/hr$ and 85/sec for experimental discharge of $1.3m^3/hr$, are identified based upon the comparison the relative turbidity removal efficiencies. Also, the outlet weir loading was selected as the main experimental item in the sedimentation process. Through the continuous experiments with the main experimental items of the mixing intensity of flocculators G and the outlet loading of the weir in the sedimentation basin, about 20% upgrading compared to the existing water treatment capacity was obtained.

• Journal of environmental and Sanitary engineering
• /
• v.20 no.3 s.57
• /
• pp.51-56
• /
• 2005

Allocation of water pollution load from loading capacity can be much essential, controversial, and its standards can be applied case-by-case to the various situations. Allocation methods to point sources are generally 'Equal effluent concentration', 'Equal percent Treatment', Loading capacity at planning stage consists of basic pollution load, development pollution load, reserved pollution load and margin of safety. But at the implementing stage loading capacity can be consisted of allocatable load and margin of safety to give more flexibility in the total water pollution load management plan. In that case, we can re-adjust and altogether use the pollution load of point sources of series and non-point sources at the implementing stage.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.3
• /
• pp.188-197
• /
• 1997

Effect of martensite morphology on damping capacity and hardness of Fe-Ni-C martensitic alloys were studied. The morphologies of martensite such as lath, butterfly, lenticular and thin plate were prepared by adjusting nickel content and austenite grain size. The hardness increased in order of lath, lenticular, thin plate, butterfly. The damping capacities of the lath and butterfly martensites were higher than those of the other two morphologies, indicating that the dislocation substructure is more effective in the damping capacity than the twin substructure. Especially, the butterfly martensite showed the highest damping capacity among these morphologies because of presence of not tangled but free dislocations in there.

• Journal of Power System Engineering
• /
• v.22 no.1
• /
• pp.87-93
• /
• 2018

Specimens were machined out from hot-rolled AZ31 magnesium alloy, and deformed at 623K with rolling reduction of 30%. After hot rolling, specimens were annealed at various range of temperature and time. In this study, static recrystallization was occurred during heat treatment, however, variation of main component and intensity of texture was not revealed. The results of microstructure observation, damping capacity test and dislocation mechanism indicated that increasing of damping capacity was caused by grain growth. It means that grain size is effective factor to damping capacity.

• Journal of the Korean Society for Heat Treatment
• /
• v.11 no.2
• /
• pp.92-98
• /
• 1998

Degradation and recovery of damping capacity in a Cu-65%Mn alloy have been studied. When the alloy was isothermally aged at $400^{\circ}C$, the highest damping capacity was observed after aging for 4 hours. In case when the alloy aged at $400^{\circ}C$ for 4 hours was maintained at $100^{\circ}C$, the damping capacity gradually decreased with time. The microstructural observations showed that the formation of subdomains and ${\alpha}$-Mn precipitates are responsible for the degradation of damping capacity. When the degraded specimen was reheated at $250^{\circ}C$ for 30 minutes, the damping capacity was recovered considerably owing to the redistribution of impurity atoms, the extinction of subdomains and the release of damping sources from ${\alpha}$-Mn precipitates during the repeated transformation, fcc${\leftrightarrow}$fct.

• The korean journal of orthodontics
• /
• v.46 no.6
• /
• pp.386-394
• /
• 2016

Objective: The objective of the study was to evaluate the practicality and the validity of different surface treatments of self-drilling orthodontic mini-implants (OMIs) by comparing bone cutting capacity and osseointegration. Methods: Self-drilling OMIs were surface-treated in three ways: Acid etched (Etched), resorbable blasting media (RBM), partially resorbabla balsting media (Hybrid). We compared the bone cutting capacity by measuring insertion depths into artificial bone (polyurethane foam). To compare osseointegration, OMIs were placed in the tibia of 25 rabbits and the removal torque value was measured at 1, 2, 4, and 8 weeks after placement. The specimens were analyzed by optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). Results: The bone cutting capacity of the etched and hybrid group was lower than the machined (control) group, and was most inhibited in the RBM group (p < 0.05). At 4 weeks, the removal torque in the machined group was significantly decreased (p < 0.05), but was increased in the etched group (p < 0.05). In the hybrid group, the removal torque significantly increased at 2 weeks, and was the highest among all measured values at 8 weeks (p < 0.05). The infiltration of bone-like tissue surface was evaluated by SEM, and calcium and phosphorus were detected via EDS only in the hybrid group. Conclusions: Partial RBM surface treatment (hybrid type in this study) produced the most stable self-drilling OMIs, without a corresponding reduction in bone cutting capacity.

• Journal of the Korean Society for Heat Treatment
• /
• v.15 no.6
• /
• pp.272-278
• /
• 2002

The changes in damping capacity with volume fractions of thermal and deformation-induced ${\varepsilon}$ martensites were compared and analyzed in an Fe-23%-Mn alloy. The volume fraction of thermal ${\varepsilon}$ martensite increased with decreasing cooling temperature, whereas that of deformation-induced ${\varepsilon}$ martensite increased steeply up to 10%- of cold rolling and nearly saturated in further cold rolling. In the case of thermal ${\varepsilon}$ martensite, the damping capacity increased linearly with the increase in ${\varepsilon}$ martensite content. For the deformation-induced ${\varepsilon}$ martensite, however, the damping capacity increased continuously up to 70%- of ${\varepsilon}$ martensite, over which it decreased suddenly. TEM microstructures showed that the deterioration of damping capacity above 70%- of deformation-induced ${\varepsilon}$ martensite is ascribed to the introduction of perfect dislocations, which play a important role in inhibiting the movement of damping sources such as stacking fault boundaries inside ${\varepsilon}$ martensite, ${\varepsilon}$ martensite variant boundaries and ${\gamma}/{\varepsilon}$ interfaces.

• Journal of Power System Engineering
• /
• v.16 no.4
• /
• pp.60-65
• /
• 2012

This study was carried out to investigate the effect of reverse transformation on the damping capacity in high manganese austenitic stainless steel. ${\alpha}^{\prime}$-martensite was formed with the specific direction and surface relief by deformation. Over 95% of the austenite phase was transformed to deformation-induced ${\alpha}^{\prime}$-martensite by 70% cold rolling. Reverse transformation became rapid above an annealing temperature of $550^{\circ}C$, but there was no significant transformation above $700^{\circ}C$. In addition, with increasing annealing time at $700^{\circ}C$, reverse transformation was induced rapidly, but the transformation was almost completed at 10 min. Damping capacity was increased up to $700^{\circ}C$, and than unchanged with the increasing annealing temperature. Damping capacity increased steeply with an increasing reverse treatment time up to 10min, whereas there were no significant change with a treatment time of more than 10 min. Damping capacity increased with an increasing the reversed austenite and was strongly affected by reversed austenite.

• Journal of the Korean Society for Heat Treatment
• /
• v.27 no.6
• /
• pp.295-301
• /
• 2014

In this study, the relationship between strength and damping capacity of annealed magnesium alloys after hot rolling was investigated. The microstructure of hot rolled magnesium consisted of dendrite structure and $Mg_{17}Al_{12}$ compounds precipitated along the grain boundary. The dendrite structure was dissipated, $Mg_{17}Al_{12}$ compounds was decomposed by annealing, and then its dissolved in ${\alpha}$-Mg. With an increasing the annealing temperature and time, strength was slowly decreased and damping capacity was slowly increased by the growth of grain size and decreasing of defects induced by hot rolling. In annealing treatmented magnesium alloys after hot rolling, damping capacity was decreased rapidly with an increase of strength. There was on proportional relationship between tensile strength, and damping capacity.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.1
• /
• pp.47-54
• /
• 1997

Flake graphite cast irons with the high damping capacity have been used for the control of vibration and noise occuring in the members of various mechanical structures under vibrating conditions. However, the damping capacity which is morphological characteristics of graphite is one of the important factors in reducing the vibration and noise, but hardly any work has deal with this problem. Therefore, the authors have examined the damping capacity of various cast irons with alloying elements and studied the influences of the matrix, mechanical properties and morphological characteristics of graphite. The main results obtained are as follows: Effects of Ni on the damping capacities and mechanical properties are investigated in 3.9%C-0.3% Cu gray cast iron. At 0.2% Ni content, specific damping capacity showed the maximum value, and decreased with further increase in Ni content, Graphite continuity also showed same behavior. This indicates that the specific damping capacity has a close relation with graphite continuity. On the other hand, the damping capacity in pearlite matrix showed superior to that in ferrite. In contrast, with increasing the Ni content, both tensile strength and hardness increased due to the decrease of graphite length and eutectic cell size.